Instruction Manual

5.2. BEFORE FIRST USE
5.2.1. Before operating the press, purge the hydraulic system in order to eliminate any air that may have built up during transit. Open the
release valve and pump the handle several times and close the release valve. Should the system malfunction at any time, repeating
this process may resolve the problem.
▲ DANGER! Models are purpose designed to withstand greater loads than the hydraulic units can develop. For safety reasons, always
ensure the workpiece and press tools are secured on the table and will not flex or suddenly “give way” causing danger to operator or
the component. Also ensure you have read and understood section1 Safety Instructions.
5.3. The transit valve on the bottom of the pump (opposite end to the handle) needs to be open during operation.
6. OPERATION
6.1. Check that the hydraulic unit is fully closed ready for operating.
6.2. Position the table at the required operating height by inserting the pins into the appropriate holes in the frame.
6.3. Position the V-block plates or press tools to be used onto the table and align beneath the ram. Place workpiece onto the table or V-blocks
and align beneath the ram as required. Note: Care must be taken to ensure a V-block does not fall from the press table. If necessary hold
the configuration in position with clamps (not supplied).
6.4. Operate the pump slowly until the ram is close or just touching the workpiece. Before applying real pressure to the workpiece recheck the
alignment with the ram and ensure that the workpiece and press tools are supported in such a way that they cannot flex to breaking point.
DO NOT exceed the stroke indicated on the label or the red mark on the piston and DO NOT apply off centre loads.
6.5. When work is completed release the pressure using the knob with four lugs and the piston and the ram head will retract automatically.
Note: Always keep the piston retracted after use to avoid corrosion.
7. MAINTENANCE
Note: Maintenance and repair must be carried out by qualified person. Contact your Sealey stockist for details.
7.1. Check all fittings are tight before each use.
7.2. Lubricate all moving parts at regular intervals.
7.3. Always keep the press clean, dry, and protect from harsh conditions.
7.4. Should you need to replace the oil ensure the piston is fully retracted. An excess of oil will render the press inoperative.
Use only appropriate Sealey hydraulic jack oil. DO NOT use brake fluid. Contact your local Sealey stockist for details. Purge the system
to remove any air.
7.5. Check your model parts information for spares. Repair kits are available.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE MACHINE.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN PRODUCT TO US. Please telephone us on 01284 757500 to obtain the address and phone number of your local
agent.
If the product is under guarantee please contact your stockist.
De-commissioning Product
Should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of
the product and the oil according to local regulations.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
Original Language Version
© Jack Sealey Limited
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our
technical team on [e-mail] or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
YK20F.V5 Issue 1 18/01/23
REGISTER YOUR
PURCHASE HERE