SL-07 Series Marine Lantern Installation & Service Manual Version 1.
SL-07 Series 1–4NM+ Marine Lanterns Table of Contents Introduction........................................................................................................ Page 4 Operating Principle........................................................................................... Page 4 Technology......................................................................................................... Page 4 SL-07 Series Models.........................................................................
SL-07 Series 1–4NM+ Marine Lanterns Introduction Congratulations! By choosing to purchase a Sealite lantern you have become the owner of one of the most advanced LED marine lanterns in the world. Sealite Pty Ltd has been manufacturing lanterns for over 25 years, and particular care has been taken to ensure your lantern gives years of service.
SL-07 Series 1–4NM+ Marine Lanterns SL-07 Series Models 1-4NM+ Stand Alone Marine Lanterns The SL-07 series are LED marine lanterns designed to offer superior visibility and operate in conjunction with existing or purpose-built power supplies. With a variable range of 1 to 4NM, a maintenance-free light source and 256 user adjustable flash codes, the SL-07 series of LED lanterns is an ideal choice for operators seeking to fit a short-range marine lantern to existing or independently designed power sources.
SL-07 Series 1–4NM+ Marine Lanterns SPECIFICATIONS•* SL-07LB SL-07 Intensity Adjustments LED Life Expectancy (hours) High efficiency LED Red, Green, White, Yellow, Blue Red - 63 Green - 62 White - 65 Yellow - 60 1-4+ 360 7 Up to 256 IALA recommended (user adjustable) Multiple intensity settings >100,000 High efficiency LED Red, Green, White, Yellow, Blue Red - 63 Green - 62 White - 65 Yellow - 60 1-4+ 360 7 Up to 256 IALA recommended (user adjustable) Multiple intensity settings >100,000 Power Comsump
30° SL-07 Series 1–4NM+ Marine Lanterns SL-07-L Model 16 X 15 Radial Slots 6 Places 57 30° 181 PCD 231 57 181 SL-07 Model 231 Latest products and information available at www.sealite.
SL-07 Series 1–4NM+ Marine Lanterns Installation of SL-07 Series Models Lantern is activated by the connection of positive and negative wires to battery or mains system. Flash setting needs to be set prior to activation. 1. Remove the marked flash adjustment bung from the base of the lantern and set rotary switches to the required flash code (see ‘Selecting a Flash Code’ section of this manual). 2. Replace flash adjustment bung. 3.
SL-07 Series 1–4NM+ Marine Lanterns Selecting an Intensity/Power Setting Intensity/power settings on Sealite lanterns operate via DIP switches, located near the rotary switches on the flasher unit. The intensity/power settings may be used to reduce the power consumption and intensity of the lantern. Setting the lantern to 25% intensity will reduce the power consumption to 25% of the normal 100% setting and the range by 20% - 40% depending on the maximum intensity.
SL-07 Series 1–4NM+ Marine Lanterns Selecting a Flash Code - Rotary Switches A & B All lanterns have 2 rotary switches marked A and B on the flasher unit. Turning the small arrows to the appropriate number or letter will set the code. The unit may take up to one minute to activate a new flash code. A comprehensive list of available flash codes is listed on in the ‘Flash Codes’ section of this manual. 2.7 BCD F01 Latest products and information available at www.sealite.
SL-07 Series 1–4NM+ Marine Lanterns Flash Codes The Sealite SL-07 Series may be set to any of 256 IALA recommended flash settings which are useradjustable onsite without the need for external devices. SEALITE® code reference is listed by number of flashes For the latest version of this document visit www.sealite.com or email info@sealite.com Symbols FL Flash followed by number Eg.
IR SWITCH Controller A B 0 0 0 D 3 211 E 3 227 F 3 243 7 3 115 8 3 131 9 3 147 A 3 163 8 4 132 B 3 179 9 4 148 C 3 195 F 4 244 1 0 16 0 5 5 0 4 4 2 0 32 3 0 48 4 0 64 5 0 80 6 0 96 7 0 112 1 2 18 8 0 128 9 0 144 D 6 214 1 5 21 A 0 160 2 5 37 B 0 176 3 5 53 C 0 192 D 0 208 2 2 34 5 4 84 E 2 226 4 6 70 4 5 69 5 5 85 E 0 224 F 0 240 6 5 101 0 1 1 1 1 17 2 1 33 3 2 50 3 6 54 F 2 242 3 1 49 8 5 133 4 1 65 5 1 81 9 5 149 6 1 97 FLASH CODE ON OFF F (Steady light) VQ 0.5 S VQ 0.6 S VQ 0.
SL-07 Series 1–4NM+ Marine Lanterns SWITCH A B 0 A E B 1 A 2 A 3 A F 9 2 C 4 A 0 7 1 7 9 B 2 9 5 A 7 8 A A 6 A 7 A 9 9 2 8 3 7 3 9 A 9 7 B 8 A 4 7 8 8 5 7 4 C 5 C F B 9 A 6 7 7 7 6 9 8 7 B 9 9 7 4 9 B A C 9 D 9 A 8 A 7 8 B C A D A SWITCH A B 7 9 5 9 0 C E 9 3 C 2 B IR Controller 10 235 26 42 58 249 44 74 7 23 155 41 90 120 170 106 122 153 40 55 57 169 123 138 71 136 87 76 92 251 154 103 119 105 135 185 151 73 186 201 217 168 167 139 202 218 IR Controller 121 89 12 233 60 43 FLASH CODE ON OFF ON OFF F
SWITCH A B A B F A 0 B B 7 B 8 C 8 C B C 7 D B D 7 3 8 8 9 B B D 8 1 B E A E 7 B 6 4 8 5 8 1 8 F 7 9 D 0 8 F 8 0 9 1 9 6 8 1 C 4 B 3 B 5 B 6 B SWITCH A B B F B D 8 D 1 D 2 D F E B E 4 F C E 3 D A D 4 D 8 E 7 D D E C D 5 D 0 D 3 F 0 F E E 6 F IR Controller FLASH CODE ON OFF ON OFF ON OFF 171 250 11 183 184 200 203 199 219 215 56 137 187 216 27 234 231 182 72 88 24 247 157 8 248 9 25 104 28 75 59 91 107 Q (3) 6 S FL (3) 8 S FL (3) 9 S FL (3) 9 S FL (3) 10 S FL (3) 10 S FL (3) 10 S FL (3) 10 S FL (3
SL-07 Series 1–4NM+ Marine Lanterns IR SWITCH Controller A B D D 221 E D 237 E 8 232 5 F 95 9 F 159 9 E 158 IR SWITCH Controller A B F D 253 A F 175 7 F 127 IR SWITCH Controller A B 6 E 110 7 E 126 2 F 47 2 E 46 3 E 62 8 F 143 IR SWITCH Controller A B 4 E 78 5 E 94 1 F 31 0 E 14 1 E 30 IR SWITCH Controller A B FLASH CODE ON OFF ON OFF ON OFF ON OFF ON OFF Q (5) 7 S Q (5) 10 S FL (5) 12 S FL (5) 20 S FL (5) 20 S FL (5) 20 S 0.3 0.3 0.5 0.5 0.8 1.0 0.7 0.7 1.5 0.5 1.2 1.0 0.3 0.3 0.5 0.5 0.8 1.
SL-07 Series 1–4NM+ Marine Lanterns GPS Synchronisation The SL-07 Series come with GPS fitted as standard, and provide the user with the ability to install independently operating lanterns that all flash in synchronisation. No additional power supplies, aerials or control systems are required, and with its microprocessorbased system, the GPS option is specifically designed to provide maximum reliability and performance over a wide range of environmental conditions.
SL-07 Series 1–4NM+ Marine Lanterns Lantern Status Two status LED’s on the main printed circuit board provide the operator with an indication of the lantern status. There is one red and one yellow status LED. The red status LED is used to indicate the health of the lantern’s power system. The yellow status LED is used to indicate the operational status of the lantern. These indicator LED’s can be viewed at the base of the lens. Latest products and information available at www.sealite.
SL-07 Series 1–4NM+ Marine Lanterns All Sealite boards are fitted with two Indicator LED’s. These are positioned near the Flash Code Rotary Switches. Use the table below to help determine operational status. Yellow LED Lantern Status Lantern OFF Normal OFF Lantern is in Daylight and in Dusk till Dawn mode or in Standby Mode Flashing ON 0.15 seconds OFF 0.15 seconds Normal OFF Light is activating and will turn on after detecting 30 seconds of continuous darkness.
SL-07 Series 1–4NM+ Marine Lanterns Optional IR Remote Control The IR remote is used to communicate with Sealite lighting products that have an IR sensor fitted. The remote control is used for the following functions: Test / Configure • Flash Code: read the current flash code, configure a new flash code. • Lamp Intensity: read the current lamp intensity, configure a new intensity level. • Ambient Light Thresholds: read the current light thresholds, configure new ambient light thresholds.
SL-07 Series 1–4NM+ Marine Lanterns IR Controller Functions Test Mode / Configure T/C 1 4 7 R FC 1 4 7 1 R 4 FC 7 R FC Pressing the T/C button for upto 5 seconds places the light in Test Mode. The light will flash once in response to the T/C button being pressed and then turn off. 2 3 5 6 T/C 9 T/C 1 2 3 Normal T/C Operation L 0 The light will return to normal operation once it has not detected a valid key press for 30 seconds.
4 5 6 17 2 8 3 9 4R 50 6L 7 FC 8I 9B Flash Code SL-07 Series 1–4NM+ Marine Lanterns This key sets the flash code on the light. R 0 L T/C FC 1I 2B 3 T/C 4 5 1 6 2 Example Key sequence: 3 This sets the flash code to value 123. The light responds by flashing the flash code value. T/C Code Numbers Flash 4 5 6 7 8 9 1 2 3 The flash for 7 8 9 L long flash. 0 0 is one T/C R number For example if the current Flash Code is set to 51 via the AB switches, the lamp will flash number 081.
SL-07 Series 1–4NM+ Marine Lanterns Lux L x T/C This key sets the ambient light threshold levels. The format is L x T/C Where ‘x’ is the desired setting from the table below. There are 5 programmable lux levels which are set together for the sunset and sunrise transitions.
1 2 3 4 5 6 7 R FC SL-07 Series 1–4NM+ Marine Lanterns Error Indication T/C 8 / Acknowledge 9 If the key sequence is invalid, or an out of bounds value is attempted to be set, the light flashes 5 times for 1 second. (The command then needs to be sent from the start.) 1 0 2L 3 4I 5B 6 T/C Example key sequence: (Set the intensity level to 5 – undefined.) The light flashes 5 times for 1 second.
SL-07 Series 1–4NM+ Marine Lanterns Hibernation Mode (Advanced users) L d I d m m y y T/C For situations where the lantern is put into storage for a known period, the IR Remote control can be used to configure the lantern into Hibernation Mode for a user programmable date range. Hibernation of the battery power by disabling the light (will not activate m d maximises d mconservation L I Mode at night) and shutting off the GPS receiver to rely on the internal clock for date checking.
R R R L I SL-07 Series 1–4NM+ Marine Lanterns 1 T/C Disable Hibernation / Hibernation Modes L I 2 T/C L I 0 T/C Pressing the following key sequence will disable (turn off) both Hibernation Mode and Seasonal Hibernation: and the lantern will respond with a single long flash. The Lantern will disable Hibernation Mode and enter Dusk-to-Dawn Mode.
SL-07 Series 1–4NM+ Marine Lanterns Storage Mode (Advanced users) For situations where the lantern is put into storage but with access to daylight, the IR Remote control can be used to configure the lantern into Storage Mode. This mode manually forces the lantern to turn off, but with access to daylight it will still charge battery pack. However the lantern will not keep track of the date. In Storage Mode, the GPS is disabled however the lantern will still respond to IR commands.
SL-07 Series 1–4NM+ Marine Lanterns Maintenance & Servicing Designed to be maintenance free, the SL-07 Series requires minimal attention, though the following maintenance and servicing information is provided to help ensure the life of your product. 1. Cleaning Lens- occasional cleaning of the light lens may be required. Using a cloth and warm soapy water, wipe off any foreign matter before rinsing the lens with fresh water. 2.
SL-07 Series 1–4NM+ Marine Lanterns Trouble Shooting Problem Remedy Lantern will not activate. • • • • • • Timing codes will not change. • Turn rotary switches several times to ensure contacts are clear. Lantern will not operate for the entire night. • Reducing the light output intensity or duty cycle (flash code) will reduce current draw on the battery. Ensure internal toggle switch is set to the ‘ON position. Ensure lantern is in darkness.
SL-07 Series 1–4NM+ Marine Lanterns Sealite LED Light Warranty V2.1 Activating the Warranty Upon purchase, the Sealite Pty Ltd warranty must be activated for recognition of future claims. To do this you have two (2) options: 1. Postal Registration - please complete the Sealite Warranty Registration Card and return to Sealite within 30 days of your purchase. 2. Online Registration - please complete the Online Registration Form at; www.sealite.
SL-07 Series 1–4NM+ Marine Lanterns 3. The customer must give Sealite Pty Ltd notice of any defect with the product within 30 days of the customer becoming aware of the defect. 4. Rechargeable batteries have a limited number of charge cycles and may eventually need to be replaced. Typical battery replacement period is 3-4 years. Long term exposure to high temperatures will shorten the battery life.
SL-07 Series 3-4NM+ Marine Lanterns Other Sealite Products Available Marine Lanterns (1-12NM+) Monitoring & Control Systems Bridge & Barge Lights Marine Buoys (up to 3mt in diameter) Area Lighting Mooring Systems & Accessories Head Office Sealite Pty Ltd 11 Industrial Drive Somerville, Vic 3912 Australia Tel: +61 3 5977 6128 Fax: +61 3 5977 6124 Email: info@sealite.com Internet: www.sealite.com Latest products and information available at www.sealite.