SEARS OWNERS MANUAL HOME CLEANING SYSTEM i MODEL NO. 175.8670290 CAUTION: Read Instructions and Rules for Safe Operation Carefully Kenmore HOME CLEANING. SYSTEM For Household Use Only Save this Manual for Future Reference SEARS, 661654-146 ROEBUCK (06SO) Rev. , • • • • INTRODUCTION ASSEMBLY OPERATION MAINTENANCE REPAIR PARTS AND CO., Dept. D/731 CR-W, Sears Tower, 10Ooo) Chicago, IL 60684 _]NTED IN U.S.
IMPORTANT SAFETY INSTRUCTIONS --Readallinstructions before using thiscleaner. When using any electri_l appliance, basic precautions should always be followed, including the following: WARNING 1. 2. 3. -To reduce the risk of fire, electric shock, or injury: Do not leave cleaner when plugged into electrical outlet. Unplug from outlet when not in use and before servicing. WARNING" TO AVOID ELECTRIC SHOCK, DO NOT EXPOSE TO RAIN -- STORE INDOORS.
TABLE OF CONTENTS Safety Instructions ..................................................... page 2 Additional Uses I Optional Accea,.,_ories.................. page 8-g Warranty .................................................................... page 3 Trouble Shooting Chart ........................................... page 10 introduction ................................................................ page 3 ,_xploded Views and Parts Lists ........................ page 11-15 Assembly ......................
ASSEMBLY ASSEMBLY OF RECOVERY TANK AND SOLUTION POWER EAD TANK See Figure 2 1. Place Recovery Tank into Solution Tank (align the word "VACUUM" on Recovery Tank with =VACUUM" on Solution Tank) and secure with Metal Latch. 2, Insert the plug onthe Short Cord from the Solution Tank into the Recovery Tank Power Head. ASSEMBLY OF HOSE, WANDS, NOZZLE AND SOLUTION TUBING PLUG SHORT CORDIN HERE RECOVERY TANK METAL LATCH SHORT CORD See Figure I 1. Assemble the two Straight Wands. 2.
OPERATION CARPET PREPARATION For best results prepare carpet for cleaning as follows: 1. Vacuum carpet 11oremove loose dirt before using Cleaner. 2. To remove stains and ground in dirt present in heavy traffic areas of the carpet, spray or rub Sears Heavy Traffic ProTreatment (82833) into carpet before u_ing Cleaner. Follow directions on the bottle. FILLER OPENING FILLING CLEANER WITH WATER AND CLEANING SOLUTION See Figure 4 1, Open I'_1ofthe Filler Opening, 2.
OPERATION TEST FOR SOLUTION SPRAY See FTgure 6 1. Hold Floor Nozzle above floor level. 2. Pull Solution Release Trigger on Angled Wand. 3. Observe Floor Nozzle to make sure oleaning solution is being sprayed evenly. (see DETAIL _A") SOLUTION RELEASE TRIGGER NOTE: If solution is not being sprayed evenly, refer to Trouble Shooting Chad. FLOOR sPRAYS OF SOLUTION CLEANING THE CARPET See F_gures 7 & 8 Solution Dispensing Stroke: 1, Sfad at a comer (recommended). 2.
OPERATION WHEN TO EMPTY RECOVERY TANK See Figure 9 During normal operation, your cleaner may stop recovering solution from your carpet. When this occurs there are three check points to alert you: 1. An increase in motor noise. 2. No solution visibly being recovered by the floor nozzle. 3. No air coming from the exhaust port of your cleaner. EXHAUST PORT RECOVERY TANK W_en this occurs: 1, The Recovery Tank is full and the Float Valve in the Recovery Tank has been activated.
OPERATION TO EMPTY THE SOLUTIONTANK METHOD 1 See Figure 11 When (:leaning is completed, both the Recovery Tank and the Solution Tank should be emptied prior to storage. Empty the Recovery Tank as described earlier. There are three methods of emptying the Solution Tank. Method 1 : 1. Disconnect Pump Cord from Recovery Tank, 2. Remove Recovery Tank from Solution Tank and pour solution out of the Filler Opening. Method 2: 1. Place Floor No_le in bath tub or container. 2.
ATTACHMENTS UPHOLSTERY NOZZLE See Figure 13 The Carpet Cleaner Upholstery Nozzle is an attachment for furniture upholstery cleaning, The upholstery nozzle may also be used to clean auto upholstery or carpeting. In addition, the nozzle may also be used to clean carpeted stairs and other areas difficu# to clean with the normal floor nozzle. FLOOR TOOLS See Figure 14 The Bare Floor/Carpet Brush (1) may be used on floors without aarpet for DRY cleaning with Paper Dust Beg Installed.
TROUBLE SHOOTING CHART PROBLEM POSSIBLE SOLUTIONS* 1. Neither vacuum motor nor pump motor runs. 1. Be sure power switch is in "ON" position_ 2. Be sure power cord is plugged in securely. 3. Check wall electrical outlet (by plugging in a known working electrical appliance). 2. Vacuum motor runs, but there is no spray at the nozzle. 1. Be sure Electrical Cord from Power Head to Solution Tank is securely plugged into receptacle on the Power Head. 2. Check that Solution Tank is full. 3.
SEARS HOME CLEANING SYSTEM -- MODEL 175.8670290 SEE PAGE 13 FOR F.
SEARS HOME CLEANING SYSTEM --- MODEL 175,8670290 33 11 _2 13 19 20 21 44 '_
SEARS HOME CLEANING KEY 1 2 3 4 5 6 7 6 9 10 11 12 13 14 SYSTEM -- MODEL 175.8670290 PART NO, 642315-012 64,L125-OO7 642600-039 641768-004 641838-001 643741-002 643509-001 642149-004 641843-010 642367-006 644548-001 642367-004 643909-902 642367-004 DESCRIPTION Switch Cap Handle Plme Label Handle Shroud w/Label Motor Housing Screw Switch Screws (2) Female Pigtail Switch Wiring Nut (4) Power Cord Motor Seal Motor Cover Motor Seal Carbon BmehAsm.
SEARS HOME CLEANING SYSTEM -- MODEL 175.8670290 I 18 16 1,5 14 17 1 ( l..................
SEARS HOME CLEANING KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 ,_4 25 PART NO. 662257-001 862262-001 644037_002 644848-006 643731-005 644038-003 644773-005 644773-007 643502-009 643570-09.3 661404*0O3 663324-001 644038-001 643572-007 662266-001 662266-002 662264-001 662263-001 643186_18 643571-013 644159-003 643076-009 642458-005 643737--013 663324-002 661654-146 SYSTEM--- MODEL t75.
Kenmore SEARS OWNERS MANUAL SERVICE MODEL NO. 175.8670290 HOW TO ORDER REPAIR PARTS HOME CLEANING SYSTEM _Now that you have purchased your Kenmore Home Cleaning System, should a need ever exist for repair parts or service, simply contact any Sears Service Center. Be sure to provide all pertinent facts when you call or visit. The model number of your Power Spray Cleaner will be located on the Po_,er Head of the cleaner.
