TM C R O S S TR A ININ SE_/AJRS i ¸ G S Y TE M 0 WNER 'S MAN UA L Model No. 831.159231 Serial No. The serial number can be found in the IotaS'onshown below. Write the serial number in the space above, Serial Number Decal CAUTIONh Read all safety precautions and instructions in this owner's manual before using this equipment. Save this owner's manual in a safe place for future reference. PATENT PENDING SEARS, ROEBUCK AND CO.
TABLE OE CONTENTS IMPORTANT SAFETY PRECAUTIONS ................................................ 2 BEFORE YOU BEGIN .... . ......................................................... ASSEMBLY, .... ,_.,_,.. .......................................................... OPERATION AND ADJUSTMENT, <_.: MAINTENANCE AND TROUBLE-SHOOTING PART LIST , :.,, ...' .......... ,. .................................................. EXPLODED DRAWING ............................................................. 3 4 .
BEFORE YOU BEGIN Congratulations for seiecting the SEARS ® LIFESTYLER SYSTEM 50 ERS cross training system. The unique LIFESTYLER SYSTEM 50 ERS is a total body conditioning system, offering both weight traihing and aerobic exercises. M0v_ng from station to station on the LIFESTYLER SYSTEM 50 ERS is quick and easy, and the digital hand control allows you to change weight with the touch of a button.
ASSEMBLY Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Read all steps carefully before beginning. See the PART I.D. CHART accompanying this manual for a drawing of each small part used In assembly list of the tools needed. The assistance of a second person is recommended.
. Press four Large Bushings (671. (15) into the Support Arm 5 24 Tap a 1/2" Dome Cap (24) onto one end of the 9 1/4" Axle (71). Liberally grease the Axle, Turn the Support Arm(67) so the decal is away from the Frame (1):, Insert the 9 1;_4"Axle through the Support Arm and the Frame as Shown, Tap a 1/2" Dome Cap (24) onto the other end of the Axle. 6 Wet the lower end of the Left Butterfly Arm (65) and the inside of a Butterfly Pad (61) with soapy water.
10. Press a 1 1/2" x 1 1/2" Inner Cap (19) into the Ab Arm (21). Wet the upper end of the Ab Arm and the inside of the Ab Arm Pad (25) with soapy water. Slide the Pad onto the Ab Arm. lO N Tap a 1/2" Dome Cap (24) onto one end of the 3" "D"Axle (23). liberally grease the Axle. Align the Ab Arm (21) with the bracket on the Ab Frame (3). Insert the 3" "D"-Axle into the Ab Frame and the Ab Arm. Tap a 1/2" Dome Cap (24) onto the other end of the Axle.
15. Separate the ends of the Conirol Stand (29) and slide 15 the Plastic Sleeve (30) onto one end. Bring the ends tOgether and _enter the Plastic Sleeve between them. Plug one end of the Control Cord (27) into the Hand Control (28). Plug the other end of the Cord into the Wire Adapter 27 (74) at the front of the system. Attach the Hand Control (28) to the Control Stand (29) with the two 1/2" Tap Screws (31). Plug the Power Cord (26) into the socket at the backof the system.
USING THE STEPPER The stepper features precision resistance cylinder s for long life and trouble-free nature of resistance cylinders, it is recommended that the floor underneath case of slight oil leakage. WARNING: The resistance cylinders become the cylinders to cool before touching them. operation; due _tothe the stepper be covered in very hot during use. Allow The resistance of the stepper pedals can be changed by moving the resistance brackets. Change the resistance of one pedal at a time.
OPERATING THE BUTTERFLY ARMS Storage To operate the butterfly arms in the press arm mode, insert the Pull Pins (68) into the support arm and the butterfly arms as described in assembly To operate the butterfly step 6 on page 5. arms in the butterfly mode, remove the Pull Pins from the support arm and the butterfly arms. Insert one Pull Pin into the frame extension and the Frame Extension, support arm. Insert the other Pull Pin into the indicated storage hole. See figure 5.
PART LIST--Model Key Part No. No. Qty. 1 2 3 4 5 6 7 8 NSP 109864 108861 108834 111175 012108 014O62 013456 9 10 11 12 13 14 15 16 17 18 19 20 013322 109865 1O9866 106872 105723 103735 109867 109868 107048 013564 103833 108729 21 22 23 24 109869 013574 109870 103903 26 27 28 29 101067 106786 105922 36 37 38 39 4O 41 42 43 44 45 _,6 47 _10 108982 108673 103860 109794 109795 108832 105134 110266 013341 013519 109871 100151 109872 109873 107367 105142 012082 1O9875 105315 Rev.
EXPLODED DRAWING--Model No. 831.159231 Rev.
ORDERING Each SYSTEM requesting REPLACEMENT has its own .MODEL service NUMBER. PARTS Always mention this MODEL when or repair parts for your SYSTEM. All parts listed her_.in may be ordered through most SEARS RETAIL STORES. SEARS, ROEBUCK AND CO. SERVICE tf parts you need are not stocked locally, your order will be transmitted DISTRIBUTION CENTER for handling. WHEN ORDERING NUMBER REPAIR 1. The MODEl_ NUMBER PARTS, ALWAYS GIVE THE FOLLOWING and PARTS INFORMATION: of the product (831.