™ owners manual Model No. 45-02181 26" LEAF/LAWNSWEEPER CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operating Maintenance Repair Parts the fastest way to purchase parts www.speedepart.com PRINTED IN USA FORM NO.
SAFETY RULES Remember, any equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when using this equipment. CAUTION: VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN ACCESSORY OR AN ATTACHMENT. BE AWARE OF CHANGING CONDITIONS ON SLOPES. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS — ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED.
ASSEMBLY INSTRUCTIONS HARDWARE PACK (NOT SHOWN FULL SIZE) TOOLS REQUIRED FOR ASSEMBLY (1) Phillips Screwdriver (1) Adjustable Wrench (1) 7/16" Open End or Box Wrench 1. Assemble the two Handle Leg Stand Tubes to the Sweeper Housing, using two hex bolts 1/4-20 x 1-1/4" long, flat washers and 1/4-20 hex lock nuts, per handle. See figure 1. Only hand tighten at this time. Ref. No. A B C D E F G H Description Hex Bolt, 1/4-20 x 1-1/4" Flat Washers 1/4" I.D.
3. Now tighten the four bolts from step 1. 7. Assemble the two plastic rod caps to the rod ends of the bottom bag rod. Assemble two Palnuts to the ends of the top bag rod. See figure 5. 4. Assemble a bag rod clip to the inside of each lower handle tube using a curved head bolt secured down against the clip using a 1/4" lock nut. The open end of the clips should face towards the sweeper housing. See figure 3. FIGURE 5 8.
9. Place the upper hopper bag and bag rod into the bag rod clips on the hopper handle. See figure 7. 11. Hook the elastic straps on the bag flaps under the bag rod clips on the lower handle tubes as shown in figure 9. FIGURE 7 FIGURE 9 10. Place the lower hopper bag and bag rod into the opening on the sweeper housing. See figure 8. OPERATION Take care when operating your sweeper. Operating your sweeper according to these instructions will help prevent damage and prolong the life of your sweeper.
WHEEL GEARS/PAWL SERVICE CAUTION: EYE PROTECTION SHOULD BE WORN WHILE OPERATING SWEEPER IMPORTANT: Do not remove both wheels at the same time to avoid mixing parts. (The R.H. and L.H. ratchet gears are not interchangeable.) Make notes on the position of washers and snap rings during disassembly. DUMPING OF SWEEPER 1. Remove only one wheel from the sweeper. 2. Remove the retaining rings and washers which hold the ratchet gear onto the brush shaft. 3. Remove the gear by sliding it off the brush shaft.
BRUSH REPLACEMENT 1. Remove the hopper bag from lawnsweeper. 2. Brush replacement should be done one brush at a time. 3. Tip the sweeper forward on housing for ease of brush replacement. Do not remove hex bolt from double brush retainers through brush shaft. 4. Loosen hex bolts and hex lock nuts from single brush retainers. See figure 13. Slide brush out of retainers, making not of over-lap bristles position. 5.
REPAIR PARTS FOR 45-02181 26" LEAF/LAWNSWEEPER
REPAIR PARTS FOR 45-02181 26" LEAF/LAWNSWEEPER REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PART NO. QTY. 44600 23784 44286 43681 44680 1543-69 44695 R19111116 43720 44946 23866 44598 43070 44684 1038 44685 40007 716-0106 44679 49946 741-0249 44692 43064 2674-32 48651 48652 47046 1 1 4 1 1 1 1 1 1 1 2 2 4 2 2 2 2 2 2 2 4 4 4 2 1 1 2 REF. NO.
NOTES 10
NOTES 11
the fastest way to purchase parts www.speedepart.com REPAIR PARTS Agri-Fab, Inc. 303 West Raymond Sullivan, IL. 61951 217-728-8388 www.agri-fab.com This document (or manual) is protected under the U.S. Copyright Laws and the copyright laws of foreign countries, pursuant to the Universal Copyright Convention and the Berne convention.