Installation Guide

ManualsBrandsSeaSun ManualsOutdoor ShadesMorro Bay Elite PVC Fabric Outdoor Roller Shade Rechargeable DC Motor Operated - 120 in. W x 96 in. L

Valance Bracket

(VB13) x 3

AC Adapter

(18ACC)

Qty:1

CUSTOMER SERVICE

Monday through Friday, from 7am - 4pm (MST). Please visit www.ShadeInfo.com to register your shade purchase.

IMPORTANT INFORMATION

We recommend two (2) people install this shade. Retain these instructions for future use. A power drill, tape measure,

leveling device, and Phillips screwdriver bit are recommended for installation (not included). Note: this shade must be

installed into wood studs. If woods studs are not available, anchoring hardware must be used (not included).

Tools required: phillips screwdriver, leveling device (laser level, standard level, etc.), and power drill (if pre-drilling the holes).

Note: your parts and fabric may differ in color than shown in this manual. Parts shown are not to scale. Pre-installed parts are not

shown in the part list below.

Remote Control and Related Hardware

Cable Tie Down System and Related Hardware

1.2 in Screw

(S09) x 6

Cable (RCS-CAB12) x 2

Cable Bracket System (RCS-CB12)

Cable Bracket - x 2

1 in Cable Bracket Screw (x4)

1 1/8 in Anchors (x4)

Remote Holder (x1)

0.75 in Anchor (x2)

Holder Bracket (x1) Screws (x2)

Remote Control w/ Battery (x1)

Hex Key (x1)

Cable Bolt

Cable Bolt Nut

Hex Lock

Remote Control and Mount System (14RIRC)

PARTS THAT ARE IN THE HARDWARE BOX

Exterior Motor Operated Sun Shade with Valance

Installation and Care Instructions

(Installation video available at www.shadeinfo.com)

Summary of content (8 pages)

PAGE 1
Exterior Motor Operated Sun Shade with Valance Installation and Care Instructions (Installation video available at www.shadeinfo.com) CUSTOMER SERVICE Contact us at 303.652.6164 for additional information. English speaking customer service representatives are available Monday through Friday, from 7am - 4pm (MST). Please visit www.ShadeInfo.com to register your shade purchase. IMPORTANT INFORMATION We recommend two (2) people install this shade. Retain these instructions for future use.
PAGE 2
Important: Do Not Cut the Antenna Your shade has an antenna that allows the Remote Control to communicate with the shade motor. Please do not cut the antenna (see antenna in Fig A). Step 1: Remove Protective Film from Valance Your shade is shipped with a protective film to prevent scratching during shipping. Please remove this film prior to installation. Fig A Step 2: Determine Your Installation Type Determine your type of installation. Your sun shade can be hung from a wall or a ceiling.
PAGE 3
Step 4: Install the Shade WALL INSTALLATION For wall installations, first hook the back of the Valance on the top of the Valance Brackets (Fig H), then rotate the shade down and click into place (Fig I). Note: you may need to push the plastic tabs on the Valance Brackets to help the shade click into place.
PAGE 4
Step 7: Set your top and bottom limits When rolling your shade up or down, you have the option of stopping the fabric at any position by pushing the stop button on your Remote Control. Your shade is pre-programmed with a “Fabric Top Limit” and a “Fabric Bottom Limit”. These are the points where the fabric will stop rolling without you pushing the “stop” button. The default “Fabric Top Limit” is approximately 4’’ below the valance. The default “Fabric Bottom Limit” is approximately 96’’ below the Valance.
PAGE 5
Step 8: Mount Remote Control to Wall (optional step) Your shade includes a Remote Control Holder that allows you to mount your Remote Control to a wall/beam. Important: if you mount your Remote Control, please make sure the remote is in a covered location. The Remote Control should not be exposed to rain, snow or direct sunlight.
PAGE 6
Step 9: (continued) Next, thread the Cable through the Bottom Tube Plug and make a vertical mark where the Cable intersects the horizontal mark (see Fig U). Note: you may need to roll the Fabric up to complete this part of the process. Align the top of the Cable Bracket with the horizontal line and centered on the vertical line you created using the Cables (see Fig V) and install using the provided 1 inch Screws (two screws per Cable Bracket).
PAGE 7
You can now control each shade individually by selecting their channel on your primary remote or you can control all shades at the same time on the primary remote by lighting all five (5) channels. Press the “channel increase” or “channel decrease” buttons until all five (5) channels are illuminated. Programming Help ERASING TOP AND BOTTOM LIMITS If your top and bottom fabric limits programming did not work properly or you want to change them, see the following instructions.
PAGE 8
Troubleshooting Problem Possible Reasons Solution Process Remote control battery is dead or has not been installed Install battery or replace battery (1 battery included in package) see installation instructions (step 5) Remote frequency has been deleted Re-program Remote See “programming help” follow instructions: erasing all frequencies (pg 7) Shade needs to be charged Charge Shade Use included AC adapter and plug in shade Remote battery not installed correctly Install battery correctly Rem