Installation Guide

ManualsBrandsSeaSun ManualsOutdoor ShadesSeaside HDPE Fabric Cordless Crank Operated Exterior Roller Shade - 120 in. W x 72 in. L

Crank Operated Shade with PE Fabric

Description Part Number Qty Included

Crank Bracket CBC18 1

Plug Bracket PB18 1

Bracket Cover (pre-installed) BC18 2

Crank Plug (pre-installed) CP18 1

Plug with pin (pre-installed) PBP18 1

Bracket Screws BSC18 4

Pole HP18 1

Bottom Rail Cap (pre-installed) BRC18 2

Bungee BUN18 2

Bungee Bracket BUNB18 2

Bungee Screw BUNSC18 4

Bungee Anchor BUNA18 4

INSTALLATION INSTRUCTIONS

Maintenance

To clean your shade, rinse with water and scrub with any non-abrasive cleaner (using

bleach or other abrasive cleaners will void your warranty). Roll shade down to air dry.

303.652.6164 (p)

Ceiling Mount or Left Crank Operation (or both)

Crank Bracket

(CBC18)

Figure A

Figure N

Figure O

Figure R

Figure S

Figure T

Figure P

Figure Q

WALL INSTALL, CRANK RIGHT

WALL INSTALL, CRANK LEFT

CEILING INSTALL, CRANK LEFT

CEILING INSTALL, CRANK RIGHT

M1026-E

Plug Bracket

(PB18)

Plug with Pin

(PBP18)

Crank Plug

(CP18)

Bottom Rail Cap

(BRC18)

Bungee

(BUN18)

Bungee Bracket

(BUNB18)

Bracket Cover

(BC18)

Bracket Screws

(BSC18)

Bungee Screw

(BUNSC18)

Bungee Anchor

(BUNA18)

Pole

(HP18)

Tools required: phillips screwdriver, leveling device (laser level, standard level, etc.), and

power drill (if pre-drilling the holes).

Your shade is prepared for a wall installation, with

the Crank Bracket on the right side of the shade.

See Figure N for the default bracket conguration.

If you require the Crank Bracket on the left of the

shade, or if you require a ceiling installation (or

both), you will need to make a small change to your

brackets.

www.shadeinfo.com

Note: your parts and fabric may differ in color than shown in this manual

To change your brackets, remove both Bracket Covers (Fig O). Remove the 2 screws from

the Crank Bracket (Fig P) and the 3 screws from the Plug Bracket (Fig Q).

After removing the screws from both brackets, rotate the hardware to match your install

type (Fig R, Fig S and Fig T below).

Important: if you move your Crank Bracket to the left side of your shade, you will need to

remove and reverse the locations of your Crank Plug and Plug with Pin to match the

corresponding bracket. These plugs are pre-installed inside of your top tube

(not illustrated).

If you move your crank to the left of the shade, you will need to change the roll direction

of your fabric to prevent the fabric from interfering with the crank ring. To reverse the roll

direction of your fabric, simply roll the shade down completely. After the fabric is

completely lowered, continue rolling the shade...it will roll itself up in the opposite

direction.

(DEFAULT SETUP)

Summary of content (2 pages)

PAGE 1
Ceiling Mount or Left Crank Operation (or both) Your shade is prepared for a wall installation, with the Crank Bracket on the right side of the shade. See Figure N for the default bracket configuration. If you require the Crank Bracket on the left of the shade, or if you require a ceiling installation (or both), you will need to make a small change to your brackets.
PAGE 2
Your shade can be installed against a wall (Fig B) or against a ceiling/overhang (Fig C). WALL MOUNT CEILING MOUNT Step 3: Install solar shade To install your shade, start by attaching the Crank Plug into the Crank Bracket (Fig G). Next, slide the Plug with pin into the Plug Bracket. Note: the Plug (with pin) should slide and click into the Plug Bracket (Fig H). Figure B Figure C Your shade is already prepared for a wall mount, with the crank on the right side of the shade.