Operation Manual

39
!
Dust Bag
Part No 5093 ER
Micro Filter
Part No 5036 ER
Exhaust Filter
Part No 5143
Brush Roller
(X4 / X1.1)
Part No 5010 ER
Figure 7
Figure 8
Figure 9
Figure 10 (X1.1 / X4)
Figure 10a (X5)
Sealing Strip
Part No 5400-1
(X1.1 / X4)
Part No 5400-2 (X5)
Brush & Edge Rollers ( X5)
Part No 5290 ER
Figure 11 (X1.1 / X4)
Figure 11a (X5)
Maintenance
Always unplug vacuum from socket
before handling!
Changing the Dust Bag-Figure7
Tochangethedustbag,pullthecoverreleaseflapfor-
ward(#5onpage5)andliftthecover(7)fromthedust
baghousing.The cover release flap must remain in a
forward „pulled-out“ position to change dust bags and
lock them into place.Squeezetheclampsonbothsides
ofthedustbagsealingplate,slidetheplate(28)fromthe
holder(29)andpushthecapontosealthebag.Slidethe
sealingplate(28)ofanewbagintotheholderandpush
itinfirmly.Re-insertcoverintodustbaghousing,pushit
forward,thenlockitinplacebypushingdownthecover
releaseflap.Youmayfinditconvenienttostorethebag
capinsidethedustbaghousingbelowthedustbag.
Changing the Micro Filter - Figure8
The microfilter (30)needstobechangedwhenit be-
comesextremelydirtyorcloggedwithdust,orwhenap-
proximately20dustbagshavebeenused.Tochangethe
microfilter,pullthecoverreleaseflap[#5onpage5)for-
wardandliftthecoverfromthedustbaghousing.Then,
slidethefilteroutatthebottom.Toreplace,liftthesafety
lever(31)andslidethenewfilterinusingthetracksas
guides.
Changing the Exhaust Filter -Figure9
When20bagshavebeenused,changetheexhaustfil-
ter(32).Toremovetheexhaustfilter,pushthecatch(33)
backwardandremovethefiltercover(34)andexhaust
filter.Insertthenewfilterandreplacethefiltercover.
Changing the Brush Roller(s) -
Figure10(X1.1/X4),Figure10a[X5
)
To remove the brush roller[s) (35 or 35a), push the
button(s)(36or36a),removethesideplate(s)(37or37a),
turnthebrush[s)clockwiseaquarterofaturn,andpull
theoldbrushroller(s)out.Slidethenewbrushroller(s)
intothebrushhousingandturnituntilitlocksintopo-
sition.Whileslightlypushingthe button[s)[36or36a),
pressthesideplate(s)(37or37a)backintothelocked
position.
Changing the Sealing Strip -
Figure11(X1.1/X4).Figure11a(X5)
The sealing strip (39)islocated just behind thebrush
rolleropening.Thesealingstripsealsthepowerhead
tohardfloorstopreventkick-backofdebriswhilevacu-
uming.Toreplaceawornsealingstrip,pushtherelease
button,removethesideplate(36and37infigure10&
10a)andslideoldstripout.Insertthenewstripintothe
slotandslideintoplace.
Page9