Detector Installation Manual

ManualsBrandsSECO-LARM USA ManualsHome Safety ProductENFORCER 190S

OPERATING THE ENFORCER 190 / 190S

MOUNTING THE DETECTOR

It therefore should be mounted in a location within which every glass

window and door to be protected is found. For greatest security, attach to

the wall or ceiling, using screws instead of double-sided foam tape. For

larger areas, two or more units can be used without fear of interfering with

each other.

SETTING THE SENSITIVITY

The ENFORCER 190/190S includes SECO-LARM's unique patented

Yellow turbulence LED. This LED flashes when environmental noise is high

enough to cause false alarms, thereby allowing instant sensitivity setting

without the use of a special external test meter.

To set sensitivity, hold a thin flexible plastic ruler flat against a glass

window within the unit's protection range.

Pick up one end of the ruler while holding

the other end down, and then let the ruler

snap against the glass window. This

should cause the Yellow LED to come ON,

but the Red LED should not light. If the

Red LED comes ON with a slight snap, the

ENFORCER 190/190S may be too

sensitive, and the sensitivity control should

be turned counterclockwise with a small

flat or phillips screwdriver. If the Yellow

LED does not come ON, sensitivity should

be increased by turning the control clockwise. Continue snapping the ruler

on the window until the Yellow LED comes ON but the Red LED does not.

Repeat this process with each window to ensure the ENFORCER 190/

190S is set for every pane of glass.

When the correct sensitivity is found using the above procedure, determine

whether the sensitivity is high enough to trigger the alarm by snapping the

ruler harder to simulate a break-in. If the Red LED does not come ON, the

sensitivity must be increased.

NOTE: For applications within this temperature range the sensitivity will be

stable. If the temperature should drop below -14°F (-10°C), the

sensitivity of the ENFORCER 190/190S will increase, and the

sensitivity setting will need to be decreased. If the temperature

should rise above 122°F (50°C), the sensitivity of the

ENFORCER 190/190S will decrease, and the sensitivity setting will

need to be increased.

When setting sensitivity, make sure the room's environment is as close as

possible to what it will be when the ENFORCER 190/190S is in use. For

instance, if the curtains are usually closed at night when the alarm is

armed, then set sensitivity with the curtains closed. If a window in the

room is left opened, then set the sensitivity with window open. The

sensitivity should always be retested when the environment of the room

changes, such as when furniture is moved.

Depending on the type of glass, sensitivity is different when set by tapping

the inside or outside of the window with a ruler. For best results,

tap the inside of the window.

NOTE: DO NOT SET SENSITIVITY ANY HIGHER THAN NECESSARY TO

PROTECT THE GLASS IN THE DETECTOR'S RANGE. SETTING

SENSITIVITY HIGHER THAN NEEDED INCREASES THE

CHANCE OF FALSE ALARMS WITHOUT INCREASING

PROTECTION. LEAVING A DOOR OR WINDOW OPEN WILL

ALSO INCREASE THE CHANCE OF FALSE ALARMS.

TAMPER-PROOFING CASE

For extra protection, the ENFORCER 190/190S is equipped with an

N.C. Tamper Switch to protect against opening or breaking of the

case.

INSTALLATION

SCREW TERMINALS:

MIN MAX

#7: N.C. TAMPER OUTPUT

#6: COMMON TAMPER OUTPUT

#5: COMMON GROUND

#4: 12VDC

#3: DRY RELAY N.O.*

#2: DRY RELAY COMMON*

#1: DRY RELAY N.C.*

* For N.O. output, use Terminals 2 and 3

For N.C. output, use Terminals 2 and 1

Summary of content (2 pages)

PAGE 1
OPERATING THE ENFORCER 190 / 190S MOUNTING THE DETECTOR It therefore should be mounted in a location within which every glass window and door to be protected is found. For greatest security, attach to the wall or ceiling, using screws instead of double-sided foam tape. For larger areas, two or more units can be used without fear of interfering with each other. SETTING THE SENSITIVITY The ENFORCER 190/190S includes SECO-LARM's unique patented Yellow turbulence LED.
PAGE 2
SECO-LARM ENFORCER  190/190S INSTALLATION HINTS GLASS BREAK DETECTOR 1. The ENFORCER 190/190S usually receives power from the alarm panel. If the ENFORCER 190/190S is connected to a separate power source, it should also be connected to a rechargeable battery, in case AC power fails. 2. Use either Terminals 2 and 3 N.O. output or 2 and 1 for N.C. output, but not both. 3. Close all doors and windows when the ENFORCER 190/190S is in use. 4.