EV-7105-NPEQ (NTSC) EV-7105-PPEQ (PAL) Mini PTZ Camera Manual • • • • 10x Optical zoom and 10x digital zoom Up to 100x zoom Up to 360°/sec pan/tilt motion Outdoor or indoor use • • Up to 127 preset target views, each with its own characteristics such as white balance and auto exposure Up to 95° tilt, up to 180° with auto-flip Note: Model numbers that end with “Q” or products that have a round green “Q” sticker signify RoHS compliance.
ENFORCER Mini PTZ Camera a Table Contents Table ofofContents Introduction 2 SYSTEM INFORMATION Menu 18 Features and Functions 3 DISPLAY SETUP Menu 19 Parts List 4 SET NORTH DIRECTION Menu 19 Specifications 4 PRIVACY ZONE Menu 20 Dimensions 5 EDIT MASK Menu 20 Safeguards and Precautions 6 DOME CAMERA SETUP Menu 21 Overview 7 ZOOM CAMERA SETUP Menu 22 Communication Protocol and Camera ID 8 WB SETUP Menu (White Balance) 22 Installation 9 AE SETUP Menu (Auto Exposure) 23 Con
ENFORCER Mini PTZ Camera ENFORCER Mini Camera and Functions EV-7105-NPE PTZPTZ Camera FeaturesFeatures and Functions 1/4-inch CCD camera with Day and Night 1function, up to 100X zoom (max. 10X Powerful yet flexible Powerful and Flexible: The camera: ENFORCER Mini PTZ Camera is equipped with a /4-inch CCD, a powerful Day and Night optical 10X digital focus and fullmultiple programmability. function, up tozoom 100x and zoom (max.
ENFORCER Mini PTZ Camera a Parts List: 1x Camera Video Signal System 1x Wall-mount bracket Camera CCD 1x Manual Max. Pixels Effective Pixels Horizontal Resolution Specifications: S/N Ration Zoom Focal Length Type Min.
ENFORCER Mini PTZ Camera Dimensions: Camera Side Bottom 6” (152mm) 7” (180mm) 413/16” (122mm) Wall-Mount Bracket Side Bottom 31/8” (80mm) 411/16” (119mm) 61/2” (166mm) SECO-LARM, U.S.A., INC.
ENFORCER Mini PTZ Camera Safeguards and Precautions Before Starting: 1. 2. 3. 4. 5. 6. 7. 8. 9. Please read this manual carefully and keep it for future reference. Use the camera within given temperature and electrical limits. Do not point the camera at the sun. Heat could damage the camera, even when not in use. Do not expose the camera to rain or moisture. Do not install the camera in dusty or humid environments.
ENFORCER Mini PTZ Camera a Overview Wall mount bracket Camera DIP switches Lens Turn counter-clockwise to remove Dome SECO-LARM, U.S.A., INC.
ENFORCER Mini PTZ Camera a Communication Protocol and Camera ID DIP Switch Setup: Before the Mini PTZ Camera is installed, first set up the DIP switches to configure the camera ID and the communications protocol. Communication Protocol Camera ID 1. Remove the clear dome of the Mini PTZ Camera by turning it counterclockwise by hand. 2. Look for the two DIP switch blocks near the base of the black plastic dome which surrounds the camera. DO NOT REMOVE THE BLACK PLASTIC DOME. 3.
ENFORCER Mini PTZ Camera a Installation 1. Connect the camera to either the included wall mount or other optional bracket. 2. Run a 24VAC power supply wire, a video cable with a male BNC connector, and a data wire through the wall to where the camera is to be mounted. 3. Connect the camera's video cable to the video cable coming from the wall. Do not cut the female BNC connector of the camera's video cable as that will void the warranty. 4.
ENFORCER Mini PTZ Camera a Pre-operation Checklist Before operating this PTZ camera, please note the following: Double-check that the cables are properly run between the controller and camera, and that all connections are correct. Double-check that the camera ID on the controller is the same as the ID of the target camera. The camera ID can be found by looking at the camera ID DIP switch settings (see page 8). The Pelco protocol setting of the controller and the camera must be identical.
ENFORCER Mini PTZ Camera Understanding and Operating Preset and Pattern Functions Standard Pelco-compatible controllers allow the camera operator to do several functions without going through the full OSD menu, depending on the capabilities of the DVR to which the camera is connected. The SECO-LARM series of DVRs allows operators to do the following via the "Dome Preset" menu: • Set the camera to remember multiple specific preset locations. • Tell the camera to go to a specific preset location.
ENFORCER Mini PTZ Camera Configuring Mini PTZ Camera settings with an ENFORCER DR-1 Series DVR Step 1 Press Dome on the DVR front panel to access DVR controls. Step 2 Press 1 to access the DVR preset menu Step 3 Use the Up, Down, Left, Right, and Enter buttons to make a selection. Step 4 Go to Preset 95 to access Mini PTZ OSD settings. This will bring up the SPEED DOME CAMERA menu as shown on page 18. 12 SECO-LARM, U.S.A., INC.
ENFORCER Mini PTZ Camera Reserved Presets [95] [131~134] [141~148] [151~158] [170] [171] [174] [175] [176] [177] [178] [179] [190] [191] [192] [193] [194] :Enters into OSD menu :Runs Pattern Function 1~4 :Runs Swing Function 1~8 :Runs Group Function 1~8 :Sets Camera BLC mode to OFF :Sets Camera BLC mode to
ENFORCER Mini PTZ Camera OSD Display of Main Screen Preset Label Action Title Alarm Information Image Flip Camera ID Pan/Tilt/Zoom Information OSD Main Screen The OSD main screen shows information about the current situation of the camera while it is operating. This screen is NOT seen as part of the programming process. Preset Label Action Title Image Flip Camera ID Alarm Information P/T/Z Information 14 The label of the specific preset.
ENFORCER Mini PTZ Camera Operating the OSD Menus For operating the OSD menus, please note the following: • To access the OSD menu from your DVR, go to Preset 95. For more information on DVR presets and their functions for the ENFORCER Mini PTZ Camera, please see page 13, Reserved Presets. • Most commands are done on PELCO-compatible DVRs using the front panel keys, including the up, down, right, and left arrows, or via a panel-mounted joystick.
ENFORCER Mini PTZ Camera ENFORCER Mini PTZ Camera OSD (On-screen Display) and Programming Flowchart This chart shows all the screens used in programming the PTZ camera using the OSD. OSD Main Screen (page 14) To go to a particular screen, follow the order as shown in this flowchart. For more information on a particular screen, go to the page number listed on the screen.
ENFORCER Mini PTZ Camera SPEED DOME CAMERA Menu SPEED DOME CAMERA • : Displays system information and configuration (see menu on page 18). • : Configures the display information shown on the OSD Main Screen as shown on page 16 (see menu on page 19). EXIT • : Configures various functions of the camera (see menu on page 21).
ENFORCER Mini PTZ Camera DISPLAY SETUP Menu From SPEED DOME CAMERA DISPLAY SETUP CAMERA ID : ON PTZ INFORMATION : AUTO ACTION TITLE : AUTO PRESET LABEL : AUTO ALARM INPUT : AUTO BACK EXIT This menu enables or disables the information shown on the OSD Main Screen (see page 14). Note that setting an item to "AUTO" means that item will be displayed only when its value changes.
ENFORCER Mini PTZ Camera PRIVACY ZONE Menu From DISPLAY SETUP PRIVACY ZONE MASK NO DISPLAY CLEAR MASK 1 UNDEFINED OFF CANCEL This menu configures an area of the camera’s field of vision so that it is covered by a gray mask, hiding it. For instance, this would be used to cover a neighbor’s window, or a sensitive window of the office. Once configured, the gray mask automatically appears over that area every time the camera pans or tilts past it.
ENFORCER Mini PTZ Camera DOME CAMERA SETUP Menu From SPEED DOME CAMERA DOME CAMERA SETUP BACK EXIT SECO-LARM, U.S.A., INC. Goes to the ZOOM CAMERA SETUP menu for configuring many of the general functions of the zoom camera module. See page 22. Configures the general functions of the pan and tilt motions.
ENFORCER Mini PTZ Camera ZOOM CAMERA SETUP Menu From DOME CAMERA SETUP ZOOM CAMERA SETUP This menu configures many of the general functions of the zoom camera module. FOCUS MODE SEMI-AUTO DIGITAL ZOOM ON LINE LOCK OFF IMAGE FLIP OFF BACK EXIT FOCUS MODE DIGITAL ZOOM LINE LOCK IMAGE FLIP [AUTO / MANUAL / SEMI-AUTO] Sets the camera focus mode.
ENFORCER Mini PTZ Camera AE SETUP Menu (Auto Exposure) From ZOOM CAMERA SETUP BACKLIGHT AE SETUP - GLOBAL BACKLIGHT DAY/NIGHT BRIGHTNESS IRIS SHUTTER AGC SSNR SENS-UP BACK EXIT OFF AUTO 25 AUTO ESC NORMAL MIDDLE AUTO DAY/NIGHT BRIGHTNESS IRIS SHUTTER AGC SSNR SENS-UP SECO-LARM, U.S.A., INC. [ON / OFF] Sets the backlight compensation. [AUTO1 / AUTO2DAY / NIGHT] AUTO1 flips between the day and night modes faster than AUTO2. [0~100] Adjusts the brightness of the image.
ENFORCER Mini PTZ Camera MOTION SETUP Menu From DOME CAMERA SETUP Configures the general functions of the pan and tilt motions.
ENFORCER Mini PTZ Camera PARKING ACTION SETUP Menu From MOTION SETUP PARKING ACTION SETUP PARK ENABLE WAIT TIME PARK ACTION OFF 00:10:00 HOME This menu sets what the camera will do if it receives no PTZ command during a preset time. PARK ENABLE BACK EXIT WAIT TIME PARK ACTION [ON / OFF] If set to ON, the camera runs an assigned function automatically if there is no PTZ command during the configured "WAIT TIME.
ENFORCER Mini PTZ Camera PRESET MENU From DOME CAMERA SETUP PRESET MENU PRESET NO. 1 CLR PRESET CAM ADJUST CANCEL This menu configures up to 127 different preset locations to which the camera can be instantly moved. [1~94, 96~128] If the PRESET number has already been defined, the camera immediately moves to the pre-set PRESET position and characteristics. If not, "UNDEFINED" is shown on the screen GLOBAL BACK EXIT PRESET NO.
ENFORCER Mini PTZ Camera EDIT SCENE Menu From PRESET MENU EDIT SCENE – PRESET 1 This menu redefines the current PRESET scene position. 1. Use the joystick or arrow keys to move the camera to the desired position. 2. Press the "NEAR" key to save the new camera position, or press the "FAR" key to cancel this position.
ENFORCER Mini PTZ Camera SWING SETUP Menu From DOME CAMERA SETUP SWING SETUP SWING NO. 1ST POS. 2ND POS. 1 NOT USED NOT USED SWING SPEED CLEAR SWING 30/SEC CANCEL BACK EXIT EDIT LABEL – PRESET 1 SWING NO. 1ST POS. 2ND POS. 1 PRESET 5 NOT USED UNDEFINED This menu configures up to eight different swing motions back and forth between two different PRESET positions. When the SWING function operates, the camera moves (pans and tilts) to the PRESET position that was set as the "1ST POS.
ENFORCER Mini PTZ Camera PATTERN SETUP Menu From DOME CAMERA SETUP PATTERN SETUP PATTERN NO. 1 UNDEFINED CLR PATTERN CANCEL Configures up to four pan/tilt patterns, with each pattern consisting of a starting position, an ending position, and the complete pan/tilt/halt movement between those two points . PATTERN NO BACK EXIT CLR PATTERN [1 ~ 4] Selects which PATTERN number to edit.
ENFORCER Mini PTZ Camera GROUP SETUP Menu From DOME CAMERA SETUP GROUP SETUP GROUP NO. 1 UNDEFINED CLEAR GROUP CANCEL Configures up to eight groups of motions, with each group consisting of any combination of up to 20 actions, including PRESETS, SWINGS, PATTERNS, and temporary halts in the action. GROUP NO BACK EXIT CLR GROUP EDIT GROUP 1 1. Press the NEAR key on the "NO" line to start the GROUP setup. 2.
ENFORCER Mini PTZ Camera 4. EDIT GROUP 1 NO ACTION ### DWELL OPT 1 PRESET 1 00 : 03 : 360 2 NONE 3 NONE 4 NONE 5 NONE SAVE CANCEL Configure each ACTION, ###, DWELL, and OPT. In the sample screen on the left, ACTION #1 is the command for the PTZ camera to go to PRESET #1 using the PRESET speed of 360 as programmed in the PRESET SETUP menu (see page 26), and stay at that position for 3 seconds before moving to the next action. [◄►:MOVE CURSOR] [▲▼:CHANGE VAL.] EDIT GROUP 1 5.
ENFORCER Mini PTZ Camera Also Available from SECO-LARM: Ceiling Bracket Pole-Mounting Bracket Corner-Mounting Bracket Flush-Mount Bracket DR-1 Series Digital Video Recorder EV-7100CEILM EV-7100POLEM EV-7100CORNM EV-7100FLUSM DR-116-1.