Installation Manual

ENFORCER 33ft Polarized
Reflective Photoelectric Beam Sensor
4 SECO-
LARM U.S.A., Inc.
WARRANTY
This
SECO
-
LARM product is warranted against defects in material and workmanship while used in normal service
for a period of one (1) year from the date of sale to the original consumer customer. SECO-
LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO
-
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, r
or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-
LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive
remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-
LARM be liable for any special, collateral, incidental, or consequential personal
or property damages of any kind to the purchaser or anyone else.
NO
TICE:
The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-
LARM reserves the right to
change specifications without notice. SECO-
LARM is also not responsible for misprints or typographical errors.
Copyright © 2016 SECO-
LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
SECO
-
LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: [phone] Fax: [phone] E-mail: [e-mail]
Troubleshooting:
Sensor does not detect the object.
•
Change the angle of the sensor or readjust
the sensitivity setting.
The beam sensor LED will not turn green.
•
Clean the sensor and reflector with a damp
(not wet) cloth.
•
Adjust the reflector and/or sensor for proper
alignment.
Beam sensor LED lig
hts when object
is detected, but there is no output.
•
Check wiring between the sensor and local
alarm device.
Sample Applications:
Garage
Door
Gate
Vehicle
Detection
Other Sensors Available:
Dual and
Quad Beam
Optional Accessory:
Reflector Hood
E-931ACC-HR1Q
Provides extra
protection for the
reflector.
Compatible with Reflective Photoelectric Beam Sensor models
E-931-S50RRGQ, E-931-S35RRQ, and E-931-S33PRGQ.
Reflective
Photobeam
Reflective Photoelectric Beam Sensor
LARM U.S.A., Inc.
LARM product is warranted against defects in material and workmanship while used in normal service
LARM’s obligation is limited to the
-
LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, r
epair,
LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
remedy, shall be limited to replacement or repair only, at
LARM be liable for any special, collateral, incidental, or consequential personal
The information and specifications printed in this manual are current at the time of publication. However, the
LARM reserves the right to
LARM is also not responsible for misprints or typographical errors.
LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
MI_E
-
931
-
S33PRGQ_151218.docx
PITSW3
Change the angle of the sensor or readjust
the sensitivity setting.
Clean the sensor and reflector with a damp
Adjust the reflector and/or sensor for proper
Check wiring between the sensor and local
Assembly
Line
Other Sensors Available:
Dual and
Quad Beam
Curtain and
Barrier
E-931-S33PRGQ
33
ft
Polarized
Reflective Photoelectric
Beam Sensor
Manual
•
Polarized sensor is immune to
• shiny objects: Triggers only when
• correctly reflected light is detected.
• Weatherproof (IP55)
• Anti-condensation housing
• 12-30V DC/AC 60Hz, 100mA
•
Up to 33ft (10m) sensing range
• Round reflector, Dia.: 3
1
/
4
"
• Form C relay: 0.5A@30VAC/VDC
• Beam status LED
• N.C. Tamper switch:
500mA@30VAC/VDC
Caution:
• This sensor is not designed to prevent bodily injury or loss of life.
• This sensor is not designed for use in environments where explosive gasses may be present.
• Use of this sensor in certain security applications may be regulated by local laws or codes. SECO-LARM is not
responsible for compliance with such laws or codes.