VPD (Video/Power/Data) Combiners Manual (EB-P304-01MQ shown) (EB-C304-01EQ shown) Midpoint VPD Combiners: Model # EB-P304-01MQ EB-P316-60MQ EB-D304-01MQ* EB-D316-60MQ* EB-C304-01MQ* EB-C316-60MQ* Power Passive Passive 12VDC 12VDC 24VAC 24VAC Endpoint VPD Combiners: Channels 4 16 4 16 4 16 Model # EB-P304-01EQ* EB-P316-60EQ EB-D304-01EQ* EB-D316-60EQ* EB-C304-01EQ EB-C316-60EQ* Power Passive Passive 12VDC 12VDC 24VAC 24VAC Channels 4 16 4 16 4 16 *Special Order Only ENFORCER VPD (Video/Power/Data
ENFORCER VPD Combiners Table of Contents: Introduction ...................................................................................................................................... 2 Parts List .......................................................................................................................................... 2 Specifications .................................................................................................................................. 3 Overview ..........
ENFORCER VPD Combiners Specifications: Midpoint VPD Combiners Model # Type Channels EB-P304-01MQ EB-P316-60MQ EB-D304-01MQ* EB-D316-60MQ* EB-C304-01MQ* EB-C316-60MQ* Passive Midpoint 12VDC Midpoint 24VAC Midpoint 4 16 4 16 4 16 CVBS 984’ (300m) HD-AHD 720p: 1050’ (320m); 1080p: 722’ (220m) Video range HD-CVI 720p: 1476’ (450m); 1080p: 820’ (250m) HD-TVI 720p/1080p: 820’ (250m) Video format NTSC, PAL, SECAM Maximum input 1Vp-p Frequency response DC to 60MHz CMMR 60dB , 20kHz~60MHz Wire category CAT5e~CAT6
ENFORCER VPD Combiners Overview: Passive Midpoint VPD Combiners: NOTE: EB-P304-01MQ shown. EB-P316-60MQ has similar connections, but has 16 channels. Video/Power/Data RJ45 (to camera VPD balun) Video RJ45 (to DVR video balun) Data RJ45 (to RS-485 controller) Power Status LEDs Active Midpoint VPD Combiners: Power Input Terminals (12/24 VAC/VDC) NOTE: EB-D304-01MQ shown. EB-C304-01MQ has similar connections. EB-D316-60MQ and EB-C316-60MQ have similar connections, but have 16 channels.
ENFORCER VPD Combiners Dimensions: Passive VPD Combiners: NOTE: EB-P304-01MQ and EB-P316-60MQ shown. EB-P304-01EQ and EB-P316-60EQ have the same dimensions (respectively). . 13/4” (44mm) 65/16” (160mm) 15/16” (33mm) 13/4” (44mm) 1615/16” (430mm) 15/16” (33mm) 12VDC VPD Combiners: NOTE: EB-D304-01EQ and EB-D316-60EQ shown. EB-D304-01MQ and EB-D316-60MQ have the same dimensions (respectively). .
ENFORCER VPD Combiners Installation: 1. Location: Install the unit in a ventilated, dry location where it will not be disturbed by other activities. A data center room is ideal. NOTE: For indoor use only. Make sure there is a cool air flow around the unit to prevent it from overheating. a. Install the Passive Midpoint VPD Combiners near the power supply at a point between the cameras and DVR. b. Install the Active Midpoint VPD Combiners at a point between the cameras and DVR.
ENFORCER VPD Combiners Power Range: Use this chart to determine the maximum distance between the VPD Combiner and the cameras when powering cameras at extended distances.
ENFORCER VPD Combiners Wiring the Passive Midpoint VPD Combiners (EB-P304-01MQ and EB-P316-60MQ): 1. Connect cameras to VPD baluns (such as the EB-P101-20VQ) and run them via CAT5e/6 to the “Camera” ports on the VPD Combiner. 2. Run 12 or 24 VDC power to the “Power In” press-fit terminals on the VPD Combiner, depending on each camera’s power requirements. For each camera port connected to the VPD balun, the corresponding power input must be connected to power. NOTE: Observe polarity when connecting power.
ENFORCER VPD Combiners Wiring the Active Midpoint VPD Combiners (EB-D304-01MQ, EB-D316-60MQ, EB-C304-01MQ and EB-C316-60MQ): 1. Connect cameras to VPD baluns (such as the EB-P101-20VQ) and run them via CAT5e/6 to the “Camera” ports on the VPD Combiner. 2. Run a CAT5e/6 cable from the “Video Out” port on the VPD Combiner to baluns or a multiplechannel passive video transceiver on the DVR side. NOTE: Consult the balun or video transceiver manual for range information. 3.
ENFORCER VPD Combiners Wiring the Passive Endpoint VPD Combiners (EB-P304-01EQ, EB-P316-60EQ): 1. Connect cameras to VPD baluns (such as the EB-P101-20VQ) and run them via CAT5e/6 to the “Camera” ports on the VPD Combiner. 2. Run 12 or 24 VDC power to the “Power In” press-fit terminals on the VPD Combiner, depending on each camera’s power requirements. For each camera port connected to the VPD balun, the corresponding power input must be connected to power. NOTE: Observe polarity when connecting power. 3.
ENFORCER VPD Combiners Wiring the Active Endpoint VPD Combiners (EB-D304-01EQ, EB-D316-60EQ, EB-C304-01EQ and EB-C316-60EQ): 1. Connect cameras to VPD baluns (such as the EB-P101-20VQ) and run them via CAT5e/6 to the “Camera” ports on the VPD Combiner. 2. Run coaxial cables from the BNC ports on the VPD Combiner to the BNC ports on the DVR. 3. Run a CAT5e/6 cable from the “Data Out” port on the VPD Combiner to the DVR or PTZ Controller. Sample Installation: NOTE: EB-D304-01EQ shown.
ENFORCER VPD Combiners Troubleshooting: Wavy or ghost image if connected to image processor (e.g., multiplexer or DVR), but not if directly to monitor. Image is wavy and shakes. Image is weak or faded. No image. PTZ Controls do not work. Power LEDs are OFF Move the Cat5e/6 cable away from possible sources of interference. Ensure that the same twisted pair connects to a balun at both ends of the cable. Replace the cable with a new Cat5e/6 cable.
