User Manual

ENFORCER Passive Video Baluns
4 SECO-LARM U.S.A., Inc.
MiEB-P501-xxQ_1302.docx
PITSW4
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and
recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
The SECO-LARM UL Listed Baluns with surge protection are to be used with other UL Listed Audio/Video product.
T
The
WARNING
Incorrect mounting which leads to exposure to rain or moisture inside the enclosure could cause a dangerous electric shock, damage the device, and void the
warranty. Do not open the case of this device, as there are no field-serviceable components inside.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and
improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or
typographical errors.
Copyright © 2013 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of
SECO-LARM.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone] Fax: [phone]
Website: www.seco-larm.com
E-mail: [e-mail]
The image is wavy, shakes, or ghosts.
There is no image.
 Reduce cable length.
 Replace cable with higher grade cable.
 Install an ENFORCER Ground Loop Isolator (VG-1C12BQ).
 Install an ENFORCER Video Amplifier (VA-2101B-WQ).
 Check the power supplies of all devices connected.
 Double-check that the cable was connected properly.
 Connect a test monitor directly to the camera. If there is still no
video, troubleshoot the camera and its power supply.
Troubleshooting:
Specifications:
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for the life of the product from the date
of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to
SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or
abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than
defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the
purchaser or anyone else.
Video
Range*
B/W
1,950’ (600m)
Color
1,300’ (400m)
Video format
PAL, NTSC, SECAM
Maximum input
1Vp-p
Insertion loss
<2dB per pair from DC~6MHz
Return loss
>18dB from DC~6MHz
Frequency response
DC~6MHz
Common mode rejection
60dB, 15kHz~6MHz
Connections
Wire type
UTP (Unshielded Twisted Pair) 24~16 AWG
Wire category
Cat2 min.
UTP Connection
Gold plated
Attenuation
DC~6MHz, 2dB max.
Impedance
Coax, male BNC
75Ω@1MHz
Terminal block
100Ω@1MHz
Other
DC Loop resistance
52Ω/1000’ (18Ω/100m)
Differential capacitance
19pF/ft max. (62pF/m max.)
Power
No power required
Max. amperage
EB-P501-02Q, EB-P501-02SQ, EB-P501-21Q, and EB-P501-21SQ Only
3A@12VDC, 1.5A@24VAC
Operating temperature
32~131 F (0~55 C)
Storage temperature
-4~185 F (-20~85 C)
Humidity range
0~95% (Non-condensing)
Case
ABS Plastic
*Shorter range may result when used with a DVR.
Made in Taiwan