Manual

ENFORCER IP Wall-Plate Camera
4 SECO-LARM U.S.A., Inc.
The screen is blank
 Check that the camera is powered up
 Check that the power supply's polarity is correct
 Check that the monitor is powered up
 Check that the video cable connecting the camera to
the monitor is connected properly
 Verify video format
The screen image is dim
 Clean the lens using a soft, clean cloth
 Change the position of the camera
 Verify video format
The screen image has poor contrast
 Adjust the monitor's contrast knob
 Change the position of the camera
 Verify video format
The screen image flickers
 Change the position of the camera
 Verify video format
The
camera case is hot
 Check that the correct power supply is in use
Troubleshooting:
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: [phone] | [phone] Email: [e-mail]
PIKSR1
MI_EV-N5205-3S4Q_200918.docx
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-
LARM reserves
the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All t
rademarks are the
property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM U.S.A., Inc.
All rights
reserved.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while
used in normal
service for three (3) years from the date of sale to the original customer. SECO-
LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if
damage is caused by or attributed to ac
ts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper
or abnormal usage, or faulty installation, or if for any other reason SECO-
LARM determines that such equipment is not
operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-
LARM
and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option.
In no event
shall SECO-LARM be liable for any special, collateral, i
ncidental, or consequential personal or property damage of any kind
to the purchaser or anyone else.
IMPORTANT:
Users and installers of this product are responsible for ensuring this product complies with all national, state,
and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM
will not be held
responsible for the use of this product in violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2)
THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for complia
nce could void the user’s
authority to operate the equipment.
IMPORTANT NOTE
: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the
device exceeding the RF exposure
requirements and void user’s authority to operate the device.
IMPORTANT WARNING: For a weather-
resistant installation, ensure that the unit is installed in a waterproof back box, and
that the faceplate and faceplate screws are properly sealed. Incorrect mounting may lead to exposure to rain or moisture in
the enclosure which could cause a
dangerous electric shock, damage the device, and void the warranty. Users and installers
are responsible for ensuring that this product is properly installed and sealed.