User Manual

ManualsBrandsSECO-LARM ManualsAlarm KitsComplete Wireless Alert System

RA-4961-K1Q

Wireless Alert System

Manual

Features:

• Up to 1,000ft (305m) transmission range*

• 18 Programmable ringtones

• Connect up to 4 wireless transmitter

accessories

• Audible and visual alert via built-in

speaker and flashing light

• Wall or desktop mountable

• Output terminals for optional auxiliary

device

• Each channel independently

programmable

* Transmission range will vary depending on installation and operating environment.

Kit Includes:

• Wireless Receiver (RA-4961Q) • Wireless Pushbutton (RA-4961-PBQ)

Summary of content (8 pages)

PAGE 1
® RA-4961-K1Q Wireless Alert System Manual Kit Includes: • Wireless Receiver (RA-4961Q) • Wireless Pushbutton (RA-4961-PBQ) Features: • Up to 1,000ft (305m) transmission range* • 18 Programmable ringtones • Connect up to 4 wireless transmitter accessories • Audible and visual alert via built-in speaker and flashing light • Wall or desktop mountable • Output terminals for optional auxiliary device • Each channel independently programmable * Transmission range will vary depending on installation and ope
PAGE 2
CBA Wireless Alert System Table of Contents: Dimensions ............................................2 Pairing Accessories ............................... 6 Parts List ................................................3 Deleting Paired Accessories ................. 7 Specifications ........................................3 Changing the Ringtone and Volume ..... 7 Overview ................................................4 Setting the Notification Mode ................ 7 Installing the Receiver ........
PAGE 3
CBA Wireless Alert System Parts List: 1x Wireless alert receiver (RA-4961Q) 1x Wireless pushbutton (RA-4961-PBQ) 1x Manual 1x CR2032 battery for wireless pushbutton (RA-4961Q batteries not included) Specifications: Receiver (RA-4961Q) Model number Frequency Channels Accessories per channel Relay output (Channel 4 only) Power supply Current Standby draw Max Estimated battery life Receiver low battery indicator Accessory low battery indicator Sound level (dB) Operating temperature Dimensions RA-4961Q 914.
PAGE 4
CBA Wireless Alert System Overview: Receiver Front (Cover off) Speaker Notification light Channel notification Open the front cover. Volume control Channel select button Tone select button Battery compartment Side Rear Reset button 6VDC Input RESET Notification selection switch Pushbutton Front (Cover on) Relay Wiring switches terminal Mounting holes Front (Cover off) Pushbutton Activation LED Battery holder 4 SECO-LARM U.S.A., Inc.
PAGE 5
CBA Wireless Alert System Installing the Receiver: 1. Open the front cover of the receiver unit. 2. Determine how the receiver will be powered. Either insert three "C" batteries (observing correct polarity, not included) or connect to 6VDC power supply (not included). Low battery is indicated when the notification light flashes once every 5 seconds. 3. Program pushbutton and any other accessories (see Pairing Accessories pg. 6). 4.
PAGE 6
CBA Wireless Alert System Replacing the Pushbutton Battery: 1. Remove the front cover of the pushbutton by inserting a paperclip in the notch at the top of the unit. Push down on the paperclip with force and pull the top of the front cover from the pushbutton. 2. If there is a previous battery installed, use a fingernail or small object to remove the battery from the battery holder. 3. Slide a CR2032 battery into the battery holder, making sure to observe correct polarity (positive faces out). 4.
PAGE 7
CBA Wireless Alert System Deleting Paired Accessories: 1. Enter programming mode by holding down the channel select button until the Channel 1 LED flashes on the channel notification panel. 2. Press the channel select button to cycle through channels until the desired channel is selected. 3. Press and hold the channel select and tone select buttons simultaneously until a beep is heard and the channel LED flashes. Press channel select button to exit pairing mode.
PAGE 8
CBA Wireless Alert System Wiring an Auxiliary Device: 1. 2. 3. 4. To connect an auxiliary notification device to channel 4, flip the left (relay) switch to "ON". Flip the right (time) switch to 2 for a 2-second activation time or 5 for a 5-second activation time. Wire the auxiliary device to the wiring terminal according to the diagram below. When channel 4 is activated, the auxiliary device will also be triggered. TERMINALS N.C. COM N.O.