Outdoor Stand-Alone Weatherproof Keypads Manual (SK-2323-SDQ shown) Model Number (SK-1323-SPQ shown) 2 Relay Outputs Backlit Keys Proximity Reader Mullion-Style Keypads SK-2323-SDQ SK-2323-SPQ Sealed-Environment Keypads SK-1323-SDQ SK-1323-SPQ NOTE: Products with a model number that ends with “Q” or have a round green “Q” sticker represent RoHs compliant products.
ENFORCER Outdoor Stand-Alone Keypads Table of Contents Features ........................................................ 2 Specifications ................................................ 2 Also Available from SECO-LARM ................. 2 Dimensions.................................................... 3 Parts List ....................................................... 3 LED & Audible Indicators .............................. 3 Optical Tamper ..............................................
ENFORCER Outdoor Stand-Alone Keypads Dimensions 15/16” SK-2323 Series 6” (152mm) SK-1323 Series 13/4” (44mm) (24mm) 7/8” 39/16” (90mm) 35/16” (84mm) 3” (76mm) (22mm) 39/16” (90mm) 43/4” (120mm) 35/16” (84mm) 2” (50mm) 13/16” (30mm) Parts List 1x Keypad 1x Manual 4x Mounting screws 4x Screw anchors 1x Security screw 1x Torx wrench 1x Mounting template 1x Metal oxide 1x Diode varistor (MOV) LED & Audible Indicators Left LED OFF OFF Green Red Green Red Orange Orange Green flashing OFF Righ
ENFORCER Outdoor Stand-Alone Keypads Important Notes ! IF USING THE KEYPAD WITH A MECHANICALLY OPERATED DOOR OR GATE, MOUNT THE KEYPAD AT LEAST 5’ (15m) FROM THE DOOR OR GATE TO PREVENT USERS FROM BEING CRUSHED OR PINNED. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. ! 1. Always disconnect power before servicing the keypad. 2. The keypad must be properly grounded. Use a minimum 22AWG wire connected to the Uninsulated Chassis Ground wire. Failure to do so may damage the keypad. 3.
ENFORCER Outdoor Stand-Alone Keypads Installation SK-2323 Series Mounting screws Mounting bracket Single-gang box mounting point Keypad Single-gang box mounting point Mounting screws Security screw SK-1323 Series Mounting screws Mounting bracket Single-gang box mounting point Keypad Single-gang box mounting point Mounting screws Security screw 1. Find a suitable location to mount the keypad. Do not install where it will be too high or too low for most users to operate the keypad. 2.
ENFORCER Outdoor Stand-Alone Keypads Sample Wiring and Application (SK-1323 series shown. All examples apply to both the SK-1323 and SK-2323 series.) Note: Sample applications are based on VDC power supplies. Connection to Lock Device and Alarm System Arm/Disarm Control Red—12~24 VAC/VDC (+) Pink—Output #1 (COM) 12~24 VAC/VDC Power Supply Black—12~24 VAC/VDC (-) Green—Common ground (-) Orange—Egress Input 1 (N.O.) Egress Button Yellow—Egress Input 2 (N.O.
ENFORCER Outdoor Stand-Alone Keypads Door Sensing N.C. Dry Contact Brown—Door Sensing Green—Common ground (-) Shunting an Alarm N.C. Zone N.C. Dry Contact Purple—Output #2 (COM) Alarm Control Panel Blue—Output #2 (N.O.) Door-Hold-Open Code Output #1 and Output #2 can be wired together in such a way that electric lock devices remain unlocked as long as Output #2 is activated. For N.C. Locking Devices Electric Strike Aqua—Output #1 (N.C.) Pink—Output #1(COM) Gray—Output #2 (N.C.
9 User Name SAMPLE – John Doe Access Code 54321 USER ID User Name Access Code USER ID 00 01 02 03 04 User Name USER ID 05 06 07 08 09 User Name Note: Copy this sheet to use for your installations. Access Code Access Code Output #2: Doorbell / Toggle / Timed (___secs.) Programmed For_______________________________ USER ID 001 Output #1: Toggle / Timed (___secs.
ENFORCER Outdoor Stand-Alone Keypads Programming Instructions 1. Codes are programmed to have 2~6 digits in length. All codes must be the same length. 2. Before inputting any of the following, enter Programming Mode by entering the Master Code twice. The default Master Code is 1234. To enter Programming Mode, enter 1 2 3 4 1 2 3 4 3. To exit Programming Mode, press the # key. 4. The keypad will exit Programming Mode if no keys are pressed for 30 seconds.
ENFORCER Outdoor Stand-Alone Keypads D. Program the Master Card (SK-1323-SPQ and SK-2323-SPQ only) In addition to a Master Code, a Master Card can also be programmed. Swiping a Master Card will give direct access to Programming Mode. 1. Enter Programming Mode by entering the Master Code twice. (Default Master Code is 1234) 7 . 3. On the keypad, enter 2. If the left LED is solid green and the right LED is flashing orange, a Master card is already programmed. Clear it by entering .
ENFORCER Outdoor Stand-Alone Keypads Continued from page 11. C. User Card and Code* 1. Enter a user ID number. ( 0 0 0 to 9 9 9 ) 2. If the left LED is red, previous user data exists. Clear it by entering confirmation and the left LED will turn green. 3. Swipe a new user card. 4. Enter a new user code. 5. To program the next user, repeat from step 1 in section A, B, or C. 6. Exit Programming Mode by pressing . .
ENFORCER Outdoor Stand-Alone Keypads Deleting or Changing an Output #1 User Step 1 Enter a user ID number. 0 0 0 to 9 9 Step 2 Delete existing user by entering: 9 Step 3 Swipe a new user card.* or Enter a new user code. X X X or Return to Programming Mode by entering This option deletes Output #1 users one at a time. To delete all users, see page 14, Deleting All Users. X Deleting or Changing an Output #2 User Step 1 Enter: 4 Step 2 Enter a user ID number.
ENFORCER Outdoor Stand-Alone Keypads Resetting the Keypad NOTE: Resetting the keypad will cause some or all programmed data to be lost. Do not perform either of these steps unless it is absolutely necessary. Deleting All Users Enter: 8 8 8 IMPORTANT: Once key entry is made, all user codes and user cards will be deleted and the keypad will return to Programming Mode. The Master Code and all other programming settings will remain the same. To restore factory settings, see Restore Factory Settings below.
ENFORCER Outdoor Stand-Alone Keypads Using the Keypad For programming instructions, see page 10, Programming Instructions. Entering a User Code To activate either Output #1 or Output #2, enter the user code directly into the keypad. Do not enter the user ID number. The user ID number is only used during Programming Mode. Example: If a user code for Output #1 is 4321, enter 4 3 2 1 to trigger Output #1.
ENFORCER Outdoor Stand-Alone Keypads Quick Reference Guide Note: For complete programming instructions, please see page 10, Programming Instructions.
