User Manual

ManualsBrandsSECO-LARM ManualsWireless Transmission2-Channel Receiver

This manual covers only one- and two-channel receivers. For information four-channel receivers, please contact SECO-LARM.

Installation Manual

One- and Two-Channel RF Receivers

The SK-910RBQ and SK-910RB2Q are wireless receivers that meets the growing demand for

receivers with multiple and independently controlled output functions. These RF receivers are

compatible with both code hopping and fixed code transmitters (see page 4 of this manual for a list of

compatible transmitters). The receivers can be used to control a variety of home automation devices

such as garage door openers, lights, motorized gates, lifts, or other devices remotely.

1. Mount the receiver out of sight in a location where it is not exposed to weather or moisture, and

where it is not surrounded by metal. Metal will block the RF signal, resulting in a reduced range.

2. For best range, pull the antenna wire as long and straight as possible. If the receiver receives

interference from local RF activity (e.g., an airport or military base), the antenna wire can be folded.

IMPORTANT: DO NOT CUT THE ANTENNA WIRE.

Installation Notes:

Introduction:

SK-910RBQ (315MHz)

SK-910RB-4Q (433.92MHz)

SK-910RB2Q (315MHz)

SK-910RB2-4Q (433.92MHz)

Flexible operating voltage: 11~24 VAC/VDC

Up to 500ft (152m) range

Independently programmable channels

Also Available from SECO-LARM:

Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.

SK-910RLQ ........................................... Low-voltage, one-channel receiver, 315MHz

SK-910RVQ ......................................................... Low-voltage, one-channel receiver,

transistor ground output 315MHZ

SK-910RL-4Q ................................... Low-voltage, one-channel receiver, 433.92MHz

SK-910RV-4Q ...................................................... Low-voltage, one-channel receiver,

transistor ground output, 433.92MHz

SK-910RB2Q shown

Summary of content (4 pages)

PAGE 1
Installation Manual SK-910RBQ (315MHz) SK-910RB-4Q (433.92MHz) SK-910RB2Q (315MHz) SK-910RB2-4Q (433.92MHz) SK-910RB2Q shown One- and Two-Channel RF Receivers Flexible operating voltage: 11~24 VAC/VDC Up to 500ft (152m) range Independently programmable channels Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant. Also Available from SECO-LARM: SK-910RLQ ...........................................
PAGE 2
ENFORCER Two-Channel RF Receiver Code Learning a New Transmitter Button: Each receiver channel can learn the codes of up to 15 different transmitters on a first-in, first-out basis. Below is the procedure for code learning a new transmitter button. 1. Press the channel mode switch of the desired channel for 3 seconds or more. The channel’s LED will start to flash quickly to indicate that it is in learning mode. 2. While the LED is flashing, press the button of the transmitter to be learned one time.
PAGE 3
ENFORCER Two-Channel RF Receiver Overview: Channel 1 mode switch Channel 2 mode switch (SK-910RB2Q only) LP3 antenna program loop 3-Pin antenna port CH 1 CH 2 Channel Function Switches Brown function switch is for channel 1 programming. Red function switch is for channel 2 programming. SK-910RB2Q shown. SK-910RBQ is the same, but only has one each: mode switch; function switch; indicator LED; channel relay. COM N.C. Ch 2 relay (SK-910RB2Q only) N.O. COM N.C. Ch 1 relay Ch 1 indicator LED N.O.
PAGE 4
ENFORCER Two-Channel RF Receiver Sample Applications: Negative Output Positive Output Positive Power Source COM NC NO — + Negative Power Output — + Power for SK-910RBQ/SK-910RB2Q Typical N.C. Application Power for SK-910RBQ/SK-910RB2Q Typical N.O. Application COM NC NO E-941SA-1200 Electromagnetic Lock — + SD-996C-NUQ Electric Door Strike COM NC NO — + N.C.