QLT25 INSTRUCTION MANUAL We’ll Make It Stress-Free If you have any questions along the way, just give us a call. 1-800-359-5520.
CAUTION: IMPORTANT SAFETY INSTRUCTIONS — PLEASE READ ENTIRE MANUAL PRIOR TO USE — SAVE THESE INSTRUCTIONS Before getting started, let’s make sure this mount is perfect for you! weigh MORE than 110 lbs. (49.8 kg)? 110 lbs. (49.8 kg) Yes? This mount is NOT compatible. Visit secura-av.com or call 1-800-359-5520 (UK: 0800 056 2853) to find a compatible mount.
Dimensions 3-D TV INTERFACE 7.87in [200mm] .59in [15mm] 1.81in [46mm] 15.98in [406mm] 23.62in [600mm] WALL PLATE 24.17in [614mm] TOP VIEW - EXTENDED 8.03in [204mm] 8° 10° 6.22in [158mm] 3.60in [91.3mm] 16.06in [408mm] 25.59in [650mm] FULLY ASSEMBLED MOUNT 25.59in [650mm] 16.93in [430mm] 5° 5.07in [129mm] 8.74in [222mm] .35in [9mm] SIDE VIEW - EXTENDED TOP VIEW - RETRACTED SIDE VIEW - RETRACTED 1.
Parts and Hardware WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! NOTE: Not all hardware included will be used.
Parts and Hardware for STEP 2 Lag Bolts 5/16 x 2¾ in. Wall Plate 10 x4 Lag Bolt Washers .695 x .350 x.075 in.
STEP 1 Attach Brackets to TV 1.1 Select Angle of TV Tilt Using the preattached angle brackets, TV can be set to either a 10° or 8° tilt. 10° Tilt 8° Tilt IMPORTANT: After attaching the brackets, adjust the straps so they are level with the bottom of the TV.
5° Tilt For 5° tilt, remove the preattached angle brackets, rotate the brackets as shown and reattach the brackets. For no tilt, remove the preattached angle brackets.
1.2 Select TV Screw Diameter 1.3 Select TV Screw Length Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter (M6, or M8) to use. If your TV has a flat back AND you want your TV closer to the wall, use the shorter screws (a).
1.4 Attach TV Brackets Ensure that your brackets are level and centered on the back of the TV. Install using the TV screw/washer/spacer configuration you selected for your TV. CAUTION: Avoid potential personal injuries and property damage! DO NOT use power tools for this step. Tighten the screws only enough to secure the TV bracket to the TV. DO NOT overtighten the screws. IMPORTANT: Ensure TV bracket is securely fastened before moving on to the next step.
STEP 2A Attach Wall Plate to Wall Wood Stud Option CAUTION: Avoid potential personal injury or property damage! Drywall covering the wall, must not exceed 5/8 in. (16 mm) Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm) Minimum horizontal space between fasteners: 16 in. (406 mm) Stud center must be verified ƕ ƕ ƕ ƕ 1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge to edge stud finder. 2.
3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit. IMPORTANT: Pilot holes must be drilled to a depth of 2¾ in. (70 mm). Be sure to drill into the center of the studs. Install wall plate 09 using four lag bolts 10 and four washers 11 . Tighten the lag bolts only until they are pulled firmly against the wall plate. 4. CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts. Go to STEP 3 on PAGE 14. 3 2¾ in. (70 mm) 4 09 7/32 in. (5.
STEP 2A Attach Wall Plate to Wall Solid Concrete or Concrete Block Option CAUTION: Avoid potential personal injury or property damage! Mount the wall plate assembly 09 directly onto the concrete surface. Minimum solid concrete thickness: 8 in. (203 mm) Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm) Minimum horizontal space between fasteners: 16 in. (406 mm) ƕ ƕ ƕ ƕ 1. Position the wall plate 09 on the wall at your desired height. Level the wall plate and mark the hole locations. 2.
3. Insert four anchors 12 . CAUTION: Be sure the anchors are seated flush with the concrete surface. 4. Install wall plate 09 using four lag bolts 10 and washers 11 . Tighten the lag bolts only until they are pulled firmly against the wall plate. CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
STEP 3 Attach TV to Wall Plate Hang TV/bracket assembly onto wall plate 09 using predetermined angle (Step 1.1 pages 6-7). Pull down on straps to lock the assembly to the wall plate 09 . 09 HEAVY! You may need assistance with this step.
Adjustments HEAVY! You may need assistance with this step. To remove the TV from the wall plate, pull down on the release straps, and then lift the TV up and out away from the wall.
Thank you for choosing Secura! Please take a moment to let us know how we did: Email us: info@secura-av.com Call us: 1-800-359-5520 UK: 0800 056 2853 Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations.
Milestone AV Technologies Australia Pty Ltd ACN 163 436 039 6/96 Gardens Drive, Willawong QLD 4110, Australia 07 32761355 Addendum -Australian Consumer Law -Warranty against defects Milestone AV Technologies Australia Pty Ltd warrants its Milestone/Secura products to be free of defects in material and workmanship for the product's Warranty Period . The Warranty Period commences on the original purchase date of the product.
