User's Manual

ManualsBrandsSecure Wireless ManualsElectronicsDEVICE CONTROLLER

Product Description

The AT&T model number SW-ATT-SRN is a proprietary

915MHz wireless siren that is capable of annunciating alarms

and keypad chirps. The DLC sends messages to the SW-ATT-

SRN via a proprietary 915MHz radio protocol to command the

SW-ATT-SRN to generate tones and pre-programmed alarm

sequences through its annunciator, including a temporal

3 - alarm (three short beeps then silence repeating) when a

smoke alarm is activated and a temporal 4 alarm (four short

beeps then silence repeating) when the CO alarm is activated.

In addition the siren beeps during an intrusion alarm.

Installing/Replacing Batteries

The siren has two (2) non-rechargeable 3V CR123A batteries

that provide twenty-four (24) hour battery backup. The batteries

can be replaced by opening the battery compartment located

on the rear of the unit.

Installing the Siren

Follow these steps to install the Siren:

1. Turn the Siren to its underside and remove the Phillips

Head screw at the bottom to open battery compartment

cover.

2. Remove the battery compartment cover.

3. Insert two (2) non-rechargeable CR123A batteries.

4. NOTE: Ensure that polarity of the batteries is correct

during installation

5. Replace the battery compartment cover and the Phillips

head screw.

6. Plug the unit into the lower socket of an AC outlet and

install a retaining screw into the plastic tab located at the

top of the unit to secure the unit to the AC outlet.

The LED shows the system status, as follows:

Solid Green

—unit is AC powered and backup battery is good.

Blinking Green

—unit is not AC powered and is operating on

backup batteries.

Solid Red

—unit is AC powered and the backup battery needs

to be replaced.

Off

—unit is not AC powered and backup battery has failed.

Discovering and Registering the Siren

Follow these steps to discover and register the siren:

1. Place the DLC into Discovery Mode in DLD.

2. Plug in the siren and once it has powered make it discoverable by

pressing the small white learn button located on the side of the

unit.

3. Conﬁ rm that the siren has been discovered in DLD.

4. Label the siren in DLD.

This equipment has been tested and found to comply with

the limits for Class B Digital Device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and

receiver

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician

for help.

Any changes or modiﬁ cations not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment.

Le présent appareil est conforme aux CNR d’Industrie

Canada applicables aux appareils radio exempts de

licence. Ľexploitation est autorisée aux deux conditions

suivantes: (1) ľappareil ne doit pas produire de brouillage,

et (2) ľutilisateur de ľappareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible

ďen compromettre le fonctionnement.

FCC Compliance Statement

This device complies with FCC Rules and

Regulations as Part 15 devices as well as

Industry Canada license exempt RSS Rules

and Regulations. Operation is subject to the

following two (2) conditions: This device may

not cause harmful interference. This device

must accept any interference received,

including interference that may cause

undesired operation.

WARNING!

The polarity of the battery must be observed. Improper handling

of lithium batteries may result in heat generation, explosion or ﬁ re

which may lead to personal injuries. Replace only with the same

as recommended by the manufacturer. Use of another battery may

present a risk of ﬁ re

or corrosion.

CAUTION!

Batteries should not be recharged, disassembled, in heat

above 100° C (212°F) or disposed of in ﬁ re.

Disposal of used batteries must be made in accordance with the

waste recovery and recycling regulations in your area.

Notice to users in California—This Perchlorate warning applies

only to Manganese Dioxide Lithium cells sold or

distributed only in California, USA. Percolate Material Special

handling may apply.

See www.dtsc.ca.gov.hazardouswaste/perchlorate.

LISTED

SW-ATT-SRN RTL 41806 Installation Instructions