User's Manual

MotionControl USER MANUAL

WIRELESS MOTION SENSOR

Quick, easy installation with no wires required. Once motion is detected a signal is sent to an

ABT ZoneControl receiver. The signal turns on any landscape lights connected to the

ZoneControl Unit. Any lights not already “On” will turn on for 5 minutes.

INSTALLATION OVERVIEW

1. Take the PIR over to the ZoneControl you want it learned into.

2. Learn the PIR into the ZoneControl

3. Test the unit to make sure it operates correctly at the desired location.

4. Mount the MotionControl unit in the desired location. ( Height of 7.5’ is recommended)

5. Adjust the angle if necessary.(left/right, up/down)

6. If desired, change the duration on the MotionControl from 5 – 60 minutes with the Programmer.

LEARNING THE MOTIONCONTROL TO A ZONECONTROL

1. With the MotionControl in hand, move to the desired ZoneControl Receiver. Place the supplied

magnet over the arrow on the left side of the MotionControl for 10 SECONDS.

2. Remove the magnet when you see a quick red flash of light on the front screen.

3. Using a magnet, swipe the ZoneControl Reed #1 (top Reed). The ZoneControl will start to click until it receives a

signal from the MotionControl. Once the signal is received the ZoneControl will stop clicking.

4. The MotionControl has a 1 minute delay before it senses movement. After 1 minute, wave your hand in

front of the MotionControl and test to make sure it senses your movement.

5. Once complete, mount the MotionControl in the desired location and see if the lights connected to the ZoneControl

turn on correctly.

WALK TEST

1. Place the supplied magnet over the arrow on the left side of the MotionControl for 2 SECONDS and then

remove it.

2. Move in the area you want covered by the MotionControl. As you walk the LED on the MotionControl

will flash. This will continue for 1 MINUTE to allow you to check the coverage of the motion sensing

beam. Note: There is a 3 SECOND delay between flashes.

DAY/NIGHT MODE

The MotionControl has a Day/Night feature built in. The MotionControl comes programmed to only trigger at night. Between 8:00 a.m. and

3:00 p.m. the MotionControl will not turn lights on. This feature can be changed with the programmer if a customer wants to have the

MotionControl trigger during the day and night.

TESTING NOTE

You can test the product 3 times before it reverts to night mode only. This is important to note that after you test 3 times the MotionControl

will revert to night time only mode. If you want to retest the MotionControl just repeat the Learning steps above.

Magnet

Reed #1

PAGE 1
MotionControl USER MANUAL WIRELESS MOTION SENSOR Quick, easy installation with no wires required. Once motion is detected a signal is sent to an ABT ZoneControl receiver. The signal turns on any landscape lights connected to the ZoneControl Unit. Any lights not already “On” will turn on for 5 minutes. INSTALLATION OVERVIEW 1. 2. 3. 4. 5. 6. Take the PIR over to the ZoneControl you want it learned into.
PAGE 2
SENSOR COVERAGE PATTERNS The Charts demonstrate how the beam pattern changes as you tilt the angle of the MotionControl. All units are in feet. 0° is the MotionControl facing straight outwards with no tilt(fig1). -9° is the MotionControl tilted down one click(fig 4). -18° is the MotionControl tilted down 2 clicks(fig 2). +9° is the MotionControl tilted up one click(fig 3). Distance Ft. Distance Ft.
PAGE 3
MOUNTING 1. Optimal mounting height is 7.5 Ft. Attach the MotionControl to the [A] mounting arm with a screw. Screw the [B] mounting bracket into the wall using the 2 wall mount screws. Place the MotionControl on the mounting bracket and screw in the top screw. To tilt the MotionControl simple loosen the screw, adjust the unit ( 1 or 2 clicks) and re-tighten. FAQ’s and HINTS Question Answer My MotionControl unit does not turn the lights on.