Operating instructions

ManualsBrandsSecureHome ManualsCamera AccessoriesSH-9525AU

REQUIREMENTS

•elightcontrolrequires230voltsAC.

•IfyouwanttouseManualMode,thecontrol

mustbewiredthroughaswitch.

•It is illegal for persons other than a licensed

electrician or person authorized by legislation

to work on xed wiring or other electrical

installations.

Before installation, record the model num-

ber listed inside the xture. Attach receipt

in case of possible warranty issues.

Model Number:

Security Light*

*Note:Illustrationsareforreferenceonlyandmay

bedierentfromactualproduct

Motion Sensing

Halogen Fixture

FEATURES

•Automatically comesonwhen motion isde-

tected.

•Automaticallyturnslighto.

•Photocell keeps the light o during daylight

hours.

•LED indicates motion was sensed (day or

night).

UNPACKING

Besuretoremoveallcontentsfrompackaging

andverifyallitemsarepresentbeforeassembling

thislightxture.ispackageincludesthefol-

lowingitems:

•SecurityLight

•CanopyExtensionwithRubberGasket

•RubberPlug

•MountingBolt

•LightShield

•Owner’sManual

Installation and Operating Instructions

Model: SH-9525AU

Summary of content (12 pages)

PAGE 1
® TM Motion Sensing Halogen Fixture Model: SH-9525AU Installation and Operating Instructions FEATURES • Automatically comes on when motion is detected. • Automatically turns light off. • Photocell keeps the light off during daylight hours. • LED indicates motion was sensed (day or night). REQUIREMENTS • The light control requires 230 volts AC. • If you want to use Manual Mode, the control must be wired through a switch.
PAGE 2
IMPORTANT SAFETY AND INSTALLATION INFORMATION Before installing security light, read all instructions carefully and keep owner’s manual for future reference. • WARNING: To prevent electric shock, please ensure that power is disconnected before installation. • WARNING: Risk of fire. Keep fixture at least 51 mm (2") from combustible materials. Do not aim at objects closer than 1 meter (3 feet). 1m • CAUTION: Allow fixture to cool before touching. The bulb and the fixture operate at high temperatures.
PAGE 3
INSTALLATION Canopy Extension This light fixture must be installed by a licensed electrician or other person authorized by legislation to work on fixed wiring or other electrical installations. UP WARNING: Turn power off at circuit breaker or fuse. Place tape over circuit breaker switch and verify power is off at the fixture. IMPORTANT: Do NOT use with dimmers or timers. For best performance, mount the fixture about 2.4 meters (8 feet) above the ground. Note: If fixture is mounted higher than 2.
PAGE 4
WIRING FINAL ASSEMBLY 1. Double check all wiring connections. 2. Verify the rubber gasket is properly seated around the edge of the canopy extension (see Figure 6). 3. Align the center hole on the fixture canopy with the center hole on the canopy extension and attach using the mounting bolt removed in step 1 of Installation (see Figure 6). IMPORTANT: • If wall mounted, make sure the fixture is mounted with the sensor below the bulb holders.
PAGE 5
BULB INSTALLATION AND REPLACEMENT Caulk Upper Half of Canopy Extension CAUTION: When replacing bulb, turn power off and let the fixture cool. Canopy Extension UP Rubber Plug Important: Use a clean glove or cloth when handling the new bulb. Use isopropyl (rubbing) alcohol to clean the bulb if it is touched with your bare hands. Figure 7 EAVE INSTALLATION INFORMATION NOTE: The bulb is included, but need to be installed. The bulb is located behind the glass cover of the lamp head. 1.
PAGE 6
TESTING AND ADJUSTMENTS 4. Loosen the clamp screw in the sensor Clamp ball joint and gently Screw rotate the sensor. Ball 5. Walk through the Joint coverage area noting where you are when the lights turn on (also, the LED will flash several times when Aim Sensor Down motion is detected). In for Short Coverage TEST mode, light will stay on for 5 seconds after motion has stopped and then turn off. Move the sensor head Aim Sensor Higher up, down, or sideways for Long Coverage to change the coverage area.
PAGE 7
OPERATION Mode: Test Auto Manual On-Time 5 Seconds 1, 5, or 10 Minutes To Dawn* LIGHT SHIELD INSTALLATION If your light does not come on at dusk or turns off unexpectedly, then another light source may be activating the daytime shutoff feature. Possible sources of light interference are street lights, landscape lighting, other security lights or lanterns, or an interior house light shining through a window. It could also be reflective light, such as from a pool or light colored wall.
PAGE 8
SPECIFICATIONS Range ��Up to 21 m (70 ft.
PAGE 9
CHAMBERLAIN LIMITED WARRANTY Lighting and Chime Products Chamberlain Australia Pty Limited / Chamberlain New Zealand Limited (Chamberlain) is committed to manufacturing and supplying high quality goods. As part of this commitment, we seek to provide reliable service and support for our goods and are pleased to provide you, the original purchaser, with this Chamberlain Limited Warranty.
PAGE 10
NOTES__________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ 10 201114-01
PAGE 11
NOTES__________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ 201114-01 11
PAGE 12
NOTES__________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ 12 201114-01