User Manual

Rotate to
Adjust
1-3/4” Door: 7/16”
2” Door: 9/16”
2-1/4” Door: 11/16”
4. Unpack Lock.
A. Remove the lock components from
the box.
edge of door. 40 5/16” (1024mm)
Note:
To avoid splintering wood
doors, drill holes (A) and (C)
from both sides of the door.
D
C
R
For Schlage Removable Core
match driver position in handle to
the sketch below for proper
alignment.
Correct position
of Schlage Connecting Bar
when assembled:
Notches toward free end of handle
*2 1/8” (54mm) hole saw
*1” (26mm) boring bit
*5/16” (8mm) drill bit
*7/64” (2.5mm) drill bit
Through Bolts
In U.S.A.
Yale Security Inc.
1902 Airport Road
Monroe, NC 28110
[phone]
[phone]
[phone] (Fax)
In Canada
Yale Security Inc.
6940 Edwards Blvd
Mississauga, Ontario
Canada L5T2W2
[phone]
[phone]
[phone] (Fax)
E
Outside Assembly
(stays assembled)
Tools Required
8. Strike Installation (Wood Frames Only)
A. Close door and mark a horizontal line
from the center of the template to the
frame of the door.
B. Measure half the thickness of the door;
mark this same distance with a vertical
line starting from the stop side of the
frame and where both lines cross make
a 1 inch (26mm) diameter hole and
½ inch (13mm) in depth.
C. Align the holes of the strike with the
vertical line, trace the outline of the strike
and mortise to 1/16 inch (1.6mm) depth.
Attach the strike with two screws (provided).
TEST THE OPERATION OF THE LOCKSET
Cycle the lock in both the locked and unlocked
positions. If lock functions smoothly when door
is open, but binds when closed, check door and
frame alignment. If problems are found see
troubleshooting below.
Troubleshooting
1. Check door
2. Check hinges. They should not be loose or have excessive
wear on knuckles.
3. Latchbolt will not deadlock.
Either strike is out of line or gap between door and jamb is
too great. Realign strike or shim strike out towards flat area
of latchbolt.
4. Latchbolt does not retract or extend properly.
Latchbolt tail and retractor not properly positioned.
A. Remove lockset. Look through 2 1/8 hole and verify
latchbolt tail centered between top and bottom of hole.
B. Remove latchbolt and insert lockset, look through
latch hole and verify retractor mouth centered in
hole. Adjust outside rose plate if not.(See #5 on page 2)
C. Rebore holes if necessary to line up retractor and tail.
Door Must Not Bind Door Must Not Be Warped
Door Must Not Sag
Door Must Swing Freely
A. Drill 2 1/8” (54mm) dia. hole thru
the door. Cut notches as shown
on template. See note.
(Except Dummy Trim)
B. Drill 1” (25mm) dia. hole in
edge of door. Mortise for latch
front 1 1/8” (29mm) wide
X 2 1/4” (57mm) high X 5/32”
(4mm) deep. (Except Dummy Trim)
C. Drill two (2) 5/16” (8mm) dia.
Holes thru door. See note.
D. Drill pilot holes for latch screws.
7/64” (2.5mm) dia. (Except
Dummy Trim)
* Chisel & hammer
* #2 phillips screw driver
* Handle removal tool (supplied)
* 3/8” or I/2” drill
Yale is a registered trademark of Yale Security Inc.
Other product brand names may be trademarks or
registered trademarks of their respective owners
and are mentioned for reference purposes only.
These materials are protected under US copyright
laws. All contents current at time of publication.
Yale Security Inc. reserves the right to change
availability of any item in this manual, it’s design,
construction, and/or it’s material.
Copyright 1998, 2004 Yale Security Inc.
All rights reserved.