User guide

ManualsBrandsSecuritron ManualsPower suppliersAQD3

Installation Guide AQD3 12/24 Series Power Supplies

Securitron Magnalock Corporation

10027 S. 51

St., Ste. 102

Phoenix, AZ 85044

Doc.# 500-33000 Rev A Installation specifications subject to change without notice

ASSA ABLOY, the global leader

in door opening solutions.

Phone: (800) MAGLOCK

customercare@securitron.com

www.Securitron.com

Page 1 of 15

AQD3 Series 12/24 Power Supply

9.8Vdc-13.7Vdc @ 2.8 Amps max / 20.0Vdc-27.5Vdc @ 1.4 Amps max

Power-limited

Features AQD3 Series:

 Small – Self Contained – Efficient

 Universal AC Input 110-240vac

 Extraordinary Brown Out Capability

 9.8Vdc-13.7Vdc, 2.8A/20.0Vdc-27.5Vdc, 1.4A

Selectable Continuous Duty

 Very Clean Output - 10mv ripple rms

 Input and Output Surge Protection

 Power Limited Output with Thermal Protection

 AC and DC LED’s

 Quality Manufactured in the USA with a lifetime

Warranty

 Outputs are Power Limited

 Provided in Standard Enclosure 14”x8.5”x3.5”

 Precise Battery Regulation for all sealed Lead

Acid Battery(s)

 Battery Online, No Drop or Switch Over with AC

Power Fail

 Reverse Battery Protection

 Comes with plug in battery cable assembly

 UL and cUL tested to Standards UL 603 Burglar

Alarm Power Supplies, UL 294 Access Control

Units, and ULC-S318-96 Canadian Standard for

Power Supplies for Burglar Alarm Systems

 Relay “C” Contacts Indicates AC Power Status

 LTW Limited Warning of stand by battery(s)

 Battery Disconnect on depleted Battery(s)

Ordering examples:

AQD3

Supervised Power Supply/Charger module

with Standard Enclosure 14”x8.5” x 3.5”

-8F8R

-4C

-8C

-4F

-8F

-1R

-8C1R

AQD3 with one

PDB-8F8R

AQD3 with one PDB-4C

AQD3 with one PDB-8C

AQD3 with one PDB-4F

AQD3 with one PDB-8F

AQD3 with one PDB-FT

AQD3 with one PDB-8C1R

Summary of content (15 pages)

PAGE 1
Installation Guide AQD3 12/24 Series Power Supplies AQD3 Series 12/24 Power Supply 9.8Vdc-13.7Vdc @ 2.8 Amps max / 20.0Vdc-27.5Vdc @ 1.4 Amps max Power-limited Features AQD3 Series:  Small – Self Contained – Efficient  Universal AC Input 110-240vac  Extraordinary Brown Out Capability  9.8Vdc-13.7Vdc, 2.8A/20.0Vdc-27.5Vdc, 1.
PAGE 2
AQD3 Series Installation continued Description The AQD3 Series Power Supplies are heavy duty self contained, efficient clean off-line switching power supplies that are selectable between 9.8Vdc-13.7Vdc at 2.8 Amps, and 20.0Vdc-27.5Vdc at 1.4 Amps. With the universal AC input, these supplies may be connected anywhere in the world with no plug-in transformer or any alterations. These power supplies have exceptional brown out capability with operation down to 60vac.
PAGE 3
AQD3 Series Installation continued AQD3 Supervised added features: DC Output Electronic Power Limited ...................... Yes This feature limits the output current to a maximum peak of 6Amps to comply with UL Power Limiting requirement. AC Status Output Relay: 3P Terminal block AC Fail form “C” contacts rating .................... 2A, 24Vdc Three position AC fail terminal block marked “NO, C, NC” are shown in the Normal, energized, “AC ON” condition.
PAGE 4
AQD3 Series Installation continued AQD3 , Power Supply/Charger Installation Guide The AQD3 with standby battery(s) provide an uninterruptible 9.8Vdc-13.7Vdc or 20.0Vdc-27.5Vdc power source. The Power Distribution modules provide multiple fused outputs, Fire Interface, and Access control Interface. The DC output on the AQD3 power supply is Power Limited. This makes all subsequent outputs power limited. 1.
PAGE 5
AQD3 Series Installation continued Battery Selection The table below shows typical standby time in hours for various loads and batteries. The table works for either 12v or 24v batteries. The AQD3 has been evaluated by UL with an 18AH sealed lead acid battery for 12v and (2) - 9AH batteries for 24v to meet the 4 hour stand by requirement. Note: UL requires a minimum of 4 hours of standby time for Commercial Mercantile Burglar Alarm.
PAGE 6
AQD3 Series Installation continued AQD3 Series Instructions: Doc.
PAGE 7
AQD3 Series Installation continued AQD3 Series Instructions: Doc.
PAGE 8
AQD3 Series Installation continued AQD3 Series Instructions: Doc.
PAGE 9
AQD3 Series Installation continued AQD3 Series Instructions: Doc.
PAGE 10
AQD3 Series Installation continued PDB-4F / PDB-8F Multi Output Low Voltage Power Distribution Modules Life Time Warranty Features/Specifications:  Converts a single AC or DC (12 or 24v) Input to 4 or 8 protected outputs with fuses or circuit breakers  1500 Watt surge protection on PDB-8F Input rated 22 Amps @ 32 volts AC or DC  All PTC circuit breaker ratings are holding current at 130oF per UL Standards  Main Power Green/Red LED Indicates AC, DC or Reversed DC Input on PDB-8 and PDB-9  Each output ha
PAGE 11
AQD3 Series Installation continued PDB-FT Fire Transfer Relay with EOL Trigger Features:  Non Latching or Latching mode  12 or 24VDC Operation  Reverse polarity protected  Normally ON & Normally OFF Output  Output LED’s indicate condition  Outputs can be Triggered with: 1. N/O or N/C Switch with Supervised (EOL) 2. N/C Switch with (OVR) over ride 3. N/C Switch with AUX-IN auxiliary 4.
PAGE 12
PDB-8F8RAccess Control with EOL Fire Interface Installation Instructions PDB-8C1R DC Power Distribution with Supervised Interface module Distributed Power Control Interface for Fire, Access, HVAC, Elevator, and Security             Features: 8 Power Limited Outputs with Auto-Resetting Circuit Breakers Each Output is Individually Selectable to Turn On, Turn Off, or always ON when Triggered Outputs can be triggered with: 1. Voltage or Reverse polarity (opto isolated) 2.
PAGE 13
AD3 Series Installation Instructions PDB-8F8R Power Distribution for Access Control with Fire Interface module Controls and Distributes Power with 8 Control Relays with an EOL Fire trigger Interface Power Interface for Access Control, CCTV, Fire, HVAC, Elevator, and general low voltage system control S Note: Fire, HVAC and Elevator Control has not been evaluated by UL  Features:  8 Heavy duty Relays with individual Inputs and Status LED’s  Each Relay Input can be Activated from Low Current Open Collect
PAGE 14
AQD3 Series Installation Instructions products. J1 Connects (-) Power to (-) Control, J2 Connects (+) Power to (+) Control. By default J1 & J2 are connected together. When J1 & J2 are cut, you must supply 11 to 27.5Vdc to Control power, then you may connect any voltage to 32V AC or DC to the Main Power Terminals. See Dual/Separate Power application figure below. Inputs (1-8 IN C) Eight, two position un-pluggable terminal blocks. When IN & C are shorted together, the like number output relay will energize.
PAGE 15
AQD3 Series Installation Instructions PDB-8F8R Typical Applications Single Power Source Application Fig 1 Dual/Se parate Power Supplies Fig 3 AQD3 Series Instructions Doc# 500-33000 Rev.