Manual

ManualsBrandsSecuritron ManualsFor HomeEMB_Series

Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader

Tel 800.624.5625 techsupport@securitron.com

in door opening solutions

Page 1 Rev. C, 03/11

ELECTRO-MECHANICAL BAR (EMB) SERIES

INSTALLATION INSTRUCTIONS

1. SPECIFICATIONS

MECHANICAL ELECTRICAL/ENVIRONMENTAL

Physical Size:

Height: 2-5/8” [66mm]

Depth: 1-5/8” [41mm] (from mounting

surface)

Overall Length:

36” Door = 34-1/2” [876mm]

42” Door = 40-1/2” [1029mm]

48” Door = 46-1/2” [1181mm]

Operating Force (Maximum): 15 Lbs. [66.7N]

Maximum Recommended Current:

1.5 Amps @ 30VDC

Environmental (Recommended):

Temperature: 32ºF to 120ºF [0ºC to 49ºC]

Humidity: 10% to 90% RH

2. COMPONENTS

EMB UNIT PACKAGE

MOUNTING HARDWARE

4X – 1/4-20 Blind Nut 4X – External Tooth Washer 2X – End Mount Retainer

4X – 1/4-20 x 1” Long

Phillips Pan Head

1X – Blind Nut Installation Tool 2X – E-clip

SB-C

Mounting

Hardware

EMB

Push To Exit

Label

Summary of content (8 pages)

PAGE 1
Securitron Magnalock Corp. Tel 800.624.5625 www.securitron.com techsupport@securitron.com ASSA ABLOY, the global leader in door opening solutions ELECTRO-MECHANICAL BAR (EMB) SERIES INSTALLATION INSTRUCTIONS 1. SPECIFICATIONS MECHANICAL ELECTRICAL/ENVIRONMENTAL Physical Size: Maximum Recommended Current: Height: 2-5/8” [66mm] Depth: 1-5/8” [41mm] (from mounting surface) Overall Length: 36” Door = 34-1/2” [876mm] 42” Door = 40-1/2” [1029mm] 48” Door = 46-1/2” [1181mm] 1.
PAGE 2
3. DOOR PREPARATION New Installation:  With the door in the closed position, verify that the bar fits between the stops of the door frame. If not, the bar may be shortened as described in Section 6.  Review the following illustrations and determine the mounting configuration to be used (i.e. hollow metal, solid wood or through door).  Using a Phillips screwdriver, remove the bar end caps.  Position and level bar against inside of door between frame stops.
PAGE 3
Hinge Side of Door Mounting Diagram Hollow Metal (Aluminum Frame Glass) Door Preparation Shown * NOTE: Drill holes through mounting side of hollow doors only! Blind Nut Installation:  Insert the blind nut of the installation tool into a 3/8” [9.5mm] diameter hole.  Hold the collapsing nut with a 1/2” box end wrench.  While maintaining pressure toward the mounting surface, use a 3/16” hex wrench to tighten the cap screw and collapse the blind nut.
PAGE 4
. INSTALLATION Mount Bar to Door:  Feed wire cable through hole in door, or route wire through the end cap (See Wire Routing instructions in Section 5).  Install bar to door (Detail C) using included hardware – or the hardware from previous bar installation.  Ensure that the end mount retainer is used to provide secure attachment to door.  Connect electrical circuit(s) and test operation (See Section 7 for general wiring diagrams).  Install bar end caps and the push to exit label. 5.
PAGE 5
.1 WIRE ROUTING THROUGH END CAP (OPTIONAL) Drill End Cap: OR Left End Cap (Bottom) Right End Cap (Bottom)  Determine which bar end cap to feed the flexible door cord shield into. Normally the bar wire cable and door cord shield go to the hinge side of door.  Mark and/or center punch the bottom side of the chosen end cap at the location shown.  Drill a 3/8” [9.5mm] diameter hole through the wall of the end cap.
PAGE 6
. SHORTENING THE BAR (OPTIONAL) Measure for fit:  Measure the distance between stops on the door frame.  Subtract 2” [51mm] from the distance measured between stops. This will be the measurement to use to cut both of the aluminum bar extrusions. o Example: The distance between stops is 31-3/4 inches [806mm], subtract 2 inches [51mm] = total extrusion length of 29-3/4 inches [755mm].
PAGE 7
. ELECTRICAL CONNECTION Typical Wiring Configurations: The following wiring diagrams are provided as examples of various egress control configurations. Single Magnetic Lock: Note: Each wiring diagram shows an MOV wired in parallel with the suppress the inductive kickback generated by a lock which, if shorten the life of the bar’s switch contacts. The MOV has no properly it should be spliced into the wiring as close to the lock with each EMB unit. magnetic lock.
PAGE 8
Double Break Wiring Many installations include a controlled access device such as a digital keypad or card reader. Such devices typically have a REX (request to exit) input. When dry contacts close on this input, the entry device will open the lock for the same amount of time that is programmed for entry. Implementation of the REX input for exit can provide timed exiting. Also, for most entry controls, the REX input must be used for exiting to avoid an alarm condition at the door.