Programming instructions

Digital Monitoring Products XR200-485 Programming Guide
18
SYSTEM REPORTS
XR200-485 Programming Guide Digital Monitoring Products
19
SYSTEM OPTIONS
System Options
7.1
SYSTEM OPTIONS
System Options
This section allows you to select system-wide parameters.
7.2
CLS WAIT NO YES
Closing Wait
When YES, the keypad displays ONE MOMENT... while the system waits for an
acknowledge from the receiver before arming the selected area(s) and performing
a Bell Test (if selected). Exit delays begin after the Closing Wait. Opening/Closing
reports must be YES to enable Closing Wait.
7.3
ENTRY DELAY 2: 60
ENTRY DELAY 3: 90
ENTRY DELAY 1: 30
ENTRY DELAY 4: 120
Entry Delay 1
Enter the Entry Delay time for all Exit type zones programmed to use Entry Delay 1.
When an armed Exit type zone is faulted, the keypad prewarn tone begins sounding
and ENTER CODE:- displays on all keypads programmed to prewarn for that zone.
The area must be disarmed before the delay expires or an alarm report is sent to the
receiver. All zones in that area are delayed along with the Exit zone. Entry Delay
times can be from 1 to 250 seconds. Repeat the above for each entry delay being
used in the system.
7.4
CRS ZONE TM: 4
Cross Zone Time
Enter the time allowed between zone faults. When zones are cross zoned, a second
cross-zoned zone in the same partition must fault within this time in order for an
alarm report from the rst zone to be sent to the receiver. If the cross-zone time
expires without the second zone faulting, only a zone fault from the rst zone is
reported. Cross-zone time can be from 4 to 250 seconds. Entering zero disables this
function. See the Appendix.
7.5
RETARD DELAY: 10
Zone Retard Delay
Enter the retard time assigned to Fire, Supervisory, Auxiliary 1, Auxiliary 2, and
Arming type zones. The retard delay only functions when the zone shorts. The
zone must remain shorted for the entire length of the Retard Delay before being
recognized by the panel. The Zone Retard Delay can be from 1 to 250 seconds.
Entering a zero disables this function.
If the zone is programmed as an Auxiliary 2 or Arming type, the Zone Retard Delay
timer is counted in minutes. This allows a light sensor, which detects darkness and
obstructing objects, to be connected to the zone.
Note: The number entered for Zone Retard Delay is used for all types of zones
that are programmed for Retard in Zone Information. For example, if you enter a
15-second delay for Fire zones, there will be a 15-minute delay for Auxiliary 2 and
Arming type zones.
7.6
PWR FAIL HRS: 1
Power Fail Delay
This option tracks the duration of an AC power failure. When the AC power is off for
the length of the programmed delay time, an AC power failure report is sent to the
receiver. The delay time can be from 1 to 9 hours. Entering a zero sends the power
failure report after a 15-second delay. The default setting is 1.
7.7
SWGRBYPS TRIPS: 3
Swinger Bypass Trips
Enter the number of times a zone can go into an alarm or trouble condition within
one hour before being automatically bypassed. You can select from 1 to 7 trips.
Bypassed zones automatically reset when the area they are assigned to is disarmed.
All 24-hour zones reset when any area of the system is disarmed. Entering a zero
disables this function.
How it works
The panel hour timer starts at 59 minutes past the hour. If the hour timer expires
before the trip counter is exceeded, the trip counter returns to zero. If the trip
counter is exceeded before the hour expires, the zone is automatically bypassed by
the panel. A Bypass Report is sent to the receiver if Bypass Reports is YES.