User’s Guide MOBILE APP BASED Wireless Security Alarm System R EG IS A TE R PO RM W ER Model: IWATCHALARMD SOS
© Copyright 2016 This manual is furnished under license and may be used or copied only in accordance with the terms of such license. Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or any means, electronic, mechanical, recording, or otherwise, including translation to another language or format, without the prior written permission of SecurityMan.
The liability of SecurityMan Inc, arising from this warranty and sale shall be limited to a refund of the purchase price. In no event shall SecurityMan be liable for costs of procurement of substitute products or services, or for any lost profits, or for any consequential, incidental, direct or indirect damages, however caused and on any theory of liability, arising from this warranty and sale. These limitations shall apply not withstanding any failure of essential purpose of any limited remedy.
Table of Contents Introduction Features Important Restrictions Package Contents Product Basics Alarm Host (SM-025H) Door / Window Sensor (SM-002M) Motion Sensor (SM-003P) Indoor Siren (SM-005SR) Remote Control (SM-007R) Quick Start Hardware Setup Alarm Host Door / Window Sensor Motion Sensor Indoor Siren Remote Control Smartphone Smart Config Method Adding Devices and Cameras Door / Window Sensor Motion Sensor Indoor Siren Remote Control Doorbell Mounting Instructions Home Automation Wall Socket
HomeBot Control Center Features & Options Main Screen Symbols and Notifications Back Alarm Status Sensor Status Icons and Settings Arm Silent Arm Disarm Camera (Optional SM-821DTH & SM-825DTH) Options and Settings Back Device List Area Camera Live View Settings and Options Back Snapshot Refresh Talk Record Camera Settings Camera Settings & Configurations DID Firmware Version Check Upgrade Change Password Change Admin Pass Moti
Add (Refer to Adding Devices and Enable / Disable Wall Socket (Optional Add-On) Wall Socket Options and Settings Back Device List Area Add (Refer to Adding Devices and Enable / Disable Door / Window Sensor Door / Window Sensor Options and Settings Back Device List Area Add (Refer to Adding Devices and Enable / Disable Motion Sensor Motion Sensor Options and Settings Back Device List Area Add (Refer to Adding Devices and Enable / Disable Keychain Remote
Introduction The SecurityMan IWATCHALARM is an App based wireless Security System that puts you in full control of your home or business security. The IWATCHALARM app lets you use your Smartphone or tablet to arm, disarm and monitor your security system at any time without service fees or contracts. It shows you when the system has been armed, disarmed, and lets you turn any device on/off at any given time.
• DO NOT place this product too close to medical equipment. 1. Radio waves may potentially cause breakdown of medical electrical equipment and thus cause incidents. 2. Place this product at least 22cm from the heart pacemaker. Radio wave potentially influences heart pacemaker and thus leads to respiratory disturbance. • DO NOT uses this product to monitor equipment or activities that are relevant to one’s privacy.
• DO NOT use the camera in the places which are covered with metal. The around metal, such as elevator and cabin, might shield the electromagnetic wave, and result in inability to receive signals.
Package Contents SM-025H Alarm Host SM-005SR Indoor Siren Power Adapter (2) (Host & Siren) Ethernet Cable SM-002M Door/ Window Sensor SM-003P Motion Sensor SM-007R Keychain Remote Mounting Accessories Quick Start Quide User’s Manual Wall-Mount Bracket (Alarm Host) 4 Warning Sign
Product Basics ALARM HOST (SM-025H) 1. Wi-Fi Antenna. 2. Wireless Antenna (433MHz). 3. Arm. 4. Disarm. 5. Power (press and hold to turn on/off). 6. Status LED’s. 7. AP (used as an alternative method when adding sensors). 8. Reset. 9. On/Off switch. 10. Ethernet Port. 11. Power Port. 12. Wall-Mount inserts (8). NOTE: The alarm host has an internal built-in backup battery that can last up to 6 hours.
1. 2. 3. 4. 5. Power LED (flashes on/off whenever a door or window is opened or closed). Emitting sensor (normally mounted on the door or window frame). Magnetic piece (normally mounted on the window or door). Battery compartment (make sure all plastic is removed from the battery prior to inserting it, 1x AA battery). Pair button (used to add the sensor to your alarm host).
1. 2. 3. 4. 5. Strobe LED’s (flashes whenever the alarm is tripped). Tamper switch (sets the siren off whenever it is lifted from its fixed location). Power socket and cable management slot. Pair button (used to add the siren to your alarm host). Mounting holes (for accurate positioning please use the anchor guidance card). NOTE: The indoor siren contain internal backup battery slots for 3 AA batteries in case of power outage (Batteries not included). REMOTE CONTROL (SM-007R) 1. 2. 3. 4. 5. 6.
Quick Start NOTE: All sensors included with your kit have already been paired/synced to the alarm host and ready to go. Make sure you remove any plastic wraps from the batteries provided before inserting them. After powering up the host and all wireless sensors, please test all the senors first to ensure they operate well before mounting your sensors. Please refer to each sensors syncing procedure if it does not show up on the Smartphone app.
MOTION SENSOR (SM-003P) Using a Philips screw driver, remove the screw located at the top of motion sensor, detach the front cover and Insert the 2 AAA batteries that were provided (Make sure the + and – polarities are correct). Once the batteries have been inserted the red LED should start to flash or stay solid indicating that it is now operable. Re-attach the front cover and insert the mounting bracket into the bracket slots located on the back of the sensor.
REMOTE CONTROL (SM-007R) Please pop open the top and back panels of the remote control to remove the clear plastic battery protector before use (please do this by hand only, do not use sharp utensil or screw driver). Once removed, place the top and back panels back together and test the remote by pressing any button. The red LED should flash with each press. STEP 2 SMARTPHONE SETUP Smart Config Method 1. Open the App Store (iOS) or Google Play (Android) on your mobile device.
2. Now select the Smart Config option (Fig 2.4) to begin the adding process. Turn your alarm host upside down then “Press and Hold” the pair button (Fig 2.5) until the pair LED located on the top of the host begins to flash rapidly and then press next on the Smartphone prompt. Input the Wi-Fi password of the network that you are currently connected too (Fig 2.6) and press next. This will allow the app to smart configure the camera using your current wireless network. Fig 2.4 Fig 2.5 Fig 2.6 3.
Adding Devices and Cameras By default right out the retail box, all the wireless devices are already paired to the alarm host. In situation where they are not paired, the HOMEBOT Smartphone app has a built in “user friendly” step-by-step interactive guide that you can follow when adding each device. • Make sure you have the app installed on your Smartphone or tablet and that you have successfully added the alarm host to the app.
2. On the control center, tap on the door/window sensor icon and then tap on the + (add) symbol to begin adding the new sensor. 3. “Press and Hold” the pair button on the door/widow sensor being added until the sensors LED begins to flash rapidly and then press next on the Smartphone prompt. Once your sensor has been detected by the alarm host you will be given the opportunity to name the device prior to saving it. 4.
MOTION SENSOR (SM-003P) 1. Using a Philips screw driver, remove the screw located at the top of motion sensor, detach the front cover and Insert the 2 AAA batteries that were provided. Once the batteries have been inserted the blue LED should flash indicating that it is now operable. 2. On the control center, tap on the motion sensor icon and then tap on the + (add) symbol to begin adding the new sensor.
3. “Press and Hold” the pair button on the motion sensor being added until the sensors LED begins to flash rapidly and then press next on the Smartphone prompt. Once your sensor has been detected by the alarm host you will be given the opportunity to name the device prior to saving it. 4. Once the sensor has been successfully added to the host, re-attach the front cover and insert the mounting bracket into the bracket slots located on the back of the sensor.
INDOOR SIREN (SM-005SR) 1. Insert the female end of the sirens AC adapter into the DC in port located behind the siren and the other end into a wall outlet closest to the alarm host. Make sure you place the siren face down leaving the pair button exposed. 2. On the control center, tap on the siren icon and then tap on the + (add) symbol to begin adding the new siren. 3.
4. Once the siren has been successfully added to the host you may unplug the AC adapter and mount the siren to your wall using the screws provided. Once the siren has been mounted, plug the AC adapter into a wall outlet. Please note that the siren is equipped with a tamper proof switch (located on the back) that will trigger the siren to go off whenever the siren is lifted off the wall. REMOTE CONTROL (SM-007R) 1.
3. “Press and Hold” the pair button on the remote being added until the remotes LED begins to flash rapidly and then press next on the Smartphone prompt. Once your remote has been detected by the alarm host you will be given the opportunity to name the device prior to saving it. 4. Once the remote has been successfully added to the host, you can attach it to your existing key ring using the ring provided.
DOORBELL (SM-105DB, optional add-on) 1. Remove the battery cover from the back of the doorbell by sliding it downward, insert the 2 AAA batteries that were provided and slide the cover back on. Once the cover is back on, test the doorbell by pressing the button and the red LED should flash with each press. 2. On the control center, tap on the doorbell icon and then tap on the + (add) symbol to begin adding the new doorbell. 3.
4. Once the doorbell has been successfully added to the host, you can mount it in the desired location. The back panel adhesive Velcro makes it convenient to remove at any time for portability. Mounting the DOORBELL (optional add-on) 1. Remove the backing on the slotted piece of Velcro and attach it to the back end of the doorbell as shown below. Make sure the slots align perfectly around the battery compartment so that it does not complicate changing the batteries later.
2. Find a dry location for the door bell and screw in the abrasive piece of the Velcro using the screws provided. Then attach the doorbell to the abrasive end of the Velcro that was screwed into the wall and you are done. HOME AUTOMATION WALL SOCKET (SM-001SK, optional add-on) 1. Plug the wall socket into an electric outlet closest to the alarm host and make sure it is in the “on” (power LED on) position. You can re-position it to another location once it is paired to the host. 2.
3. “Press and Hold” the pair button on the socket being added until the LED begins to flash rapidly and then press next on the Smartphone prompt. Once your wall socket has been detected by the alarm host you will be given the opportunity to name the device prior to saving it. NOTE: Please make sure the wall socket is “ON” prior to pressing and holding the pair button or the host will fail to pair it. 4.
Basic Operations The SM-001SK Home Automation Wall Socket allows you to control the ON and OFF function of any device that is connected to it, such as a Lamp, a radio, etc. To control the wall socket simply launch the control center on your Smartphone or tablet and select the Wall Socket icon. Then tap the “on / off” switch to turn your device on or off. WIFI PAN-TILT CAMERA (SM-821DTH, optional add-on) 1. Screw in the cameras antenna and insert your Micro SD memory card (not included) into the TF slot.
2. Make sure your Smartphone or tablet is connected to the same Wi-Fi network as the one you want to put the camera on and on the control center, tap on the camera icon and then tap on the + (add) symbol to begin adding the new camera. 3. Select the camera number you want to add the new camera to and then tap “yes” on the confirmation popup to proceed. NOTE: To remove a camera simply tap on any of the checked camera numbers and then confirm its removal by tapping on Yes at the prompt. 4.
5. “Press and Release” the pair button on the back of the camera. At this point the green power LED located on the front of the camera will start to flash rapidly indicating that it is in pair mode. When you see the LED flashing rapidly press next on the Smartphone prompt. Input the Wi-Fi password of the network that you are currently connected too and press next. This will allow the app to smart configure the camera using your current wireless network. 6.
WIFI FIXED CAMERA (SM-825DTH, optional add-on) 1. Insert your Micro SD memory card (not included) into the TF slot. Then insert the female end of the AC adapter into the DC in port located behind the camera and the other end into a wall outlet closest to the alarm host. You can re-position the camera to a different location once it has been successfully paired to the host. NOTE: The wifi fixed camera can be used to integrate with the IWATCHALARM system or it can be used as a standalone wifi camera. 2.
3. Select the camera number you want to add the new camera to and then tap “yes” on the confirmation popup to proceed. NOTE: To remove a camera simply tap on any of the checked camera numbers and then confirm its removal by tapping on Yes at the prompt. 4. Now select Search in LAN and select the Smart Config option to begin the adding process.
5. “Press and Release” the pair button on the back of the camera. At this point the green power LED located on the front of the camera will start to flash rapidly indicating that it is in pair mode. When you see the LED flashing rapidly press next on the Smartphone prompt. Input the Wi-Fi password of the network that you are currently connected too and press next. This will allow the app to smart configure the camera using your current wireless network.
6. Once your camera has been detected by the host the green power LED on the camera should start to flash steady. Now input the default camera password 123456 when prompted, tap save and then tap ok on the successfully registered prompt to complete the process. HomeBot Main Screen Features & Options 1. 2. 3. 4. 5.
ALARM HOST IMAGE The alarm host image is immediately displayed once you have successfully added a new host to the HomeBot app and is mainly used whenever you need to access the apps control center. To access the control center simply tap on the alarm host image as shown in the image below. NOTE: If more than one host has been added, swipe until the desired host is displayed and tap on its image.
1. Search in LAN 2. QR Scan 3. Manual Input SEARCH IN LAN The Search in LAN options are specifically designed to perform searches over your Local Area Network quickly and efficiently while being easy enough to use that it doesn’t confuse you with hundreds of options. • Smart Config • Broadcast in LAN • AP Mode SMART CONFIG To add your alarm host to the HomeBot app using the Smart Config method, make sure your new alarm host in powered on and follow the steps below. 1.
Fig 1 Fig 2 Fig 3 2. Once your alarm host has been detected by the app the pair LED on the host will go out indicating that it was found. You will now be given the opportunity to name the alarm host (Fig 4) such as home, work, etc, prior to saving it. Now input the default host password 123456 and, tap save (Fig 4) to complete the setup.
Fig 2 Fig 1 2. Make sure your Smartphone or tablet is connected to the same Wi-Fi network that the alarm host is connected to and tap on the Broadcast in LAN option (Fig 3) to display all connected devices on our network (Fig 4). Now locate the serial ID associated with your alarm host (Fig 5) and tap on it to proceed. Fig 3 Fig 5 Fig 4 3. You will now be given the opportunity to name the alarm host (Fig 6) such as home, work, etc, prior to saving it.
AP MODE To add your alarm host to the HomeBot app using the AP Mode method, make sure your new alarm host in powered on and follow the steps below. 1. Tap on the AP Mode option (Fig 1) to begin the adding process. Turn your alarm host upside down then “Press and Hold” the pair button (Fig 2) until the pair LED located on the top of the host becomes solid. Fig 1 Fig 2 2.
Fig 6 Fig 7 4. Once all LED’s on the alarm hast turn off “Press and Hold” the power button on the host (Fig 8) until the power LED turns back on. Wait 40-60 seconds for the host to boot up and then press “Next” on the Smartphone prompt (Fig 9). Fig 8 Fig 9 5. Select the serial ID associated with your alarm host (Fig 10) and tap on it to proceed. You will now be given the opportunity to name the alarm host (Fig 11) such as home, work, etc, prior to saving it.
Fig 10 Fig 11 Fig 12 QR SCAN Please follow the steps below to add your alarm host to the HomeBot app using the QR Scan method. 1. Insert the female end of the AC adapter into the DC IN port (Fig 1) located at the bottom of the host and connect the other end into a wall outlet. Then connect one end of the Ethernet cable into the Ethernet port (Fig 1) (also located at the bottom of the alarm host) and the other end into your wireless router.
Fig 3 Fig 4 Fig 5 MANUAL INPUT Please follow the steps below to manually add your alarm host to the HomeBot app. 1. Insert the female end of the AC adapter into the DC IN port (Fig 1) located at the bottom of the host and connect the other end into a wall outlet. Then connect one end of the Ethernet cable into the Ethernet port (Fig 1) (also located at the bottom of the alarm host) and the other end into your wireless router.
Fig 3 Fig 4 3. Now name the alarm host (Fig 5) such as home, work, etc, input the default host password 123456 and, tap save (Fig 5) to complete the setup. Your device will now be displayed as the start screen whenever the app is launched (Fig 6). Fig 5 Fig 6 APP INFO Taping on the app info option will show you the App Version and Library Version of the HomeBot app currently installed on your Smartphone or tablet.
MODIFY SYSTEM The Modify System option is used to change the systems name, password (if entered incorrectly during setup) or delete the host from the app. HomeBot Control Center Features & Options The HomeBot Control Center lets you take control of your alarm system using your mobile device. Through the control center you can add, remove and control all sensors and accessories from your phone or tablet.
MAIN SCREEN SYMBOLS AND NOTIFICATIONS 1. Back 2. Sensor Status 3. Alarm Status BACK Used to exit the control center and return back to the start screen. SENSOR STATUS Represents the number of active/de-active devices per group (cameras, motion sensors, key remotes, etc). The first digit represents how many devices are enabled (active) and the second digit represents the total number of devices that have been added for that group.
ARM The arm icon is used to arm your system using your mobile device. Once pressed, the alarm status icon will change to “locked” and the host’s “arm” LED will turn red. SILENT ARM The silent arm icon is used to arm your system in ”Silent Mode” (no noise from siren of host) using your mobile device. Once pressed, the alarm status icon will change to “silent locked” and the host’s “arm” LED will turn red.
CAMERA (for Optional SM-821DTH & SM-825DTH models) The camera icon is used to add, remove, edit and control the cameras that have been added to your system. To add, edit or control your camera(s) simply tap on the camera icon as shown below. CAMERA OPTIONS AND SETTINGS (Optional Add-on Cameras) 1. Back 2. Device list area 3.
BACK Tapping on the Back Arrow will return you to the previous screen. DEVICE LIST AREA The device list area shows all the cameras that have been added. To login to a camera, simply tap on the camera you want to login too to bring up the camera live view as shown below.
CAMERA LIVE VIEW SETTINGS AND OPTIONS 1. 2. 3. 4. 5. 6. Back Snapshot Refresh Talk (2way) Record Camera Settings BACK Tapping on the Back Arrow will return you to the previous screen. SNAPSHOT Takes a snapshot of the current live view and saves it to your phones photo album.
REFRESH Refreshes the connection between the phone and the camera, and should only be used when the live view becomes frozen, disconnected or unstable. When utilized, the HOMEBOT application will reattempt to reconnect to the camera. TALK Pressing and holding the microphone icon allows you to speak to the person on the other end of the camera being viewed.
RECORD Pressing the recording icon will start and stop (when pressed again) manual recoding for the camera being viewed. The recorded events will be stored on to the cameras micro SD card which can be played back later by pressing on the camera settings icon. CAMERA SETTINGS Tapping on the camera settings icon will allow you to change the camera time, date, passwords, and much more. To configure these settings, tap on the gear icon, enter the default admin password 123456 and tap ok to proceed.
DID Firmware Version Check Upgrade Change Password Change Admin Pass Motion Detection Event List Loop Record Storage Management Video Rotation Set Date & Time WLAN DID The Device ID (DID) section provides you with the cameras ID which is used to add the camera to the app, unique to each device and is not configurable. FIRMWARE VERSION The Firmware Version section displays the cameras current firmware version and is not configurable.
VIDEO ROTATION Video Rotation allows you to change the cameras flip the live view so that you can mount the camera upside down. SET DATE & TIME The set date & time option allows you to set the cameras time and date when needed. WLAN The WLAN option is used to set to connect your camera to your personal WIFI network. Simply tap on the WLAN option and follow the onscreen step-by-step guide to do so. ADD CAMERA “+” The ADD “+” option is used to add or remove cameras to and from the alarm host.
BACK Tapping on the Back Arrow will return you to the previous screen. DEVICE LIST AREA The device list area shows all the devices that have been added. To rename or remove a device, simply tap on the device and follow the options on the edit screen. ADD “+” The ADD “+” option is used to add new device to the alarm host. To add a new device, please refer to the “Adding Devices and Cameras” section of this user’s manual.
BACK Tapping on the Back Arrow will return you to the previous screen. DEVICE LIST AREA The device list area shows all the devices that have been added. To rename or remove a device, simply tap on the device and follow the options on the edit screen. ADD “+” The ADD “+” option is used to add a new device to the alarm host. To add a new device, please refer to the “Adding Devices and Cameras” section of this user’s manual.
BACK Tapping on the Back Arrow will return you to the previous screen. DEVICE LIST AREA The device list area shows all the devices that have been added. To rename or remove a device, simply tap on the device and follow the options on the edit screen. ADD “+” The ADD “+” option is used to add a new device to the alarm host. To add a new device, please refer to the “Adding Devices and Cameras” section of this user’s manual.
BACK Tapping on the Back Arrow will return you to the previous screen. DEVICE LIST AREA The device list area shows all the devices that have been added. To rename or remove a device, simply tap on the device and follow the options on the edit screen. ADD “+” The ADD “+” option is used to add a new device to the alarm host. To add a new device, please refer to the “Adding Devices and Cameras” section of this user’s manual.
BACK Tapping on the Back Arrow will return you to the previous screen. DEVICE LIST AREA The device list area shows all the devices that have been added. To rename or remove a device, simply tap on the device and follow the options on the edit screen. ADD “+” The ADD “+” option is used to add a new device to the alarm host. To add a new device, please refer to the “Adding Devices and Cameras” section of this user’s manual.
BACK Tapping on the Back Arrow will return you to the previous screen. DEVICE LIST AREA The device list area shows all the devices that have been added. To rename or remove a device, simply tap on the device and follow the options on the edit screen. ADD “+” The ADD “+” option is used to add a new device to the alarm host. To add a new device, please refer to the “Adding Devices and Cameras” section of this user’s manual.
System Name Library Version Push Notification DID Check Upgrade Set Date & Time Firmware Version Change System Password Wi-Fi Networks SYSTEM NAME The System Name section is displays the name of the host and is not configurable through this part of the app. DID The Device ID (DID) section provides you with the host’s ID which is used to add the host to the app, unique to each device and is not configurable.
Specifications SM-025H Alarm Host Power DC5V 1.0A Backup Battery Built-in Lithium (up to 6 hours standby time) Network WiFi or Ethernet Transmission Frequency 433MHz Host Buttons [Top] Arm, Disarm, Power [bottom] On/Off switch, Reset, AP (access point) LED’s (red) Power, Arm, Pair Ports Power, Ethernet Antennas 1 x WiFi (left), 1 x 433MHz wireless (right) Size (LxWxH) 6.75” x 4.25” x 1.
ADD-ON (Optional): SM-105DB Battery Powered 3V (2 x AAA batteries included, last up to 1 year) Doorbell LED’s Red Transmission Frequency 433MHz Button 1 Size (LxWxH) 2.94” x 1.56” x .81” Transmission Distance up to 150ft with walls, 300ft clear line of sight SM-001SK Power Input AC100-240V Wall Socket Power Output Less than 10A Buttons Power On/Off, Pair/Register LED’s Red Transmission Frequency 433MHz Size (LxWxH) 4.25” x 2.5” x 1.
SM-821DTH Lens 1/4 “ CMOS color Pan-Tilt WiFi/ Sensor OV9712 Eth IP Camera Focal Length 3.6mm Pan-Tilt Control 260:Horizontal 120:Vertical (no zoom) Viewing Angle 50 degree System P2P (Cloud Technology) Video Compression H.264 Resolution 720P HD (1280x720), VGA (640x480), QVGA (320x240) Video Rate 30fps Motion Detection Yes Transmission Wired Ethernet or Wi-Fi NIC Interface 10/100Mbps (IEEE802.3, RJ45) Protocols TCP/IP, DHCP, SMTP,HTTP, UPNP WiFi Interface 802.
If you encounter any difficulty in the operation of this product after reading the manual, please feel free to contact us. You can reach us by phone at 1-888-977-3777 from 8:30 AM to 5:30 PM Monday through Friday (Pacific Standard Time) or by email techsupport@securitymaninc.com. We will be happy to answer your questions and help you in any way we can.
www.securitymaninc.
