Installation Guide

IWATCHALARM
Quick Start Guide
NOTE: All sensors included with your kit have already been paired/synced to the
alarm host and ready to go. Make sure you remove any plastic wraps from the
batteries provided before inserting them and mounting your sensors. Please refer
to each sensors syncing procedure if it does not show up on the Smartphone app.
Insert the female end of the AC adapter into the DC IN port located at the bottom
of the host controller and connect the other end into a wall outlet. Make sure you
use the cable management slots to help keep the cables organized.
Using a small flat head screw driver, gently pry open the back cover from the
emitting piece and Insert the AA battery provided, ensure the battery polarity is
correct (positive on positive). Once the battery is inserted re-attach the back
cover and test the sensor by separating the small magnetic piece from the flat
side of the emitting piece. You should get a flashing red light every time the two
pieces are separated.
NOTE: When mounting, please make sure the gap between the emitting and
magnetic is within 1/4 of an inch.
ALARM HOST (SM-025H)
DOOR/WINDOW SENSOR (SM-002M)
Using a Philips screw driver, remove the screw located at the bottom of motion
sensor, detach the front cover and insert the 2 AAA batteries provided, ensure
the battery polarities are correct (positive on positive). Once the batteries have
been inserted the blue LED should start to flash or stay solid indicating that it is
now operable. Re-attach the front cover and secure it with the screw. Mount the
mounting bracket with two screws provided to a desire location and slide the
motion sensor over and down to secure onto the mounting bracket.
MOTION SENSOR (SM-003P)
Step 1 HARDWARE
Step 2 SMARTPHONE SETUP
Insert the female end of the sirens AC adapter into the DC in port located behind
the siren and secure the siren to the wall using the screws provided. Once the siren
is securely mounted, plug the AC adapter into a wall outlet. Please note that the
siren is equipped with a tamper proof switch (located on the back) that will trigger
the siren to go off whenever the siren is lifted off the wall.
NOTE: Three AA batteries can also be used for back up purposes (batteries not
included).
Pop open the top and bottom panels to remove the clear plastic battery protection
before use. Once plastic is removed, close the top and bottom panels back together,
test the remote by pressing any button. The red LED should flash with each press.
INDOOR SIREN (SM-005SR)
REMOTE CONTROL (SM-007R)
1. Open the App Store on your mobile device. Then search for and install the
“HomeBot” application. Once installed, tap on the “HomeBot” icon (Fig 2.1), tap
the “+” icon located at the top right corner of the screen (Fig 2.2) and then select
the “Search in LAN” option (Fig 2.3).
2. Now select the Smart Config option (Fig 2.4) to begin the adding process.
Turn your alarm host upside down then “Press and Release” the AP button
(Fig 2.5). Once the pair LED located on the top of the host begins to flash rapidly
press next on the Smartphone prompt. When prompted, input the Wi-Fi
password of the network that you are currently connected too (Fig 2.6) and press
next. This will allow the app to smart configure the host using your current wireless
network.
3. Once your alarm host has been detected by the app the pair LED on the host
will go out indicating that it was found. You will now be given the opportunity to
name the alarm host (Fig 2.7) such as home, work, etc, prior to saving it. Now
input the default host password 123456 and, tap save (Fig 2.7) to complete the
setup. Your device will now be displayed as the start screen whenever the app
is launched (Fig 2.8)
Fig 2.1
INSIDE VIEW OF SENSOR
BOTTOM VIEW OF HOST
NOTE: Make sure that the ON/OFF switch
is moved to the ON position.
FRONT VIEW OF HOST
INSIDE VIEW OF SENSOR
Fig 2.2 Fig 2.3
Fig 2.4
Fig 2.7 Fig 2.8
Fig 2.5 Fig 2.6
NOTE: Make sure your Smartphone or tablet is connected to the same Wi-Fi network
as the one you want to put the alarm host on.