SecurityMan® NiteCam2 2.
Copyright Notice This manual is furnished under license and may be used or copied only in accordance with the terms of such license. Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or any means, electronic, mechanical, recording, or otherwise, including translation to another language or format, without the prior written permission of SecurityMan.
Warranty SecurityMan warrants that this product will be free from defects in materials and workmanship for period of time specified on the product packaging. This limited warranty shall commence from the date of purchase. SecurityMan products warranty is not transferable and is limited to the original purchaser. If the product is found to be defective then, as your sole remedy and as the manufacturer's only obligation, SecurityMan will repair or replace the product.
Notice: 2.4GHz wireless camera works at ISM band. It may cause interferences with other wireless equipment that operates with the same band. Please turn off one of the equipment to eliminate the interference. Product Assurance 2.4GHz wireless camera will emit electromagnetic wave, just like other wireless products. But the output power of the product is less than other wireless products such as mobile phones. The 2.
Conditions Please read the following messages to make sure whether your working environment is suitable. • Ensure there is enough space around the receiver for ventilation. • The temperature should be kept between -20°C and 50°C (-4°F-122°F). The relative humidity should remain from 20% to 80%.
CONTENTS Introduction 7 Package Contents 7 Technical Support 7 NiteCam2 Features 8 Installation Diagram 8 Product Basics 9 Installation & Setup 10 Camera Installation 13 Camera Channel Setup 14 Night Vision 15 Receiver Mode Setup 15 Channel set 16 Channel-scan set 16 Specifications 18 Troubleshooting 19 6
Introduction Thank you for purchasing the NiteCam2 2.4GHz wireless indoor/outdoor bullet color camera kit with night vision and audio. It consists of two vivid CMOS color camera with night vision (B/W) and audio, and a compact 4-channel receiver with sharp 380 TV lines picture display output. The camera converts video and audio signals into radio signals and transmits them to the receiver, which then, can be input to TV,VCR or DVR for crystal clear sound and picture to monitor your home or business.
NiteCam2 Features • Perfect for monitoring around your home or business • Wireless video direct to TV, VCR, or DVR • 380TV lines sharp picture display • Built-in IR LEDs for night vision (up to 23ft) • Weather-proof design for outdoor use • Selectable 4-channel supports up to 3 cameras • Built-in microphone for audio monitoring • Up to 100 feet away indoor or 300 feet away with clear line of sight Installation Diagram 8
Product Basics Camera Receiver 9
Installation & Setup 1) Connect the adapter (DC 8V 300mA) to the camera. Power Outlet 2) Set the camera to desired channel. 3) Connect the antenna to the receiver.
4) Connect the receiver to a monitor/TV with AV cable (yellow for video and red audio). Turn on the monitor/TV and select AV mode. 5) Connect the power jack of adapter (DC 7.5V 300mA) to receiver. Press the Power ON/OFF button and the channel indicator lights up green.
6) 7) Press the Channel Select Button “CH” on the receiver until the channel indicator matches to the channel on the corresponding camera, and monitor/TV will display pictures. Adjust the brightness, contrast and color of the monitor/TV for the perfect effect.
Camera Installation 1. Locate where you would like to install the camera Please follow the steps below to install the camera to a wall or ceiling. 1.1 Secure the three screw anchors into wall (or ceiling) to match the hole pattern in the camera bracket 1.2 Align holes in the camera bracket and the anchors, and secure the camera on the wall with three screws 2. Adjust the angle 2.1 Unscrew Fastener 1, adjust the camera to an appropriate angle, and then fasten it. 2.
Note: If camera is being installed on to the ceiling, it is recommended to remove the angle bar and connect the universal bracket with the camera directly. Angle bar Camera Channel Setup This camera has 4 selectable channels to avoid possible interference from other nearby wireless devices.
Night Vision The built-in Infra-red lights in camera provide 7m night vision range for 24hrs surveillance. The Infra-red lights will be automatically activated at night or in dark places. The picture will turn Black & White (monochrome) in Night Vision mode. Receiver Mode Setup The receiver can support up to 4 cameras working at the same time. You are allowed to set the Mode Control as described below. The Mode Control has the precedence over other buttons.
Channel Set You can confirm which channel is set to receive signal from corresponding camera. With this function, you could set the unused channels to OFF, so that they will be skipped during the Manual mode or Channel Scan mode.
1. Manual mode: Slide Mode Control switch to M to enter Manual mode. In this mode, the receiver channel won’t change until you press the Channel Select Button “CH” Tip: Channel-Scan function can also be activated by pressing and holding the Channel Select Button "CH" for more than 5 seconds in Manual mode. Press the Channel Select Button again to deactivate Channel-Scan function. 2. Channel Scan mode: Slide Mode Control switch to L to enter channel scan mode.
Specifications of Camera (SM-202T) Image Sensor CMOS Total Pixels View Angle Minimum Illumination Gain Control Frequency Transmission Power Modulation ModeBandwidth Power Supply Consumption Current Unobstructed Effective Range Night Vision Range Operation Temperature Storage Temperature Operation Humidity Microphone Weatherproof Rating 1/4-inch CMOS 510 X 492 (NTSC) 45-50° 3 Lux/F2.
Troubleshooting Abnormal Phenomena Possible Reasons/Solutions *Check the camera / receiver connected to power supplies, and power on. *Check if the channel of receiver is corresponding to camera; *Check the distance and blocks. *Interfered by other sources; *Check the distance and blocks. *Interfered with other devices nearby; Remove or turn off such devices. EU Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
www.securitymaninc.