SolarPIR™ User’s Manual Indoor Motion Detection Alarm with Solar Panel
© Copyright 2011 This manual is furnished under license and may be used or copied only in accordance with the terms of such license. Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or any means, electronic, mechanical, recording, or otherwise, including translation to another language or format, without the prior written permission of SecurityMan.
Warranty Disclaimers SecurityMan Inc, makes no other warranties, express, implied or otherwise, regarding this product, and specifically disclaims any warranty for merchantability or fitness for a particular purpose. The exclusion of implied warranties is not permitted in some states and the exclusions specified herein may not apply to you. This warranty provides you with specific legal rights. There may be other rights that you have which vary from state to state.
Table of Contents Introduction 4 Important 4 Restrictions 4 Conditions 5 Package Contents 6 Specifications 7 Features 7 Product Basics 8 Setup and Operation 9 9 Installating Batteries Security Code 10 Mounting SolarPIR™ 10 Operation 12 Troubleshooting 13 3
Introduction Thank you for going green with the SecurityMan SolarPIR™. This motion detection driven alarm can be used to help protect your home and business with the comfort of its energy saving solar panel design and AA battery backup (x3 not included). The technology used in these solar panels is used to recycle indoor lighting (100+ Lux) as a source of power to help conserve and extend the battery life of the AA batteries to up to three years.
• DO NOT put the plastic package bags in reach of children or babies. Young children can choke on these items if they put them into their mouths. • DO NOT use rechargeable batteries. This device is not intended to be recharged. • DO NOT use it aboard; please abide by the airway’s provision. It might influence communication aboard and the flying apparatus if departing from the airway’s regulation. This will result in accident, possible death and severe physical hurt.
• It might influence the normal operation of the product if used at the fringe range of normal temperature. Please turn off the power when not in use. • Do not disassemble the product. • Do not shake or strike the product. • Please obey the local government’s environment protection policy.
Specifications PIR Range Detecting Angle Operating power Power Consumption Solar Lighting Alarm Sound Maximum Alarm Time Pet Immunity Security Dimensions 8m/26ft 40° horizontal, 75° vertical 3 x AA (1.5v) Alkaline Batteries 20uA 100 Lux (minimum) 130dB 30 Seconds 11 lbs.
Product Basics Solar Panel Low Battery Indicator Key Pad Motion Sensor Battery Compartment Siren 8
Setup and Operation Installing Batteries Use a Philip screw driver to remove the back panel to get to the battery compartment as shown below. Insert 3 x AA size batteries (not included) into the battery compartment; make sure the polarities are correct when installing the batteries. Don’t put the rear panel back on yet until SolarPIR is ready to mount as illustrated in the next two sections below.
Security Code The SolarPIR comes with a security code that can be use to arm the alarm motion sensor when away from home and disarm the alarm motion sensor when entering. The manufacturer default security code for the alarm motion sensor is 1234. To change the 4 digit Security Code please do the following: • Input the factory default security code “1234” (the red LED will start to flash for 30 seconds indicating that the unit is in programming mode).
3. Hold the SolarPIR to hover over the mounting bracket and then slide it downward to lock the SolarPIR to the mounted bracket. 4. Secure the SolarPIR to the mounting bracket by using the screw provided to the base of the alarm siren as illustrated below.
Operation Arming the PIR To arm the SolarPIR, simply press the number 4 on the keypad. At this time you will hear a confirmation tone which indicates that the PIR has been successfully armed. 30-Second exit delay Once armed, you have 30 seconds to vacate the protected area before the PIR becomes active. Any motion detected after exit delay time has expired will trigger the alarm.
IMPORTANT NOTICE: The 4 digit security code will be defaulted back to the preset factory code 1234 every time the batteries are replaced. Troubleshooting Q1: The unit does not beep when the last battery is installed? Make sure that you are using new batteries and that they are installed properly. Q2: The red light on the alarm unit is ON. This is an indication that the batteries are running low. Please replace all batteries with new ones.