www.seeedstudio.com www.seeed.
ODYSSEYUser Manual X86J4105
Package Contents SATA PWR ODYSSEY - X86J4105 User Manual x1 International Power Adapter x 1 SATA Cable x 1 Antenna x 2 RTC Battery x1 Heat Sink (Assembled) x 1 Cooling Fan (Assembled) x 1 • ODYSSEY - X86J4105 • User Manual • International Power Adapter • SATA Cable • Antenna x2 • RTC Battery • Heat Sink (Assembled) • Cooling Fan (Assembled) (Included in EMMC version)
Specifications Processor Coprocessor Graphics Memory Storage Wireless Networking Audio Headers Intel® Celeron® J4105 Frequency: 1.5 – 2.5GHz Microchip® ATSAMD21G18 32-Bit Arm® Cortex® M0+ Intel® UHD Graphics 600 Frequency: 250 – 750MHz LPDDR4 8GB 64GB eMMC V5.1 Wi-Fi 802.11 a/b/g/n/ac @ 2.4/5 GHz HT160 Bluetooth® 5.
USB 2.0 Type-A x2 USB USB 3.1 Type-A x1 USB 3.1 Type-C x1 HDMI2.0a: Up to 4096x2160 @ 60Hz 24bpp Video Interfaces DP1.2a: Up to 4096x2160 @ 60Hz 24bpp M.2(Key B, 2242/2280): SATA III, USB2.0, UIM M.2 (Key M, 2242/2280): PCIe 2.0 ×4 Expansion Slots Micro SD card Socket SIM Card Socket SATA III RTC JST 1.0 CR2032 3V TPM Built-in TPM (2.0) DC Jack 5.5/2.
Quick Start with ODYSSEY - X86J4105 Before you Start 1 2 Make sure you have the following: 1 An external monitor 2 A keyboard and a mouse 3 An HDMI Cable 3
Attaching External Storage If you have bought the 64GB EMMC storage version of the ODYSSEY - X86J4105, you can skip this step. However, if you need more storage for your needs, feel free to follow this step. There are four methods of adding storage to ODYSSEY - X86J4105 1 Through M.2 PCIE Connector 2 Through M.2 SATA connector 3 Through SATA Connector 4 Through Micro SD Card Slot 1 M.2 PCIE SSD 4 Micro-SD SATA PWR M.
Connecting Antennas Insert the two antennas into the two sockets on the ODYSSEY - X86J4105 Note: One antenna is for Wi-Fi and Bluetooth whereas the second antenna is for strong 5G connectivity Connecting to a display 1.
Connecting to a keyboard and a mouse Connect your favorite keyboard and mouse to the ODYSSEY - X86J4105 through any of the USB connectors
Powering up 1. There are two ways to power up your ODYSSEY - X86J4105.
2. Press the power button and you will notice the blue power LED turn on 3. Wait a few seconds until it boots into the operating system.
Installing an Operating System ODYSSEY - X86J4105 supports both Windows and Linux operating systems. If you have bought the non EMMC version, you could attach an external storage by following the previous steps and install your desired operating system by creating a bootable USB drive. Also, if you have bought the EMMC version with windows pre-installed, you could additionally install Linux according to your requirements.
Step 2 Press the power button and keep pressing F7 key on the keyboard until you see the Boot Manager screen. F7 Step 3 Select the connected USB Drive as the boot drive and press enter Please select boot device: UEFI: Built-in EFI Shell Windows Boot Manager UEFI OS (USBStick 16GB) Enter Setup and to move selection ENTER to select boot device ESC to boot using defaults Step 4 Then follow the instructions on the installation screen to complete installing your desired operating system.
Adding 4G Cellular Connectivity Step 1 Insert a standard SIM Card to the bottom layer of the slot. SIM Step 2 Insert a PCIE 4G module. Note: This module is a must have if you want to use the connected SIM card.
Pinout diagram Solder pads at the back RX TX PWR GND LED+ LED- ODYSSEY- GND RST TX RX D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 1 2 3 4 5 6 A0 A1 A2 A3 A4 A5 SDA SCL 7 8 9 10 11 12 13 14 15 16 17 18 MOSI 19 20 21 22 MISO 23 24 25 26 27 28 1 5V 5V GND 8 GPIO 493 TX 10 GPIO 492 RX 12 GPIO 338 14 GND 16 GPIO 421 18 GPIO 422 20 GND 22 GPIO 390 24 GPIO 356 FS0 26 GPIO 357 FS1 28 GPIO 389 SCL 30 GND 32 GPIO 391 34 GND 36 GPIO 410 38 GPIO 340 40 GPIO 341 CLK 3V3 5V GND SW S
FAQ Q: How can I access the BIOS setup? A: Press the Power Button and keep pressing DEL key until you see the Q: A: BIOS Setup. Arduino IDE doesn’t recognize the onboard microcontroller Add a jumper wire between pins 3 and 4 of UART pins on the 28-pin header to reset the AMSAMDG21. Q: I cannot connect to Wi-Fi and Bluetooth A: Check BIOS settings and enable Wi-Fi and Bluetooth from BIOS.
