Operation Manual

2. PROGRAM PLAY
Press the PLAY/PAUSE button on the unit (or remote control). The unit will play the first track
of the program. When all tracks have been played, the unit display will be shows the number of
tracks and the playing time of the CD/MP3 songs.
3. CANCEL PROGRAM
Press the STOP button once, or open the CD tray door and close it again that the memory will be
erased. Set a new program, the and the existing one will be cleared
UK-8
AU X PLAY(Aux in cable not included)
Slide the FUNCTION switch until the "AUX” indicator light on the display. This unit can input
analog audio through these jacks. Use a cable with RCA phone plays to connect audio equipment.
Note : During in the program mode.
1. Press the "PLAY MODE" button once, the " " indicator will light on the display
. Then the unit will
repeat the current track.
2. Press the "PLAY MODE" button twice, the " " will l light on the display. Then the unit will
repeat all the total number of tracks.
3. Press the "PLA
Y MODE" button once more again. The unit will return to play the program in
normally.
ALARM CLOCK OPERATION
During the unit in STANDBY mode :
To set the correct "ALARM 1 or 2" :
1. Press the “ALARM 1 or 2 SET/OFF " button once on the remote control. The "AL 1 or 2 BELL
SYMBOL" indicator will light on. Press the "ALARM 1 or 2 SET/OFF" button one more time and
hold it for a few seconds, then the "HOUR" indicator will flash. Adjust to the correct "HOUR" by
pressing the "SKIP/SEARCH" (UP or DOWN) button.
2. Press the “ALARM 1 OR 2 SET/OFF" button again. The "MINUTE" indicator will flash. Adjust to the
correct "MINUTE" by pressing the "SKIP/SEARCH" (UP or DOWN) button.
3. Select your preferred alarm code by sliding the Function switch on the main unit.
4. Press the “ALARM 1 OR 2 SET/OFF” button repeatedly to confirm the "ALARM 1 OR 2" function;
the "HOUR/MINUTE" indicator will flash and switch to "CLOCK",and then the "AL 1 OR 2 BELL
SYMBOL" indicator will light on the LCD display
.
Note: 1. There is no alarm setting in AUX Mode.
2. The buzzer will alarm under the CD mode if no CD in the compartment. The same under the
USB mode and SD card mode, if no USB and SD card.
3. Yo
u should enter into the USB mode and SD card mode before setting alarm under USB
mode and SD card mode.
SNOOZE FUNCTION
1. Press the SNOOZE button after the TUNER, CD, USB, SD CARD or BUZZER alarm sounded. The
alarm will go off and will come on again in approximately 9 minutes.
2. Press and hold the “SNOOZE” button around 2 seconds, the SNOOZE will flash on the display,
then press the SKIP/SEARCH (UP or down) button to set the SNOOZE time.(the second alarming
time after the set time from 1 minute to 20 minutes.)
3. The alarm will keep alarming 60 minutes, if no button pressed; however
, all set SNOOZE time will
go of
f automatically after 60 minutes.
NOTE :1. When the bell is ringing, you can press the "STANDBY" button once or press the “ALARM 1
SET/OFF or ALARM 2 SET/OFF" button once on the remote control to stop the "ALARM 1 or
2" function. The “AL 1 or 2 BELL SYMBOL" indicator will still light on the LCD display
.
(It may keep the "ALARM 1 or 2" function in next day)
2. When the bell is not ringing, if you want to stop the "ALARM 1 or 2" function fully
, you can
press the “ALARM 1 SET/OFF or ALARM 2 SET/OFF” button once on the remote control
only
. The “AL 1 or 2 BELL SYMBOL” indicator will turn off on the display. The function of the
“ALARM 1 or 2" will cancel at once.