2-WAY REMOTE STARTING SYSTEM WITH 1 BUTTONS FOR AUTOMATIC TRANSMISSION RED301-2WAY / MA1000-2WAY3 User Guide For Key
WARNING It is the responsibility of the vehicle operator to ensure that their vehicle is parked in a safe and responsible manner. 1. When leaving the vehicle, it is the user’s responsibility to ensure that the gearshift lever is in “Park” in order to avoid accidents upon remote starting. (Note: Make sure that the automatic vehicle cannot start in “Drive”.) 2. It is the user’s responsibility to ensure that the remote starter is disabled or put into valet mode before servicing.
Using the remote control Description of Remote Appearance Lock, Unlock and Remote Lock, Unlock and Remote Starting icon is displaying with Starting icon is displaying with One LED color. Two LED color. Lock/Unlock Note: Press the button 1 time on the remote control transmitter to lock the vehicle. Press the button 2 times to START/STOP: unlock the driver’s door, 2 additional Note : Remote Engine Start - times to unlock all doors.
Vehicle Presets Heater When leaving the vehicle it is recommended to preset the accessory controls in preparation for the Next remote start. Settings for the blower motor(fan),front and rear (if equipped),should not be left on HIGH. It is recommended to leave the settings on LOW or MEDIUM instead. Windshield Wipers, Headlights Certain vehicles require the windshield wipers and headlights circuits to become energized while running under remote start.
Note: LED icon of 2way transmitter indicates firstly blue color and then change to “RED” color when you press any button. In this case, it’s time to change CR2025 battery newly Description of Antenna Appearance 2Way Antenna Antenna Harness Note: Use the power of the antenna car battery 12volts.
Remote-Starting your Vehicle Remote-Starting For the 2-way remote: 1. Press the button one time. The remote will beep once and display the Lock icon. Then, press the button within 2 seconds. The remote will beep once and display the KEY icon. 2. 5 seconds later, the remote will activate starter. The Key icon will be shown with 3 different tones of beeping then the LED Icon will be scrolled.. For the 1-way remote: 1. Press button one time and Lock LED will be displayed.
2. Press the brake pedal to disengage the remote starter unit. With the vehicle key is in the IGNITION ON position, press the brake pedal or wait 30 seconds for the vehicle to turn to ready status to drive. Note: In remote engine start status, engine will be deactivated according to following conditions. - Open the door and 30 seconds is passed. - Press brake pedal without key is in IGNITION ON position.
Valet/Service Mode For REMOTE Start KEY Fob Valet/Service mode is used to prevent the system from unexpectedly starting the engine while being serviced. When your vehicle is in Valet Mode, the remote starter functionalities are disabled. If the vehicle needs to be serviced, or if you park it indoors, the Valet Mode will prevent the engine from being remote-started accidentally.
Caution: The programming of your system should be left to a professional. Changing any one of the settings may affect the operation of your Remote Car Starter. Engine Run Time setting Option Setting Condition Disarm the vehicle with remote control transmitter.(Unlock) Driver s door must be physically Open, Engine Stop, Ignition ON, Trunk Open and Hood Open. Option Setting Instruction - Under option setting condition, press button for 2 seconds.
1. When a new registration is needed - When replacing a remote due to loss or malfunction of a remote. - When replacing the main controller installed in the vehicle. - When adding or changing the remote upon user’s need. 2. Pairing procedure RS Fob X1 5X 1) Open driver’s door and trunk. 2) Insert the key into the ignition. Turn the key from OFF to ON position 5 times within 5 seconds. 3) After step 2), within 5 seconds, Press button on the 1st Remote Start Fob 1 time.
Troubleshooting Poor Transmitting Range Many factors may affect the operating range of the transmitter. Some of these are: -The condition of the batteries in the transmitter. -The operating environment (for example: downtown radio-frequency noise, airports, cellular phone towers, etc). -Metal in the area of the vehicle of transmitter. This includes the vehicle itself. -The shape of the vehicle can affect range as well. Vans in general have greater interference.
