Use er Ma anual By Firste ech LLC, Ve ersion: 1.0 Ap pplicable to o the follow wing remote e(s); 2W WR5-SF 2W Way 1Button LED Rem mote Model N Name 2WR5R- SF ANT-2W WSF FCC ID IC C Number VA A5REK500-2WLR 7087A A-2WREK500 0LR VA A5ANH500-2 2WLF 7087A A-2WANH500 0LF WWW W.COMPUST TAR.
WARNING It is the responsibility of the vehicle operator to ensure that their vehicle is parked in a safe and responsible manner. (1) When leaving the vehicle, it is the user’s responsibility to ensure that the gearshift lever is in “Park” in order to avoid accidents upon remote starting. (Note: Make sure that the automatic vehicle cannot star in “Drive”.) (2) It is the user’s responsibility to ensure that the remote starter is disabled or put into valet mode before servicing.
Introduc ction T Thank you fo or purchasin ng a Firstecch system fo or your vehicle. Please take a minu ute to review w this entire e m manual. Notte that this manual m applies to the 2 Way 1 Buttton Remote es whether you y purchassed the A ALARM IT, S START IT, o or MAX IT ssystem. Thiss manual alsso supportss the 1 Way Remote tha at is include ed w with your RF F Kit. There are certain features lissted in this manual m that may not be e available ffor your ssystem.
Quick Reference Remote Maintenance – Battery Charging The 2WR5-SF comes with a rechargeable battery. Use the included power adapter and micro USB cable to charge your remote. First, locate the micro USB port on the top of your remote. Connect your micro USB cable to your computer or USB power adapter. The LCD on the front of the remote will showing that your remote is charging. This should take approximately 2 hours.
G General Features T The remote transmitter functions are predeterm mined and p programmed from the ffactory. The e one button n cconfiguration n allows for many functtions to be p performed th hrough a se eries of tapp ping and/or holding b buttons. S Sending Co ommands W When in range and a co ommand ha as been sent, the remotte will receivve a page back b and LE ED cconfirmation n. For examp ple, to send d a remote sstart comma and from the e 2 Way rem mote, hold d down the button fo or 3 second ds.
Manual Transmission Remote Start Function (Reservation Mode) In order to remote start a manual transmission vehicle, the system must first be set in Reservation Mode. Reservation Mode must be set each and every time you want to remote start a manual transmission vehicle. The purpose of Reservation Mode is to leave the transmission in neutral before exiting the vehicle. IMPORANT: The FT-DAS must be installed and working properly. The transmission must be left in the neutral position.
FT-DAS STEP 1: Turn the ignition to the ‘on’ position. STEP 2: 2 Way remotes-hold buttons 1 and 2 (Lock and Unlock) for 2.5 seconds. You will get two parking light flashes. 1 Way remotes-hold Lock and Unlock for 2.5 seconds. You will get two parking light flashes. STEP 3: To set the Warn Away Zone 1, tap button 1. (1 Way: Lock) After you get one parking light flash, tap the vehicle. You will get siren chirps 1-most sensitive through 10-least sensitive. This sets the impact sensitivity of Warn Away Zone 1.
Alarm rearm and lock To rearm, hold your finger on the ‘Red Circle’ for 2.5 seconds. Alarm disarm and unlock To disarm, hold your finger over the ‘Red Circle’ for 2.5 seconds. Once the LED’s start their circular pattern, enter your 4 digit code. (Refer to Step 4 above.) Two seconds after entering the 4th digit, your system will disarm. 2 Way LCD remote paging To page a 2 Way LCD remote just tap the ‘Red Circle’ twice.
D Description of a antenna a module installation p position n < << Antenna a Module >> > << H Harness >> << Insta allation of A Antenna Module >> N Note: Use th he power off car batteryy(+12volts). The A Antenna mo odule have b been calibra ated for horizontal insta allation at the left-top co orner of the windsshield. Installing g the Anttenna Mo odule. S STEP 1: Set tthe controllerr option 1-14 4 to setting 4.
R Remote Coding g / Programmin ng Routine IM MPORTANT: Every Firrstech remo ote must be coded to th he system prior p to perfo orming any operations. o All re emotes musst be coded d at the sam me time. P Programm ming 2 W Way 1 Bu utton Rem motes: S STEP 1: Acttivate Valet//Programmiing mode byy manually turning t the ignition keyy on and off (between th he A Acc & On po ositions) five e times within 10 secon nds.
Remote Start Shutdown Error Codes If the remote start sequence has been completed and the vehicle shuts down, the vehicle’s parking lights will flash 4 times, pause then flash again with the error code. Tap button 4 on 2 Way remotes to initiate the shutdown error codes. On 1 Way remotes hold the Trunk and Start buttons together for 2.5 seconds.
DESCRIBED ABOVE. Your Warranty The product's warranty is automatically void if the date code or serial number is defaced, missing or altered. This warranty will not be valid unless you have completed the registration card at www.compustar.com within 10 days of purchase.
