NF02603-1.0 All rights reserved to SEIKAKU. All features and content might be changed without prior notice. Any photocopy, translation, or reproduction of part of this manual without written permission is forbidden. Copyright c 2006 SEIKAKU GROUP No.1, Lane 17, Sec. 2, Han Shi West Road, Taichung, 401 TAIWAN Tel:886-4-22313737 Fax:886-4-22346757 http://www.show-pa.com e-mail: sekaku@sekaku.
All rights reserved to SHOW. All features and content might be changed without prior notice. Any photocopy, translation, or reproduction of part of this manual without written permission is forbidden. Please read this manual carefully before operating this unit for the first time.
17 Unplug this apparatus during lightning storms or when unused for long periods of time. Power Supply Ensure the source voltage matches the voltage of the power supply before turning ON the apparatus. WARNING CAUTION: Describes precautions that should be observed to prevent danger of the apparatus. Disposing of this product should not be placed in municipal waste and should be separate collection.
Don't use solvents such as benzol, alcohol, or other fluids with very strong volatility and flammability for cleaning the apparatus body. Clean only with dry cloth. When the apparatus needs a cleaning, you can blow off dust from the apparatus with a blower or clean with rag etc. Cleaning Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. A polarized plug has two blades with one wider than the other.
470~496 6.2 Frequency Ranges 15 Most countries closely regulate the radio frequencies used in the transmission of wireless information. These regulations state which devices can use which frequencies, and help to limit the amount of RF(radio frequency)interference in all wireless communications. To be flexible enough to operate worldwide, UL-82DR Wireless receivers are available in a number of models, each with a unique frequency range.
Dynamic(S-100) Dynamic(S-600) Dynamic(S-500) Condenser(C-100) Condenser(C-200) UL-81H/UP-881H UL-83H/UP-883H UL-86H/UP-886H UL-87CH/UP-887CH UL-88CH/UP-888CH 1 Capsule Model No. UL-H series Handheld Transmitter To well satisfy the different applications , there are included in this product range, please make sure that the proper microphone has been selected for your typical sound reinforcement system before installation.
-100dBm/30dB SINAD unbalanced 6.3mm phone jack 550mV ; RF sensitivity Audio output DC 12V/500mA Power supply Weight 13 217(W)x101.5(D)x44(H)mm (8.5"x4.0"x1.7") 0.54Kg Dimensions AC (115V/120V/230V 50/60Hz Adaptor) 1V, 20KHz deviation balance output 20KHz deviation >90dB >100dB Dynamic FM (F3E) S/N Ratio 1KHz <0.8% 0.005% (-10 ~ 50) Frequency stability Modulation mode 50 Hz-15KHz ( 3dB) Frequency response T.H.D.
C-100 Type: Condenser Mic. Frequency response: 50Hz~15kHz( 3dB) Impedance: 270 20% at 1kHz Sensitivity: -71dB 3dB Direction: Omni-directional S-500 Type: Dynamic Mic. Frequency response: 90Hz~12kHz( 3dB) Impedance: 680 20% at 1kHz Sensitivity: -52dB 3dB Direction: Uni-directional C-200 Type: Condenser Mic.
680 ohm 50-12 kHz; -65 dB 3 dB at 1kHz 12 180 mm( 0.47" 7.1") 22g(0.049Ib) 3 Last but not the least, the operating frequency of this wireless system may be varied from 470MHz to 900MHz, please refer to your national EMC regulations to pick out the authorized frequency band (F1 ~ F8, detail please see Annex hereafter) for your end application. HM-38, Condenser microphone Preset impedance: 600ohm; Freq. response: 80-12KHz; Sensitivity: -68dB+/-3dB at 1KHz; Directional: Uni-directional; Weight: 52g (0.
Fig 6: UNLOCK 11 4) Use the Select key to set the proper channel. 3) Touch the CH/ON key slightly to select the parameters to be edited; 2) Switch on the transmitter; 1) Check the preset frequency (preset channel) displayed on the receiver. - Adjust from the transmitter, UL-H series receiver. 4.2.2 To make the operating frequency matched between the transmitter and the Fig 5: LOCK The transmitter has lock function. It can avoid the misaction during the application.
3 4 6 2 1 5 2 MENU key Press the MENU key to switch channel 1 and channel 2. When channel 1 is selected, use the UP/DOWN key to select the right frequency. Press the MENU key again, it switched to channel 2. The frequency setting mode of channel 2 is the same as that of channel 1. Keep pressing the MENU key for 1.5 seconds, it comes to the auto SQ mode. When the right frequency is selected, 1 UP/DOWN key Use the UP key to scan the frequency presets from 0 to 99 and the DOWN key from 99 to 0.
9 The job of a squelch circuit is to reduce audible noise. It eliminates noise during pauses in the audio signal by muting the receiver every time the audio level drops below a defined threshold. The squelch control on the receiver sets this threshold. Use the squelch control with care! If the squelch threshold is too high, the squelch will not only cut out noise but mute quiet audio signals as well because the squelch responds to the detected voltage and cannot distinguish between wanted signal and noise.
DC 9V 1 2 5 8 6 7 7 2 CH/ON Key Keep pressing this key for a few seconds, the unit will be powered on or off. After it is switched on, touch this key slightly to select the parameter which you want to edit, such as the preset channel, PL(RF power level) and Lock/Unlock. In this mode, if there is no further operation in the next few seconds, it will return to the main menu, and the LCD displays again the current preset channel, as well as the battery status.
