USER MANUAL SM40UNP SEIKI.
Contents BEFORE USING THE PRODUCT 3 4 5 Cleaning Securing the Installation Space Correct Posture to Use the Product SAFETY INFORMATION 6 7 8 Symbols Electrical Safety Installation Safety PREPARATIONS 11 12 What’s Included Installation CONNECTIONS 14 14 Before Connecting Connecting PC INITIAL SETUP 18 Before Using the Monitor OSD MENU SETTINGS 19 20 21 22 23 24 25 26 SOURCE LANGUAGE PICTURE COLOR PIP/PBP AUDIO SETUP OSD SETUP SPECIFICATIONS 27 28 29 General PowerSaver Standard Signal Mode
Before Using the Product Cleaning Exercise care when cleaning as the panel and exterior of advanced LEDs are easily scratched. Take the following steps when cleaning. 1. Power off the monitor and computer. 2. Disconnect the power cord from the monitor. Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result. 3. Wipe the monitor screen using a clean, soft and dry cloth.
Before Using the Product Securing the Installation Space Ensure some space around the product for ventilation. An internal temperature rise may cause fire and damage to the product. Be sure to allow the amount of space as shown below or greater when installing the product. The exterior may differ depending on the product. 3.93” (10 cm) 3.93” (10 cm) 3.93” (10 cm) 3.93” (10 cm) 3.
Before Using the Product Correct posture to use the product 50 cm • Straighten your back. • Allow a distance of 45 to 50 cm between your eyes and the screen, and look slightly downward at the screen. • Keep your eyes directly in front of the screen. • Adjust the angle so light does not reflect on the screen. • Keep your forearms perpendicular to your upper arms and level with the back of your hands. • Keep your elbows at about a right angle.
Safety Information Caution: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL. Symbols This symbol indicates that high voltage is present inside. It is dangerous to make any kind of contact with any internal part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product.
Safety Information Electrical Safety The following images are for reference only. Real-life situations may differ from what is shown in the images. Warning Do not use a damaged power cord or plug, or a loose power socket. • An electric shock or fire may result. Do not plug many products into the same power socket. • Otherwise, the socket may overheat and cause a fire. Do not touch the power plug with wet hands. • Otherwise, an electric shock may result. Fully insert the power plug in case it’s loose.
Safety Information Installation Safety Warning DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES. • Otherwise, a fire may result. Avoid installing the product in a narrow space with bad ventilation, such as a bookshelf or wall closet. • Otherwise, a fire may result due to an increased internal temperature. Keep the plastic packaging bag for the product in a place that cannot be reached by children. • Children may suffocate.
Safety Information Installation Safety Warning High voltage runs through the product. Do not attempt to disassemble, repair, or modify the product on your own. • An electric shock or fire may result. • Contact Seiki Customer Service Center for repair. Before moving the product, turn off the power switch and disconnect the power cable and all other connected cables. • Otherwise, the power cord may be damaged and a fire or electric shock may result.
Safety Information Caution Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels. • If you are not going to use the product for an extended period of time, activate power-saving mode or a moving-picture screen saver. Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc.).
Preparations What’s Included • Contact the dealer from whom you purchased the product if any item is missing. • The appearance of the components may differ from the image shown. Display Panel Base Stand Power Cord DisplayPort Cable HDMI Cable USER MANUAL QUICK SETUP GUIDE 002-BA8-SEIKI SM40UN P SEIKI. com Quick Setup Guide © Copyright 2014 SEIKI, LLC All rights reserved. User Manual Disc • Components may vary depending on the country.
Preparations Installation Attaching the Stand • Before assembling the product, place the product down on a flat and stable surface. When inserting the stand,aim the groove directly to the convex on the base, then anticlockwise rotate the stand to the end. Fasten the connecting screw at the bottom of the stand base. Push the assembled stand into the main body in the direction of the arrow as shown in the figure.
Preparations Removing the Stand • If you already fasten the 2 screws on the back of the mounting plate, be sure to loosen them first. • Before removing the product, place the product down on a flat and stable surface. Toggle the lever on the stand, then pull the assembled stand out of the main body in the direction of the arrow as shown in the figure. Loosen the connecting screw at the bottom of the base. Clockwise rotate the stand and pull it out of the base in the direction shown in the figure.
Connections Before Connecting Connection Using the DVI Cable • Before connecting a source device, read the user manual provided with it. The number and locations of ports on source devices may differ from device to device. • Do not connect the power cable until all other connections are completed. Connecting the power cable during connection may damage the product. • Check the types of ports at the back of the product you want to connect.
Connections Connection Using the HDMI Cable HDMI Connection Using the DisplayPort (DP) Cable HDMI 1. Connect the HDMI cable to the HDMI 1 or HDMI 2 port on the back of the product to the HDMI port on the PC. 2. Connect the power cable to the product and a power socket. Next, turn on the power switch on the PC. 3. Change the input source to HDMI 1 or HDMI 2 by touching / , when input source is not set. DP DP 1.
Connections Connection Using the VGA Cable Connecting the Built-in USB Hub USB VGA VGA 1. Connect the VGA cable to the VGA port on the back of the product and the VGA port on the PC. 2. Connect the power cable to the product and a power socket. Next, turn on the power switch on the PC. / , when 3. Change the input source to VGA by touching input source is not set. USB PC-USB USB DEVICES 1. Connect the USB cable to the PC-USB port on the back of the product and the USB port on the PC. 2.
Connections Connecting the Power Connecting to Headphones or Speakers • PC AUDIO LINE OUT DP HDMI HDMI Connect the power cable on the rear of the product. Plug in the power cable to the power socket. AC Outlet DP OR AC IN OR OR 1. Connect the Mini Audio cable to the PC AUDIO/HDMI/DP port on the back of the product and the AUDIO/HDMI/DP port on the PC. 2. Connect an audio output device such as headphones or port on the product.
Initial Setup Before Using the Monitor Connect external equipments properly. Insert the power plug, and switch ON the main power switch on the back. Power On/Off • Touch the on the front of the monitor. The power indicator light will turn blue when the Monitor is ON. Menu Button Function Adjusting OSD menu settings by controlling menu buttons on the front of the monitor. Enter the main menu; Confirm the selection.
OSD Menu Settings SOURCE Touch the to enter SOURCE mode, then touch the again to enter and use the / to select among different input signals. Touch the to display the On Screen Display menu. Touch the again to enter the input source list. Touch the / to confirm. Touch the VGA Maximum resolution: 2048x1152 @60Hz (Analog Signal) DVI Maximum resolution: 3840x2160 @30Hz (Digital Signal) HDMI 1 HDMI 2 DisplayPort 1 DisplayPort 2 to select your desired input source and touch the to exit.
OSD Menu Settings LANGUAGE To allow users to choose from available languages. to display the On Screen Display menu. Touch the Touch the / Touch the Touch the confirm. Touch the to select LANGUAGE. again to enter the language setting. / to select your desired setting and touch the to to exit.
OSD Menu Settings PICTURE Manually adjust the Brightness, Contrast, Sharpness, Picture Format, Over Driver and ECO Mode of screen image. AUDIO PiP/PbP COLOR PICTURE SOURCE Brightness 50 Contrast 50 Sharpness 50 Picture Format 16:9 OVD Off DCR Off to display the On Screen Display menu. Touch the Touch the Touch the / to select PICTURE. again to enter the picture setting. Touch the / to select your desired setting and touch the enter. Then use the / to adjust the setting.
OSD Menu Settings COLOR To select the color to adjust Color Temperature and User Define. to display the On Screen Display menu. Touch the Touch the / Touch the to select COLOR. again to enter the color setting. Touch the / to select your desired setting and touch the enter. Then use the / to adjust the setting. Touch the Color Temperature User Define to to exit. Cycle among color temperatures: 12000K, 9300K or 6500K. Individual adjustments for red(R), green(G), blue(B).
OSD Menu Settings PIP/PBP PiP/PBP allows you to watch two screens from different sources at the same time. (PiP is picture in picture; PBP is picture by picture) Touch the Touch the Touch the to display the On Screen Display menu. / to select PiP/PBP. again to enter the PiP/PBP setting. Touch the / to select your desired setting and touch the enter. Then use the / to adjust the setting. Touch the PiP/PBP Mode Sub Win1 Input Sub Win2 Input Sub Win3 Input PiP Size PiP Position Swap to to exit.
OSD Menu Settings AUDIO To adjust the audio functions. to display the On Screen Display menu. Touch the Touch the Touch the / to select AUDIO. again to enter the audio setting. Touch the / to select your desired setting and touch the enter. Then use the / to adjust the setting. Touch the Volume Mute Audio Source to to exit. To adjust the volume of speaker output. To turn the Mute ON/OFF. • When in HDMI 1 or HDMI 2 input, select where the audio source comes from Line-in, HDMI 1 or HDMI 2.
OSD Menu Settings SETUP To set up H. Position, V. Position, Phase, Clock, Auto, DisplayPort, Reset and Information. SOURCE LANGUAGE OSD SETUP H. Position 50 V. Position 50 Phase 50 Clock 50 to display the On Screen Display menu. Touch the Touch the Touch the / to select SETUP. again to enter the setup setting. SETUP Auto AUDIO PiP/PbP DisplayPort 1.2 Reset No Touch / to select your desired setting and touch the enter. Then use the / to adjust the setting.
OSD Menu Settings OSD SETUP To manually adjust the Horizontal/Vertical OSD position, Transparency and OSD Time Out. to display the On Screen Display menu. Touch the Touch the Touch the / to select OSD SETUP. again to enter the OSD setting. Touch the / to select your desired setting and touch the enter. Then use the / to adjust the setting. Touch the Horizontal Vertical Transparency OSD Time Out to to exit. To horizontally adjust the OSD position. To vertically adjust the OSD position.
Specifications General Model Name Size 39.5 Inches (100 cm) Display area 878.11 mm (H) x 485.35 mm (V) 34.57 Inches (H) x 19.10 Inches (V) Pixel Pitch 0.076225 mm (H) x 0.22417 mm (V) 0.003 Inches (H) x 0.0088 Inches (V) Panel Brightness Power Supply Dimensions (W x H x D) / Weight Environmental considerations SM40UNP 350 Cd/M² AC 100 - 240 V ~, 50/60 Hz Without Stand 911 x 60 x 529 mm / 11.5 kg 35.86 x 2.36 x 20.82 inches / 25.4 lbs With Stand 911 x 280 x 617 mm / 15 kg 35.86 x 11.02 x 24.
Specifications PowerSaver The power-saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time. The power is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or move the mouse. Power-saving mode functions only when the product is connected to a PC that has a power-saving function.
Specifications Standard Signal Mode Table • This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Therefore, a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for the screen size of your product. • Check the frequency when you exchange a CDT monitor (connected to a PC) for an LED monitor.
Specifications HDMI / DisplayPort Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 31.469 59.940 25.175 -/- MAC, 640 x 480 35.000 66.667 30.240 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.000 +/+ VESA, 800 x 600 46.875 75.000 49.
Service Hotline: 1-855-MY-SEIKI (1-855-697-3454) SEIKI.com © 2014 Seiki, LLC All rights reserved.
