EPSON / WLU3072-D69(RoHS) 2.4GHz Wireless LAN MINI USB module WLU3072-D69(RoHS) Installation Operation Install 1. Executer “DNGL_REL_4_110_39_8_WIN_MFG_TEST.
2. Execute “BRCM_802.11_Mfgtest_1_0_0_33.
3. At DOS command mode, at folder “C:\BRCM_802.11_Mfgtest_1_0_0_33”, type “install tester”. It automatic goes to folder “C:\MFGTEST” Copy the “txg.bat” file to “C:\MFGTEST” folder.
4. Connect WLU3072-D69(RoHS) sample and Windows will search new hard wizard automatic. Install first driver.
5. Install second driver automatic.
Setup TCP/IP 1. Set the Wireless LAN Internet Protocol (TCP/IP) IP: 192.168.1.66 (2~254 as your wish to key in) Mask: 255.255.255.
2.
3.
Instruction 1. txg 54 1 54g (TX) Mode: b/g Channel Data rate (ctrl+c : break continuous transmitter) 2. wl out (RX) 3. wl fqacurcy 1 (FT) Example: 11b, ch1, 1Mbps: txg 1 1 11b 11b, ch7, 11Mbps: txg 11 7 11b 11g, ch1, 54Mbps: txg 54 1 54g 11g, ch11, 6Mbps: txg 6 11 6g Example: ch1: wl fqacurcy 1 ch7: wl fqacurcy 7 ch11: wl fqacurcy 11 Channel 4. wl fqacurcy 0 Close FT mode PS. 1. If the channel doesn’t change well, please execute all instruction then interrupt it. And re-execute again. 2.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
Canadian Regulatory Wireless Notice This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
For NCC 警語 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻 率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立 即停用,並改善至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線 電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之 干擾。 Note: 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤 2.