Specifications

78
79
※ Thefigureaboveisoneexample.Performanceofyourwatchisdifferentfromabovesample.
Performance and type
The case back shows the caliber and performance of your watch
Daily care
● The watch requires good daily care
・Wipeawaymoisture,sweatordirtwithasoftcloth
・Tocleantheclearances(aroundthemetallicband,crownorcaseback),asoft
toothbrushisconvenient.
・Aftersoakingthewatchinseawater,besuretowashthewatchincleanpure
waterandwipeitdrycarefully.
● Turn the crown from time to time
・Inordertopreventcorrosionofthecrown,turnthecrownfromtimetotime.
・Thesamepracticeshouldbeappliedtoascrewlocktypecrown.
(Noneedtopulloutthescrewlocktypecrown.)
Screwlocktypecrown→page63
Waterresistant
performance
Magnetic
resistant
performance
Refertopages80and81.
Calibernumber
Thenumbertoidentify
thetypeofyourwatch
80
81
Magnetic resistance （a󰮏ect of magnetic eld）
A󰮏ected by nearby magnetism, an analogue quartz watch may
temporarily gain or lose time or stop operating.
Diver's watches feature magnetic resistance which is equivalent to JIS Class 1.
Keep the watch more than 5 cm away from magnetic products.
Caution
Examples of common magnetic products that may a󰮏ect watches
Cellular phone
(speaker)
Bag
(with magnet buckle)
AC-powered shaver
Portable radio
(speaker)
Magnetic cooking device etc
Magnetic health belt
Magnetic necklace
Magnetic health mat
Magnetic health pillow
It is because the built-in motor of the watch, which harnesses
magnetic power and external strong magnetism, affect each
other to stop the motor or suppresses the turn of the motor.
The reason why analogue
quartz watch is a󰮏ected
by magnetism.
82
83
Notes on the
length of the band
Notes on skin
irritation and allergy
Skin irritation caused by a band has various reasons such as allergy to metals
or leathers, or skin reactions against friction on dust or the band itself.
Adjust the band to allow a little clearance with your wrist to
ensure proper airow. When wearing the watch, leave enough
room to insert a nger between the band and your wrist.
● Polyurethane band
・ A polyurethane band is susceptible to discoloration from light, and may be
deteriorated by solvent or atmospheric humidity.
・ Especially a translucent, white, or pale colored band easily adsorbs other colors,
resulting in color smears or discoloration.
・ Wash out dirt in water and clean it o󰮏 with a dry cloth.
（Protect the watch body from water splashes by wrapping it up in plastic wrap etc.）
・ When the band becomes less exible or cracked, replace the band with a new one.
Band
The band touches the skin directly and becomes dirty with sweat or dust.
Therefore, lack of care may accelerate deterioration of the band or cause skin irritation
or stain on the sleeve edge. The watch requires a lot of attention for long usage.
● Metallic band
・ Moisture, sweat or soil will cause rust even on a stainless steel band if they are left for a long time.
・ Lack of care may cause a yellowish or gold stain on the lower sleeve edge of shirts.
・ Wipe o󰮏 moisture, sweat or soil with a soft cloth as soon as possible
・ To clean the soil around the joint gaps of the band, wipe it out in water and then
brush it o󰮏 with a soft toothbrush.
（Protect the watch body from water splashes by wrapping it up in plastic wrap etc.）
・ Because some titan bracelets use pins made of stainless steel, which has
outstanding strength, rust may form in the stainless steel parts.
・ If rust advances, pins may poke out or drop out, and the watch case may fall o󰮏
the bracelet, or the clasp may not open.
・ If a pin is poking out, personal injury may result. In such a case, refrain from
using the watch and request repair.
84
85
Close the clasp first （6-1 in
the illustration） and then, the
ap （6-2 in the illustration.）
6
4
Press the lock button.
With the hand which is not wearing
the watch, adjust the length of
the slider so that the watch fits
well around your wrist.
7
Clasp
Lockbutton
7
Limitmark
（uppersurface）
Slider
5
7
Buckle
4
6-1
6-2
5
Lift up the clasp to release the buckle, and strap the watch on
your wrist.
How to use the Diver Adjuster
The Diver Adjuster is a bracelet mechanism to adjust the bracelet length of your Diver'sWatch.
It is very useful when you wear the watch over a wet suit.
Press the ap down further approximately
20°, and hold it there.
2
 Lift up the ap approximately 90°until it stands upright.
1
・ Youmayfeelslightresistance,butdoingthisrequiresonlyalightforce.
 Pleasedonotpushtheapdownforcibly.
Lightly pull the bracelet on the 6 o'clock side of
the watch along the curved line of the bracelet.
3
・Again,doingthisrequiresonlyalightforce.
Pleasedonotpullthebraceletforcibly.
・ Theslidercan be pulled outapproximately30mm.Be
carefulnottopullitoutbeyondthelimitmarkinscribed
onit.（Refertotheillustrationonthenextpage.）
Braceletonthe6o'clock
sideofyourwatch
Braceletonthe12
o'clocksideofyourwatch
Flap
1
2
3