Cal. 9T82 INSTRUCTIONS (P. 3) BEDIENUNGSANLEITUNG (S. 15) INSTRUCTIONS (P. 28) ISTRUZIONI (P. 40) INSTRUCCIONES (P. 53) INSTRUÇÕES (P.
English You are now the proud owner of a SEIKO KINETIC® Cal. 9T82. For best results, please read the instructions in this booklet carefully before using your SEIKO KINETIC®. Please keep this manual handy for ready reference. Sie sind jetzt stolzer Besitzer einer SEIKO KINETIC® Kal. 9T82. Lesen Sie diese Bedienungsanleitung vor der Verwendung Ihrer SEIKO KINETIC® aufmerksam durch, um die optimale Nutzung dieser Uhr zu gewährleisten.
Page HOW TO CHARGE AND START THE WATCH ........................................................ 4 POWER RESERVE IN YOUR SEIKO KINETIC WATCH ............................................ 5 REMARKS ON THE KINETIC E.S.U. ........................................................................ 6 ENERGY DEPLETION FOREWARNING FUNCTION ................................................ 6 HOW TO OPERATE THE SCREW LOCK TYPE CROWN ......................................... 7 TIME/CALENDAR SETTING .............
English HOW TO CHARGE AND START THE WATCH 4 1 Swing the watch from side to side approximately 200 times. 2 Swing the watch approximately 200 times further to reserve one day of power. 3 Set the time/calendar and put on the watch. * Swing rhythmically at a rate of twice a second. * 200 swings will start the watch and the second hand will move at one-second intervals.
POWER RESERVE IN YOUR SEIKO KINETIC WATCH ELECTRICITY STORAGE UNIT (KINETIC E.S.U.). It is a power source completely different from conventional batteries for watches, and therefore, this watch does not require battery replacement. English ● The electric energy generated while the watch is worn on your wrist is stored in the KINETIC ● Power reserve guidelines for the KINETIC E.S.U. You can estimate the power reserve accumulated in the KINETIC E.S.U. from the manner in which you wear the watch.
English REMARKS ON THE KINETIC E.S.U. ● Do not pull the crown out to the second click with the intention of stopping the second hand just to save energy. By doing so, a large amount of current flows through the built-in IC. Therefore, pulling out the crown to the second click will not save energy but, in fact, consume more energy than usual. CAUTION Never install a silver oxide battery for conventional watches in place of the KINETIC E.S.U. The battery may burst, become very hot or catch fire.
HOW TO OPERATE THE SCREW LOCK TYPE CROWN ● To screw in the crown: With the crown at the normal position, turn it clockwise while pressing it. English ● To unscrew the crown: Turn the crown counterclockwise.
English TIME/CALENDAR SETTING Second hand Minute hand Date ➠ ➠ a b 8 a. b. c. d. Screwed-in position Unscrewed position First click Second click ➠ Hour hand c d CROWN Unscrew and pull out to the first click. ▼ Turn counterclockwise until the previous day’s date appears. ▼ Pull out to the second click when the second hand is at the 12 o’clock position. The second hand stops on the spot. ▼ Turn counterclockwise until the desired date appears. ▼ Set the hour and minute hands.
STOPWATCH increments. ● The measured time is indicated by small STOPWATCH hands that move independently of English ● The stopwatch can measure up to 12 hours, 6 minutes and 12.2 seconds in 1/10 second the hands for time indication. TIPS ON READING THE HANDS ● The STOPWATCH minute hand turns a full circle in 30 minutes. The indicated scale, therefore, should be read differently depending on the position of the STOPWATCH hour hand. Ex.
English Ex. ) 1 hour 55 minutes 50 seconds 9 ◆ STOPWATCH second hand reading: The STOPWATCH second hand almost points to “51” but should be read as “50”, as the STOPWATCH 1/10 second hand indicates “9”. STOPWATCH 1/10 second hand 10 ◆ STOPWATCH minute hand reading: The STOPWATCH minute hand almost points to “26” but should be read as “55”, as the measured seconds are “50” and the STOPWATCH hour hand is nearer to the 2-hour marker (refer to the first description in this section).
English STOPWATCH OPERATION ● Before using the stopwatch, be sure to reset the STOPWATCH hands to “0” position. 1) Check that the watch is operating normally. * If the watch has stopped completely or if the second hand is moving at two-second intervals, charge the watch sufficiently. (See “HOW TO CHARGE AND START THE WATCH”) 2) ◆ If the STOPWATCH hands are moving, press button B to stop the measurement and then press button A to reset the STOPWATCH hands to “0” position.
English NOTES FOR USING THE WATCH HOW TO CHARGE AND START THE WATCH ● To charge the KINETIC E.S.U. efficiently, swing the watch from side to side, making an arc of about 20 cm. ● No additional benefit is obtained by swinging the watch more quickly or with greater vigor. ● When the watch is swung, the oscillating weight in the generating system rotates to drive the mechanism. As it rotates, it gives out a sound, which is not a malfunction.
TIME/CALENDAR SETTING English ● Do not set the date between 0:00 a.m. and 2:00 a.m. Otherwise, it may not change properly. If it is necessary to set the date during that time period, first advance the time ahead of 2:00 a.m., set the date and then reset the correct time. ● The date changes instantly when the hands move past the 12 o’clock marker at midnight. When the date is set by turning the hands, however, it may change gradually between 2:00 a.m. and 6:00 a.m. This is not a malfunction.
English ● While the stopwatch is measuring, pressing button A will not reset the stopwatch. ● Do not press buttons A and B at the same time, nor press one of the two buttons while keeping the other pressed. Otherwise, a malfunction will result. SPECIFICATIONS 1 2 3 4 5 6 7 8 9 Frequency of crystal oscillator .......................... 32,768 Hz (Hz = Hertz … Cycles per second) Loss/gain (monthly rate) ....................................
