DIGITALMASTER L-758DR L-758D L-758 Operating Manual
Blank page
Safety Precautions use it properly. WARNING Indicates hazard or unsafe use that can result in personal injury or death. CAUTION Indicates hazard or unsafe use that can result in personal injury or damage to your light meter. NOTE: Indicates a caution or limitation that accompanies operation. Please read the note to avoid incorrect operation. Reference: Provides the reference information and related functions that are useful in operating. We recommend that you read these references.
Table of Contents Safety Precautions Table of Contents 1. Parts Designation ............................................................................................... 1 1. Light Meter Parts .............................................................................................. 1 2. Supplied Accessories ....................................................................................... 2 2. Explanation of the Liquid Crystal Display(LCD) ............................................. 3 3.
2-3 Cord multiple flash (cumulative) mode ....................................................... 24 2-4 Cordless multiple flash (cumulative) mode ................................................. 25 2-5 Flash analyzing function ............................................................................. 27 2-6 Wireless Flash Radio Triggering ................................................................. 28 6. Advanced Functions ...........................................................................
Table of Contents 10.Care and Maintenance ...................................................................................... 56 FCC & IC compliance information ........................................................................
1. Parts Designation ① Lumisphere retracting ring Light Meter Parts ENGLISH 1.
1. Parts Designation 2.
2. Explanation of the Liquid Crystal Display (LCD) ENGLISH LCD for L-758DR/L-758D LCD for L-758CINE NOTE: For explanation purposes, the display illustrated here shows all icons and readouts simultaneously. Actual LCD screen will not show all icon as above during normal use. Auto Electro-Luminescent Display (EL) • In low light (EV 6 or less), a green backlight will automatically illuminate the entire LCD.
2.
⑦ Analog Scale Displays measured values as icons along the apertures or Latitude EV scale. The scale is graduated in full or 1/3 stop increments for measurements. Memorized and averaged values are also display along the scale. • Aperture scale (upper scale) displays in all mode except Aperture priority mode. f 0.7 to f 90 in full stops appears in all modes except aperture priority mode (L-758) • f 0.
2.
3. Before Using 1. Attach the strap Attach the Strap @7 by passing the small loop end through the eyelet ⑨ and passing the other end of strap through it. OD MO WARNING • To avoid a danger of strangulation, please keep the strap in a location where an infant cannot reach it and accidentally get the strap wrapped around his or her neck. 2. Inserting the battery 1. Requires one 3.0 v CR123A lithium battery (included). 2.
3. Before Using 4. Replacing the battery during measurement or when using the memory function 1. Always turn the power OFF before replacing the battery. If the battery is removed with the power ON, measurements and settings in memory can no longer be recalled. 2.
3. Before Using 8. Jog Wheel Lock or Lock Off 1. Hold down the Mode button ⑩ and ISO1 button ⑪ and “LOC” will appear to indicate that the Jog Wheel is locked. The last measurement is held until the lock is released, even if the Jog wheel ⑤ is accidentally moved. However, if the measurement button ⑭ is pressed, a new measurement is displayed with the same locked settings. 2.
3. Before Using 9. Setting the Measuring and Memory button configuration In the custom settings mode (refer to P40), the Measuring button and the Memory button can be set as follows. 1. For Incident measuring The Measuring button and Memory button is set in the standard configuration. (Described on Page 1 in Light Meter Parts) Please make sure that the default value in the Custom settings mode is set to .(Custom No.17, Item No. 0) Memory Measuring button button Configuration 1) 2.
4. Basic Operation 1. Incident or reflected spot measuring 1. To set for either incident or reflected light operation, turn the Incident / Reflected Spot Selector Dial ⑲ on the eye piece, to the desired position ( or mark) until it clicks. Incident operation 2. Reflected Spot operation When incident operation is selected, the mark will blink for ten seconds and when Reflected mark will blink for ten seconds on the LCD.
4. Basic Operation 2. Setting measuring mode 1. Hold down the Mode button ⑩ and turn the Jog wheel ⑤ to select the desired mode.
4. Basic Operation 3. Incident Measurement Mode Incident light measuring is the measurement method that employs either the Lumisphere or Lumidisc functions. Measurements should be with the Lumisphere aimed towards the camera direction from the subject position. 1. You can select extended or retracted lumisphere measuring positions by rotating the Lumisphere retracting ring ① (clockwise or counter-clockwise) until it clicks into position. Extended Lumisphere Retracted Lumisphere (Lumidisc) 2.
4. Basic Operation 4. Reflected Measurement Mode (spot metering) This method measures the brightness (luminance) of the light reflected from the subject. It is useful for distant objects such as landscapes, when you cannot go to the position of the subject, or for metering subjects that generate light (neon signs, etc.), highly reflective surfaces or translucent subjects (stained glass, etc.). 1. Take the measurement by aligning the circle inside the viewfinder with the subject area to be measured. 2.
5. Measurement 1. Measuring ambient light In this measurement mode, we have the choice of shutter priority mode, aperture priority mode or EV mode. Hold down the Mode button ⑩ and turn the Jog wheel ⑤ to select ambient measurement . mode 1-1 Shutter Speed Priority mode 1. Hold down the Mode button ⑩ and turn the Jog wheel ⑤ to select Shutter Speed Priority mode . 2. Turn the Jog wheel to set the desired shutter speed. 3. Press the Measuring button ⑭ to take a measurement.
5. Measurement • “E.u” (Exposure under) or “E.o” (Exposure over) appears when the combination of shutter speed and aperture is outside the display range. ☆ When E.O (Exposure Over) is displayed,it indicates that the measured exposure is outside the display range, changing the shutter speed to a faster setting with the Jog wheel will allow you to find a combination of proper aperture and shutter speed. ☆ When E.
5. Measurement 1-2 Aperture Priority mode 1. Hold down the Mode button ⑩ and turn the Jog wheel to select aperture priority mode . 2. Turn the Jog wheel ⑤ to set the desired f stop value. 3. Press the Measuring button ⑭ to take a measurement. Release the Measuring button to complete the measurement. The measured value (shutter speed) at the time will be displayed. Measured value (shutter speed) Set f stop value While pressing the Measuring button, the meter measures continuously until it is released.
5. Measurement 1-3 EV mode 1. To activate EV mode, please set Custom setting no.5 and Item no.1. (See page 40) 2. Hold down the Mode button ⑩ and turn the Jog . wheel ⑤ to select EV mode 3. Press the Measuring button ⑭ to take a measurement. Release the Measuring button to complete the measurement. The measured value (EV=Exposure Value) at that time will be displayed.
5. Measurement 1-4 Cinematography 1. Hold down the Mode button ⑩ and turn the Jog wheel ⑤ to select ambient light shutter speed priority mode . 2. Turn the Jog wheel to select the Cine Speed for the camera that will be used. Cine Speed are displayed after 1/8000, 1/200, 1/400 and the unit is in frames per second (f/s). [L-758DR/758D] The following Cine Speeds will be displayed: 2, 3, 4, 6, 8, 12, 16, 18, 24, 25, 30, 32, 36, 40, 48, 50, 60, 64, 72, 96, 120, 128, 150, 200, 240, 256, 300 and 360 f/s.
5. Measurement 4. Setting the shutter angle (L-758CINE only). It is possible to set the shutter angle by turning the Jog wheel ⑤ while pressing Mode button ⑩ and ISO2 button ⑥ . Note: • Shutter angle: The angle can be set in the range of 1°to 10° (in 1° steps), 15° - 270° (in 5° steps) as well as, 12°, 17°, 22°, 144° and 172°. • " " is displayed continuously on the LCD display if the shutter angle is set to any value other than 180°.
5. Measurement 2. Measuring electronic flash This method of measurement can be done in the following modes; with cord, without cord, and Wireless flash radio triggering mode (cumulative or non-cumulative). When Measuring flash light, the shutter speed and F stop value (value combining ambient light and flash light: total amount of light) are displayed. The ambient light and flash light are each displayed as separate values together with the total amount of light on the analog scale.
5. Measurement WARNING: • To avoid a danger of choking, please place Synchro terminal cap in a location where an infant cannot reach and accidentally swallow it. CAUTION: • There is danger of electric shock if the meter is handled with wet hands, during rain, in areas splashed by water or where there is a lot of moisture. Under such conditions, it is recommended that you use the meter in the cordless flash mode or Wireless flash radio triggering mode, and keep the Synchro terminal cap in place.
5. Measurement 3. When the Measuring button ⑭ is pressed, the will blink and the meter is ready to mode mark measure. The ready to measure mode will continue for approximately 90 seconds. During this time, trigger the flash to make a measurement. 4. If the 90 second period is exceeded and the blinking mark stops, press the Measuring button again to return to ready to measure status.
5. Measurement 2-3 Cord multiple flash (cumulative) mode These measurements are used when the light generated by the flash is inadequate for proper exposure. The repeated flash pops can be accumulated until the desired aperture is displayed. The cumulative number is infinite. Only one digit is displayed if the cumulative number is ten or more. Display returns 0 (0=10, 1=11, 2=12, etc.) To activate Multiple cumulative mode, please set custom setting no.6 and Item no.1. 1.
5. Measurement CAUTION: • There is danger of electric shock if the meter is handled with wet hands, during rain, in areas splashed by water or where there is a lot of moisture. Under such conditions, it is recommended that you use the meter in the cordless flash mode, or wireless flash radio triggering mode and keep the Synchro terminal cap in place. NOTE: • The flash unit may flash when you connect the Synchro cord or operate the Power button.
5. Measurement 2. When the light from the flash is received, the measured value (f stop) is displayed. Each time this is repeated, the accumulated value for the aperture and the number of cumulative flashes is displayed. Percentage of flash in total exposure Measured f stop Number of cumulative flashes 1/10 f stop Set shutter speed 1st. time 2nd. time Measured f stop (total exposure) 3rd. time 3. The ready to measure mode will be displayed for approximately 90 seconds.
5. Measurement 2-5 Flash analyzing function When measuring flash light, the shutter speed and F stop value (combining ambient light and flash light: total amount of light) are displayed on the LCD screen and the ambient light and flash light are each displayed as separate values along with the total amount of light (combined flash and ambinent) on the analog scale. In addition, the ratio of flash light to the total amount of light is displayed as a percentage (in 10% steps) at the sametime.
5. Measurement 2-6 Wireless Flash Radio Triggering With the Radio Transmitter module plugged into the meters radio socket and a Receiver or Transceiver (PocketWizard®) connected to one or more electronic flash units, the meter provides a convenient system that enables one person working alone to measure flash output without the need of a sync cord. Pressing the Measuring button simultaneously triggers the flash and measures the flash output simultaneously.
5. Measurement 4. In the Quad-Triggering zone setting, after the channel is set to 17 to 32, the assigned buttons below are pressed. Pressing each of the buttons activates or deactivates the QuadTriggering zone (A, b, c or d). When a Quad-Triggering zone is activated, the corresponding Quad-Triggering zone letter appears on the display. If a Quad-Triggering zone is deactivated, a “-" is displayed in its place. ↔ Each assigned button enables to set Quad-triggering zone directly. ISO 1 ISO 2 MID.TONE M.
5. Measurement Reference: • Refer to the radio Receiver or Transceiver instruction manual for the recommended operating method. • Maximum distance of the radio flash triggering system can vary depending on the placement of the remote Receiver or Transceiver, direction of the radios antenna, distance from a large body of water or concrete wall and other possible factors. 1. 2. 3. 4. Confirm the range between the meter (transmitter) and Receiver or Transceiver.
6. Advanced Functions 1. Memory function This meter can store up to nine measured values in memory for incident light and reflected light simultaneously. This feature can be used in the following modes; Ambient light : shutter speed priority, aperture priority or EV mode. Electronic Flash light : cord, cordless or wireless flash radio triggering mode. 1. Press the Measuring button ⑭ and take a measurement. The Current measured value on the analog scale will blink. 2.
6. Advanced Functions 2. Averaging function This function displays the average of up to nine of the values in memory. 1. Press the Measuring button ⑭ and take a measurement. Current measured value on the analog scale will blink. 2. Press the Memory button ⑦ and store the measured value in memory, and memorized value on the analog scale stops blinking. 3. Memory button When the AVE./ ∆ EV button ④ is pressed, an averaged value for up to nine measurements will be displayed on the LCD.
6. Advanced Functions 2. Turn any secondary light source off. Point the Lumisphere toward the main light source, from the position of the subject and take a measurement. Press the Memory button ⑦ and store the value in memory. 3. Press the AVE./ ∆ EV button ④ and display the “A”mark on the LCD indicating a standard value. Memory button Indicator of reading Set shutter speed 4. Turn the main lighting off. Now, point the Lumisphere toward the secondary light source.
6. Advanced Functions 4. How to use an incident illuminance (LUX or FC) meter (L-758DR/758D) 1. Turn the Lumisphere retracting ring ① to lower it to the (retracted) mark position. 2. Make sure that any compensation Exposure/Calibration compensation: see page 36 & 37, Compensation of camera exposure profile: see page 46 is canceled. 3. Set the meter to EV mode and ISO 100. 4. Place the meter parallel to the subject and take a measurement. 5.
6. Advanced Functions 5. How to use a reflected luminance (cd/m2 or FL) meter (L-758DR/758D) 1. Exposure/Calibration compensation: see page 36 & 37, Compensation of camera exposure profile: see page 46. 2. Set the meter to EV mode and ISO 100. 3. Set meter to spot reading for reflected light. Take the measurement by looking through the finder and aligning so the subject that will be measured is inside the circle. 4.
6. Advanced Functions 6. How to use the Exposure compensation function Exposure compensation can be made in precise 1/10 step increments in a +/- 9.9 EV range. Exposure compensation may be necessary when compensation for filters, bellows, extension tube, etc is required. 1. Set the measurement mode (incident light, reflected light) for the desired compensation. You can make calibration compensation independently for both incident, and reflected light.
6. Advanced Functions 7. How to use Calibration compensation function Calibration compensation can be made in precise 1/10 step increments in a +/- 1.0 EV. It provides the ability to match exposure measurements with meters to meters, correct exposure for special requirements, adjusts for film or digital cameras,etc. 1. Set the measurement mode (incident light, reflected light) for the desired compensation. You can make calibration compensation independently for both incident, and reflected light.
6. Advanced Functions 8. Filter compensation 8-1 Filter compensation (1) It is possible to compensate for filter factor within a range of ±5.0 EV in 1/10 steps. The measurement corresponding to the set compensation and can be displayed while pressing ISO2 button ⑥ . Highlight and shadow compensation values can also be enter for quick exposure metering. 1. Select setting number 1 and item number 1 in the custom setting mode (see page 40). 2.
6. Advanced Functions 8-2 Filter factor number compensation (2) (L-758CINE only) When using the L-758DR for Cine/Video exposures, in cine industry, it is possible to set 7 different frequently used types of filters. 1. Select setting number 1 and item number 2 in the custom setting mode (see page 40). 2. The symbol of the desired filter from among the 7 types can be selected by turning the Jog wheel ⑤ while pressing ISO2 button ⑥ . 3.
6. Advanced Functions 9. Custom setting function The following Custom Settings provide a quick and easy setup of individual meter preferences. All preferences are stored on a memory chip and can not be deleted, they can only be changed back to default settings. *1 *2 1/10 stop fractions are displayed in full, 1/2 and 1/3 step increments.
6. Advanced Functions 1. To enter the custom setting mode, the meter must first be turned off. Press Mode button ⑩ and turn the power on. 2. In the custom setting mode, ‘CS’ (custom setting) is displayed in the ISO display area, a setting number between 01-14 (L-758DR/758D) or 01-17 (L758CINE) is displayed in the shutter speed display area and item number 0, 1, 2 or 3 is displayed in the aperture display area. Custom setting item no. Custom setting no. 3.
7. Camera Exposure Profiling 1. -42- Calibration testing for exposure profiling Since no two digital cameras, camera and light meter or different types of film are likely to agree on the same exposure, they need to be calibrated. The L-758DR (L-758D/L-758CINE) can be programmed to match the sensitivity of film or digital camera sensor for prefect exposure control.
It is necessary to test the cameras sensitivity, measure the actual dynamic range and know the clipping points of your digital camera and/or type of film and processing used before programming the L-758DR (L-758D/L-758CINE) meter for Exposure Profiling. Film exposures should be evaluated by scanning the film first and then evaluating the images in a photo application software. The use of a transmission/reflective densitometer can also be used if film scanning is not possible or desired.
7. Camera Exposure Profiling 2. Input test target data There are two ways to input the result of the test target data into the light meter: 1) Sekonic Data Transfer Software - install application software from the included CD-ROM and connect the computer and light meter via USB, and 2) Direct Input - Manually enter the test target data directly into the light meter. 2-1 Sekonic Application Software Data Transfer Software is included with the L-758DR, L-758D and L-758CINE.
2-2 Manual Exposure Profile Input It situations where it is not possible or convenient to use a computer or the Sekonic Data Transfer Software, Exposure Profile data can be entered into the L-758DR (L-758D or L-758CINE) directly. Below is the step by step process for manually entering a specific Exposure Profile. 1) With the meter turned off,enter the Camera Exposure Profile mode by pressing the Power button ⑫ while pressing the AVE../ ⊿ EV button ④ at the same time..
7. Camera Exposure Profiling 7) Setting compensation value Rotate the Jog wheel ⑤ while holding down ISO1 button ⑪ and ISO2 button ⑥ simultaneously. Compensation values can be made in 1/10 step increments in +/-5.0EV. 8) Setting Clipping point (-) Rotate the Jog wheel ⑤ while pressing AVE./ ⊿ EV button ④. Clipping point can be set from -7 to 0EV in 1/10 step increments. 9) Setting Dynamic range (-) Rotate the Jog wheel ⑤ while pressing MID.TONE button ⑳ .
7. Camera Exposure Profiling ENGLISH 11) Setting Clipping point (+) Rotate the Jog wheel ⑤ while pressing ISO2 button ⑥ . Clipping point can be set from 0 to +7EV in 1/10 step increments. 12) Press the Measuring button ⑭ if you want to copy this ISO setting to all ISO setting (from ISO 3 to 8000) Reference: • To return to a previous setting, press the ISO1 button ⑪ and the Memory clear button @3 simultaneously.
7. Camera Exposure Profiling 3. How to use Exposure Profiling mode 3-1 Selecting Camera Exposure Profiling Preset Camera Exposure Profiles (Camera 1, 2 and 3) can be recalled. 1) Press and hold down the ISO 1 button ⑪ ,while pressing the MID.TONE button ⑳ to select the desired Camera profile (Camera 1, 2 or 3). NOTE: • Holding down the MID.TONE button first and pressing ISO1 button makes the last measurement value “Mid.Tone” as standard value. Be sure to hold the ISO1 button first and press the MID.
2) The EV scale displays Clipping points(+/-),Dynamic range(+/-)and Mid. Tone with a triangle " "icon. 3) Measured value exceeding Dynamic range will be displayed as a slow blinking " " icons.Measurements that exceed the clipping points will be displayed as fast blinking " " icons. Clipping point(-) Clipping point(+) Dynamic range(-) Dynamic range(+) Mid.Tone Exceed clipping Exceed dynamic point (blinking faster) range(blinking slowly) Mid.
7. Camera Exposure Profiling 2) After setting the Mid.Tone (ex.Incident reading), take measurements (highlight or shadow, etc. with spot reading) and memorize them to see if measurements are within Dynamic range or Clipping points. Mid. Tone F5.65 Measure and memorize the Highlight F160 Measure and memorize the Shadow F2.03 3) Adjusting Mid.Tone Value If it becomes necessary to change the measured mid-tone value, press and hold down the MODE button while pressing the MID.
4) Setting Mid.Tone Value from Memorized Values After taking three or more reflected Spot measurements, select which memorized value on the analog scale should be the Mid-Tone value. First enter the memory recall mode by pressing and holding the MODE button, while pressing the Memory button. Select one of the memorized values by rotating the Jog wheel and press the MID.TONE button to set it as the Mid-tone value. Memory button Memory recall mode Select desired memorized value as Mid.Tone Press MID.
8. Optional Accessories Synchro cord • This is a five-meter long cord with three plugs. An exposure meter, a camera, and a flash can all be connected at the same time. This is convenient when measurements are made, because it is not necessary to plug and unplug the synchro cord. 18% Gray Card • 18% gray card with cover (110mm x 102mm, 4 1/4” x 3 1/ 2”), folds to 2 3/4” x 4 3/4”, and fits in a shirt pocket. • It provides accurate exposures regardless of reflected ratio of the subject and surroundings.
8. Optional Accessories Wireless Flash Radio Triggering module (For the L-758D or L-758CINE. ) • Electronic flash units and/or cameras can de triggered wireless from the L-758 or L-758CINE with optional radio module using PocktWizard Receiver or Trans ceivers connected to them. Radio transmitter module (32 channels) RT-32FCC (for US or Canada) RT-32CE (for EU countries) Radio frequency FCC & IC (indicating “Use RT-32FCC for radio transmitter module” on the back of body) CH1 ~ 16 : 344.
9.
9. Technical Data Aperture EV Analog scale : f/0.5 to f/161.2 (in 1, 1/2 or 1/3 steps) : EV -9.9 to EV 46.6 (in 1/10 steps) : F-scale F0.7 – F90 (in 1/3 steps), (for 758DR/758D) F0.5 – F64 (in 1/3 steps), (for 758CINE) EV scale -7.0EV to +7.0EV (in 1/3 steps) Contrast function : +/- 9.9 EV (in 1/10 steps) Shutter angle (758CINE only) : 1° ~ 10° (in 1°steps),15° ~ 270° (in 5°steps), plus12°,17°, 22°,144°,172° Filter compensation : +/- 5.
10. Care and Maintainance NOTE: • Although this meter has an All-weather design for everyday use (JIS standard water resistance class 4), do not place it in water or use it underwater. This will cause it to malfunction. Splashed Rain Do not wash with water Do not submerge or use under water • To avoid damaging this meter, never drop it or subject it to shock. • Avoid storing it in places with high temperatures or humidity.
FCC & IC compliance information Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant To Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
-58-
Memo -59-
Memo -60-
Blank page
7-24-14, OIZUMI-GAKUEN-CHO, NERIMA-KU, TOKYO 178-8686 JAPAN TEL:+81(0) 3-3978-2335 FAX:+81(0)3-3978-5229 http://www.sekonic.co.
