SUPERPLUS WATER FILTRATION SYSTEM For Model #: SP20-2, SP40-2 INSTRUCTIONS/ASSEMBLY USE AND CARE MANUAL (Important: Read this manual thoroughly before install)
TABLE OF CONTENTS 2 General Notes 3 About Your Product 4 Installation Procedures for Hard Copper Pipe 6 Installation Procedures for Rigid Plastic Pipe 8 Directions to Reverse Water Flow 9 Cartridge Change-Out Instructions 10 QR Code Instructions 11 Troubleshooting & Repair 12 Limited Warranty HELP AND SUPPORT Selecto, Inc. 3980 Lakefield Court Suwanee, GA 30024 USA WWW.SELECTOINC.COM Product Customer Support Hotline: Toll Free: 1-800-635-4017 Customer-Service@SelectoInc.
THANK YOU FOR PURCHASING OUR PRODUCT Everyone here at Selecto, Inc. would like to thank you for your support and continued use of our products. We believe everyone should have access to safe, clean water. Your purchase is a small step towards a clean future. GENERAL NOTES It is important to ensure that you are in compliance with all applicable state and local plumbing codes before you start installation of this product. Use of a licensed technician for installation is recommended.
ABOUT YOUR PRODUCT SP20-2 SP40-2 • 400,000 gallon capacity at 15 GPM • Temperature range between 34° F and 100° F • Minimum pressure: 40 PSI • Maximum pressure: 120 PSI • 300,000 gallon capacity at 10 GPM • Temperature range between 34° F and 100° F • Minimum pressure: 40 PSI • Maximum pressure: 120 PSI Dimensions: 22” × 9” × 29” Dimensions: 22” × 9” × 23” Weight: With Water: 54 lbs. Without Water: 28 lbs. Weight: With Water: 40 lbs. Without Water: 21 lbs.
INSTALLATION PROCEDURES For Hard Copper Pipe Installing (steps 1 to 6 of 11): INSTALL FILTER HEAD: Tap Water Inlet A. Filter Head Assembly Filtered Water Outlet B. You can slide the heads out toward either side of channel to separate backplate for easy installation 1. Center, level, and mount the filter heads 2. Remove blue clip from inlet side 3. Pull and separate inlet Shut-Off valve fitting 4. Connect inlet fitting onto 3/4” hard piping 5.
INSTALLATION PROCEDURES (CONTINUED) For Hard Copper Pipe Installing (steps 7 to 11 of 11): 7. Hand press down the clip and flush w/head surface Tap Water Inlet Filtered Water Outlet 8. Repeat steps 2-7 for the outlet side of piping 9. Install 1st cartridge w/ align 4-tags 10. Install the 2nd cartridge 11. Now the installation is complete © Selecto, Inc.
INSTALLATION PROCEDURES (CONTINUED) For Rigid Plastic Pipe Installing (steps 1 to 6 of 14): INSTALL FILTER HEAD: Tap Water Inlet A. Filter Head Assembly Filtered Water Outlet B. You can slide the heads out toward either side of channel to separate backplate for easy installation 1. Center, level, and mount the filter heads 2. Remove blue clip from inlet side 3. Pull and separate inlet Shut-Off valve fitting 4. Connect inlet fitting onto 3/4” hard piping 5.
INSTALLATION PROCEDURES (CONTINUED) For Rigid Plastic Pipe Installing (steps 7 to 14 of 14): 7. Hand press down the clip and flush w/head surface 8. Repeat steps 2-7 for the outlet side of piping 9. Apply sealant on 3/4” CPVC pipe 10. Reconnect plastic fitting/clip back to the filter head 11. Installed Plastic pipe Tap Water Inlet 12. Install 1st cartridge w/align 4-tags © Selecto, Inc. 13. Install 2nd cartridge Filtered Water Outlet 14.
DIRECTIONS TO REVERSE WATER FLOW NOTE: Not recommended, unless necessary EXCHANGE PROCEDURES See below diagram. Begin by pulling out the blue clips on either side. Proceed to remove the 4 fittings (two from each end) and exchange with the opposite end. Properly install all fittings back on the filter head. If using hard copper piping, use the same technique from pages 4 and 5 (ref. Steps 2-7). If using rigid plastic piping, use the same technique from pages 6 and 7 (ref. Steps 2-7).
CARTRIDGE CHANGE-OUT INSTRUCTIONS Cartridges should be changed at least once a year, when the pressure on the gauge has dropped into the red zone (less than 20 psi), or when bad taste and/or odor return. 1. Shut off inlet valve 2. Push “Red” pressure relief button to relieve pressure Normally located at left end of the filter system. Push until no more water comes out. 3.
QR CODE INSTRUCTIONS It is recommended to replace cartridges at least once a year, or when the pressure on the gauge has dropped into the red zone (less than 20 psi), or when bad taste and/or odor return. Use the QR code to register and receive an email alert when it’s time to change the filtration cartridges to maximize filter performance. Get email alerts! 1. Scan the QR code on filter cartridge label with your smart phone. 2.
TROUBLESHOOTING AND REPAIR All SuperPlus Filtration Systems are fully inspected and pressure tested by factory. IF LEAKS- Note: The inlet shut-off valve must be turned “OFF” (handle in vertical position), and pressure relieved by pushing the “Red” pressure relief button before attempting to fix any leakage problems. 1. Leaks at threaded connection points. This type of leak should be repaired by removing the fitting and applying additional Teflon tape or thread sealant compound.
SELECTO SUPERPLUS WHOLE HOUSE FILTRATION SYSTEM LIMITED WARRANTY For Products: SP20-2, SP40-2 What is Covered: SELECTO warrants the heads of the Selecto SuperPlus Whole House Filtration System to be free of defects in material and workmanship. Filtration cartridges are excluded from the warranty. For how long: The Plastic Head on the Product carry a five (5) year limited warranty.
SELECTO SUPERPLUS WHOLE HOUSE FILTRATION SYSTEM LIMITED WARRANTY (CONTINUED) For Products: SP20-2, SP40-2 When you receive your product: All claims, whether concealed or not, are your responsibility. Any carton damage or shortages should be noted on the bill of lading at the time of receipt of the shipment, in accordance with I.C.C. Regulations. If the concealed damage or loss is noted while unpacking the shipment, the carrier should be notified immediately, per I.C.C. Regulations.
