| SMH3 SMH3 Motorcycle Bluetooth Headset & Intercom SENA www.senabluetooth.
| SMH3 © 1998-2013 Sena Technologies, Inc. All rights reserved. Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior notice. Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license. Other trademarks and tradenames are those of their respective owners.
| SMH3 CONTENTS 1. INTRODUCTION 2. PACKAGE CONTENTS 3. INSTALLING THE SMH3 ON YOUR HELMET 4. POWERING ON/OFF AND CHARGING 4.1 Powering On 4.2 Powering Off 4.3 Charging 4.4 Low Battery Warning 5. CHECKING THE BATTERY LEVEL 5.1 LED Indicator 5.2 Voice Prompt Indicator 6. PAIRING THE SMH3 WITH BLUETOOTH DEVICES 6.1 Mobile Phone Pairing 6.2 Multipoint Mobile Phones Pairing 6.3 Bluetooth Stereo Device Pairing 6.4 Bluetooth GPS Navigation Pairing 7. PAIRING WITH OTHER SMH3 HEADSETS FOR INTERCOM CONVERSATION 8.
| SMH3 10.
| SMH3 1. INTRODUCTION Thank you for choosing the Sena SMH3, Motorcycle Bluetooth Headset and Intercom. With the SMH3, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or voice instructions of GPS navigation by Bluetooth wirelessly, and have intercom conversations in full duplex with a passenger or other riders. The SMH3 is compliant with the Bluetooth Specification 3.
| SMH3 2.
| SMH3 3. INSTALLING THE SMH3 ON YOUR HELMET 2. [picture 3-2] 1. [picture 3-1] Remove the left and right 3. [picture 3-3] side Place the speaker-microphone unit The boom microphone should be cheekpads from the helmet. along with the velcro pad to the left positioned to face properly towards inside surface of the external shell, your mouth. Please make sure that centered to your ear. the microphone is located close to your mouth when you wear the helmet. 4. [picture 3-4] 5. [picture 3-5] 6.
| SMH3 4. POWERING ON/OFF AND CHARGING 4.1 Powering On Press the (+) Button and the (-) Button at the same time for 1 second to power on. The blue LED turns on and you will hear ascending beeps and “Hello”. 4.2 Powering Off Tap the (+) Button and the (-) Button simultaneously. The red LED turns on for about 2 seconds until it turns off completely and you will hear “Goodbye” and descending beeps. 4.
| SMH3 5. CHECKING THE BATTERY LEVEL You can check the battery level in two different ways when the headset is powering on. 5.1 LED Indicator When the headset is powering on, the red LED flashes rapidly indicating the battery level. 4 flashes = High, 70~100% 3 flashes = Medium, 30~70% 2 flashes = Low, 0~30% 5.2 Voice Prompt Indicator When you power on the headset, keep pressing the (+) Button and (-) Button simultaneously for about 3 seconds until you hear three high tone beeps.
| SMH3 6. PAIRING THE SMH3 WITH BLUETOOTH DEVICES 6.1 Mobile Phone Pairing 1. Turn on the SMH3 and press the (+) Button for 5 seconds until the LED flashes red and blue alternately and you hear multiple beeps. You will hear a voice prompt saying “Phone pairing”. 2. Search for Bluetooth devices on your mobile phone. Select the Sena SMH3 in the list of the devices detected on the mobile phone. 3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN. 4.
| SMH3 1. If Bluetooth connection between the headset and a mobile phone is disconnected, press the (+) Button for 3 seconds to recover the Bluetooth connection immediately. 2. If Bluetooth connection between the headset and any other Bluetooth devices is disconnected, tap the (+) Button to recover the Bluetooth connection. 6.4 Bluetooth GPS Navigation Pairing You can listen to voice instruction from Bluetooth GPS navigation.
| SMH3 3. Wait until the LEDs of both headsets turn to blue and intercom connection is automatically established. The two SMH3 headsets A and B are paired with each other for intercom conversation. If the pairing process is not completed within one minute, the SMH3 will return to stand-by mode.
| SMH3 8. SMH3 CONFIGURATION SETTING You can set the configuration of the SMH3 by the voice menu instruction as below. 1. To enter into voice configuration menu, press and hold the (+) Button for 10 seconds until the LED shows solid blue and you hear high tone double beeps. You will hear a voice prompt saying “Configuration menu”. 2. Tap the (+) Button to navigate between menus. You will hear voice prompts for each menu items as below. 3.
| SMH3 Voice Prompt “Voice prompt” Factory Default Enable Enable / Disable Tap the (-) Button You can disable voice prompts by configuration setting, but the following voice prompts are always on. - Voice prompts for configuration setting menu - Voice prompts for battery level Indicator - Voice prompts for factory reset 8.
| SMH3 Execute Tap the (-) Button To exit voice configuration menu and get back to stand-by mode, tap the (+) Button until you hear a voice prompt, “Exit configuration”. Tap the (-) Button to confirm.
| SMH3 9. USING THE SMH3 9.1 Volume Adjustment You can easily adjust the volume by tapping the (+) Button or the (-) Button. You will hear a beep when the volume reaches maximum or minimum level. The volume is set and maintained independently at different levels for each audio source even when you turn off and on the headset. For example, once you set the volume for mobile phone handsfree, it will not change even if you adjust the volume when you hear Bluetooth MP3 music.
| SMH3 2. To terminate an intercom conversation, press the (-) Button for 1 second again. [picture 11-2] 9.4 Intercom and Mobile Phone Call 1. When you have an incoming mobile phone call during an intercom conversation, you will hear a ring tone. You can choose whether to 1) answer the mobile phone call and stop the intercom conversation, or 2) reject the phone call and stay on the intercom conversation. ● To answer the phone call and stop the intercom conversation, tap the (+) Button.
| SMH3 the SMH3 to remotely control music playback. So, You not only can adjust the volume but also use the functions such as play, pause, next track and previous track. ● To adjust the volume, tap the (+) Button or the (-) Button.. [picture 11-3] ● To play or pause music, press and hold the (+) Button for 1 second until you hear a double beep. [picture 11-4] ● To track forward or track back, press and hold the (+) Button or the (-) Button for 2 seconds until you hear a double beep. [picture 11-5] 9.
| SMH3 10. FIRMWARE UPGRADE The SMH3 supports firmware upgrade function. Please visit Sena Bluetooth web site at www.SenaBluetooth.com to check the latest software downloads.
| SMH3 SENA www.senabluetooth.com Users Guide for Firmware v1.
| SMH3 FCC Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
