0S Motorcycle Bluetooth® Communication System
© 1998-2015 Sena Technologies, Inc. All rights reserved. Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior notice. Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries.
CONTENTS 1 INTRODUCTION 2 PACKAGE CONTENTS 3 INSTALLING THE 10S ON YOUR HELMET 3.1 Installing the Main Unit 3.1.1 Using the Clamp Unit 3.1.2 Using the Glued Surface Mounting Adapter 3.2 Installing the Speakers 3.3 Installing the Microphones 3.3.1 Using the Wired Boom Microphone 3.3.2 Using the Wired Microphone 4 GETTING STARTED 4.1 Button Operation 4.2 Powering On and Off 4.3 Charging 4.4 Low Battery Warning 4.5 Checking the Battery Level 4.5.1 LED Indicator 4.5.2 Voice Prompt Indicator 4.
8 INTERCOM 8.1 Two-way Intercom 8.1.1 Starting Two-way Intercom 8.1.2 Ending Two-way Intercom 8.2 Three-way Intercom 8.2.1 Starting Three-way Intercom 8.2.2 Ending Three-way Intercom 8.3 Four-way Intercom 8.3.1 Starting Four-way Intercom 8.3.2 Ending Four-way Intercom 9 THREE-WAY CONFERENCE PHONE CALL WITH INTERCOM PARTICIPANT 10 GROUP INTERCOM 11 UNIVERSAL INTERCOM 11.1 Universal Intercom Pairing 11.2 Two-way Universal Intercom 11.3 Three-way Universal Intercom 11.4 Four-way Universal Intercom 11.4.
15.2 Using the Handlebar Remote 16 FIRMWARE UPGRADE 17 TROUBLESHOOTING 17.1 Intercom Failure 17.2 Intercom Reconnection 17.3 Fault Reset 17.
1 INTRODUCTION Thank you for choosing the Sena 10S, Motorcycle Bluetooth Communication System. With the 10S, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or voice instructions of GPS navigations wirelessly, and have intercom conversations in full duplex with a passenger or other motorcycle riders. The 10S is compliant with the Bluetooth 4.
2 PACKAGE CONTENTS ● Headset Main Unit ● Clamp ● Glued Surface Mounting Adapter Speaker ● Speakers ● Hook and Loop Fasteners for Speakers (4) ● Speaker Pads (Thick) (2) ● Speaker Pads (Thin) (2) Wired Microphone ● Wired Microphone ● Hook and Loop Fasteners for Wired Microphone Wired Boom Microphone
● Wired Boom Microphone ● Hook and Loop Fasteners for Boom Microphone ● Microphone Sponge (2) ● Boom Microphone Holder ● Hook and Loop Fasteners for Holder 3 INSTALLING THE 10S ON YOUR HELMET 3.1 Installing the Main Unit 3.1.1 Using the Clamp Unit 1. Loosen the two screws on the back plate of the clamp unit with the included allen wrench.
2. Insert the back plate of the clamp unit between the internal padding and external shell of the left side of the helmet. 3. Tighten the two screws until the clamp unit is fastened firmly to the helmet. 4. Attach the main unit to the clamp unit until you hear a click. The main unit is now fastened to the clamp unit. 3.1.
2. Peel off the cover of adhesive tape of the glued surface mounting adapter and attach it to the helmet. 3. Make sure that the glued surface mounting plate sticks on the helmet firmly. Maximum adhesion occurs after 24 hours. 4. Attach the clamp unit on the glued surface mounting adapter using two screws. CAUTION: Sena recommends using the clamp unit. The glued surface mounting adapter is provided for convenience, but is not the recommended mounting method. sena is not responsible for its use. 5.
3. Align the arrows on the clamp unit and speaker cables and insert speaker cables into each speaker connector. Note: 1. Three cables connect to the clamp unit. The longest is the cable for the right speaker. The second longest cable is for the left speaker. The shortest cable is for the microphone. 2. If the helmet has deep ear pockets, you can use the speaker pads to bring the speakers closer to your ears. 3.3 Installing the Microphones 3.3.1 Using the Wired Boom Microphone 1.
Note: 1. After you install the wired boom microphone, make sure you reinstall the helmet’s internal padding. 2. You can use the boom microphone holder after attaching the hook and loop fastener for boom microphone holder on it to ensure secure installation. 3. Make sure that the microphone’s receiver is located near your mouth. 4. Adjust the head of the microphone so that the tab is facing away from your mouth. 5.
3.3.2 Using the Wired Microphone If you have a full face helmet, you can use the wired microphone. 1. Peel off the cover of the hook and loop fastener for wired microphone to expose the adhesive tape. Then, attach the hook and loop fastener on the inside of the helmet’s chin guard. 2. Attach the wired microphone to the hook and loop fastener for wired microphone. 3. Align the arrows on the clamp unit and microphone cables and insert the microphone cable into the microphone connector. Note: 1.
4 GETTING STARTED 4.
4.3 Charging You can charge the headset by connecting the supplied USB power & data cable into a computer’s USB port or USB wall charger. You can use any standard micro USB cable to charge the units. The charging LED turns red while charging and turns blue when fully charged. It takes about 2.5 hours to be completely charged. 4.4 Low Battery Warning When the battery is low, the blinking blue LED in stand-by mode turns to red and you will hear mid-tone triple beeps and a voice prompt, “Low battery”. 4.
the Sena Smartphone App for Android or iPhone from www.sena.com/app. 5 PAIRING THE 10S WITH BLUETOOTH DEVICES Before using the 10S Bluetooth headset with any other Bluetooth devices for the first time, you will need to pair them together. You can pair the 10S with Bluetooth mobile phones, Bluetooth stereo devices such as MP3 players, or motorcycle specific Bluetooth GPS navigation, and with other Sena Bluetooth headsets. The pairing operation is required only once for each Bluetooth device.
1. If the GPS is also your preferred Bluetooth stereo music source, you can pair the GPS to the 10S by following the simple procedure in section 5.1, “Mobile Phone Pairing - Mobile Phone, Bluetooth Stereo Device”. 2. You have to use a motorcycle specific GPS, which transmits turn-by-turn voice instructions to the headset by Bluetooth. Most automotive GPS systems do not have this feature. 3. The Sena SR10 is a Bluetooth two-way radio adapter for group communication, and uses Hands-Free Profile.
3. Tap the Jog Dial on any one of the two headsets A and B, and wait unit the LEDs of both headsets turn to blue and intercom connection is automatically established. The two 10S headsets A and B are paired with each other for intercom conversation. If the pairing process is not completed within one minute, the 10S will return to stand-by mode. Pairing A & B 4. You can make other pairing between headsets A and C, and between headsets A and D by following the same procedure as above. 5.
6 MOBILE PHONE, GPS, SR10 6.1 Mobile Phone Call Making and Answering 1. When you have an incoming call, simply tap the Phone Button or the Jog Dial to answer the call. 2. You can also answer the incoming call by loudly speaking any word of your choice if Voice Activated Phone Answering (VOX Phone) is enabled, unless you are connected to intercom. 3. To end a call, tap the Phone Button or press the Jog Dial for 2 seconds until you hear a mid-tone single beep, or wait for the called person to end the call. 4.
back to stand-by mode. Note: 1. Make sure that you connect the mobile phone and the headset to use the speed dial function. 2. You need to assign speed dial numbers before using the speed dial (please refer to section 13.1, “Assigning Speed Dial”). 6.3 GPS Navigation If you pair a Bluetooth GPS to the 10S as described in section 5.2, “Second Mobile Phone Pairing”, you can listen to GPS instructions wirelessly. Rotate the Jog Dial clockwise or counter-clockwise to adjust volume.
7 STEREO MUSIC 7.1 By Bluetooth Wireless Stereo The Bluetooth audio device must be paired with the 10S by following the “Bluetooth Stereo Device Pairing” procedures described in the section 7.1. The 10S supports the Audio/Video Remote Control Profile (AVRCP), so if your Bluetooth audio device also supports the AVRCP, you can use the 10S to remotely control music playback. Not only can you adjust the volume but you can also use functions such as play, pause, next track and previous track. 1.
7.3 Music Sharing You can start sharing music with an intercom friend using Bluetooth stereo music during a two-way intercom conversation (please refer to section 8.1, “Two-way Intercom”). When you terminate music sharing, you can go back to the intercom conversation. To start or terminate sharing music, press the Jog Dial for 1 second during an intercom conversation until you hear a double beep. To track forward or track back, rotate while pressing the Jog Dial clockwise or counter-clockwise. Note: 1.
8 INTERCOM Please make sure your intercom devices are paired as described in section 5.4, “Intercom Pairing”. 8.1 Two-way Intercom 8.1.1 Starting Two-way Intercom You can start an intercom conversation with one of any intercom friends by tapping the Jog Dial: Tap the Jog Dial once to intercom with the first intercom friend, tap the Jog Dial twice to intercom with the second intercom friend, and tap the Jog Dial three times to intercom with the third intercom friend. Start Two-way Intercom Conversation 8.1.
2. Start an intercom conversation with one of the two friends in your intercom group. For example, you (A) may start an intercom conversation with the intercom friend (B). Or intercom friend (B) may start an intercom call with you (A). 3. The second intercom friend (C) may join the intercom by making an intercom call to you (A). 4. Now you (A) and two 10S intercom friends (B & C) are having a three-way conference intercom. 8.2.
example, by single tapping the Jog Dial, you can terminate the intercom connection with just the first intercom friend (B). However, you still have the intercom connection with your second intercom friend (C). Jog Dial Operation Result Press for 1” Disconnect (B) & (C) Single tap Disconnect (B) Double tap Disconnect (C) End Three-way Intercom 8.3 Four-way Intercom 8.3.
9 THREE-WAY CONFERENCE PHONE CALL WITH INTERCOM PARTICIPANT 1. When you have an incoming mobile phone call during an intercom conversation, you will hear a ringtone. You can choose whether to 1) answer the mobile phone call and stop the intercom conversation, or 2) reject the phone call and stay on the intercom conversation. a. To answer the phone call and stop the intercom conversation, tap the Phone Button or the Jog Dial. The VOX Phone feature does not work if you are connected to intercom.
10 GROUP INTERCOM Group Intercom allows you to instantly create a multi-way conference intercom with three other most recently paired headsets. 1. Go through intercom pairing with up to three headsets you want to have Group Intercom with. 2. Press the Jog Dial for 3 seconds to begin Group Intercom. The LED will flash green and you will hear a voice prompt, “Group intercom”. 3. To terminate Group Intercom, press the Jog Dial for 1 second during Group Intercom.
3. Perform the operation required for handsfree pairing on the non-Sena Bluetooth headset (refer to the User’s Guide for the headsets you want to use). The 10S will automatically pair with a non-Sena Bluetooth headset when each are in pairing mode. 11.2 Two-way Universal Intercom You can initiate the Universal Intercom connection with non-Sena Bluetooth headsets using the same intercom connection method as you would between other Sena headsets.
4. Now you (A), non-Sena Bluetooth headset (B), and the other 10S (C) are having a three-way conference intercom. 5. You may disconnect three-way Universal Intercom using the same way as you do in normal three-way intercom. Please refer to section 8.2.2, “End Three-way Intercom”. 11.
3. The non-Sena Bluetooth headset (D) may join the conference intercom by making an intercom call to the 10S (C). 4. Now two 10S headsets (A & C) and two non-Sena Bluetooth headsets (B & D) are connected with the four-way Universal Intercom. You may disconnect a four-way Universal Intercom using the same way as you do in a normal four-way intercom. Please refer to section 8.3.2, “End Four-way Intercom”. 11.4.
12 FM RADIO 12.1 FM Radio On/Off To turn on the FM radio, press the Phone Button for 1 second until you hear a mid-toned double beep sound. You will then hear a voice prompt, “FM on”. To turn off the FM radio, press the Phone Button for 1 second until you hear a voice prompt, “FM off”. When you power it off, the 10S will remember the last station frequency. When you power it on, the last station frequency will be playing. 12.
12.5 Temporary Preset With the temporary preset function, you may temporarily preset stations automatically without changing the existing preset stations. Tap the Phone Button three times to automatically scan for 10 temporary preset stations. The temporary preset stations will be cleared when the system is powered off. 12.6 Region Selection You can select the proper FM frequency region from the Sena Device Manager.
13 FUNCTION PRIORITY The 10S operates in the following order of priority: (highest) Mobile phone Intercom Stereo music by audio cable Music sharing by Bluetooth stereo music FM Radio (lowest) Bluetooth stereo music A lower priority function is always interrupted by a higher priority function. For example, stereo music is interrupted by intercom call, and an intercom conversation is interrupted by an incoming mobile phone call.
14 CONFIGURATION SETTING You can set the configuration of the 10S by the voice menu instruction described below. 1. To enter into voice configuration menu, press and hold the Jog Dial for 12 seconds until the LED shows solid blue and you hear high toned double beeps. You will also hear a voice prompt, “Configuration menu”. 2. Rotate the Jog Dial to navigate between the menus. You will hear voice prompts for each menu item as below. 3.
Factory Default N/A Execute Tap the Phone Button 1. To assign a phone number as a speed dial, rotate the Jog Dial until you hear a voice prompt, “Speed dial”. 2. Tap the Phone Button, and you will hear a voice prompt, “Speed dial one” and “Phone connected”. 3. Rotate the Jog Dial to select one of three speed dial numbers and you hear a voice prompt, “Speed dial (#)”. 4. Call a phone number you want to assign and you will hear a voice prompt, “Save speed dial (#)”.
call. 14.4 Enabling/Disabling Voice Activated Intercom Voice Prompt “VOX intercom” Factory Default Disable Enable Tap the Phone Button Disable Tap the Jog Dial If this feature is enabled, you can initiate an intercom conversation with the last connected intercom friend by voice. When you want to start intercom, say a word such as “Hello” loudly or blow air into the microphone.
- Voice prompts for battery level indicator - Voice prompts for speed dial - Voice prompts for FM radio functions 14.7 Enabling/Disabling RDS AF Voice Prompt “RDS AF setting” Factory Default Enable Enable Tap the Phone Button Disable Tap the Jog Dial RDS AF allows a receiver to re-tune to the second frequency location when the first signal becomes too weak. With RDS AF enabled on the receiver, a radio station with more than one frequency can be used. 14.
14.10 Delete All Bluetooth Pairing Information Voice Prompt “Delete all pairings” Factory Default Execute N/A Tap the Phone Button To delete all Bluetooth pairing information of the 10S, rotate the Jog Dial until you hear a voice prompt, “Delete all pairings”, and tap the Phone Button to confirm. 14.
Execute Tap the Phone Button To exit voice configuration menu and get back to stand-by mode, rotate the Jog Dial until you hear a voice prompt, “Exit configuration”, and tap the Phone Button to confirm.
15 REMOTE CONTROL You can remotely control the 10S via Bluetooth using the Handlebar Remote (sold separately). This eliminates the need to take off your hand for button operations. Your 10S and the Handlebar Remote must be paired together before use. 15.1 Pairing with the Handlebar Remote 1. Turn on the 10S and the Handlebar Remote. 2. Press the Jog Dial for 12 seconds to enter the configuration menu. Rotate the Jog Dial until you hear a voice prompt saying, “Remote control pairing”.
Play/Pause Bluetooth music Press the Joystick for 1 second - Track forward/back Move the Joystick left or right for 1 second - FM radio on/off Press the Rear Button for 1 second - Select preset Tap the Rear Button - Seek stations Move the Joystick left or right for 1 second - Scan up FM band Double tap the Rear Button - Stop scanning Double tap the Rear Button - Save preset while scanning Tap the Rear Button - Music FM radio Handlebar Remote Button Operation Table
16 FIRMWARE UPGRADE The 10S supports firmware upgrades. You can update the firmware using the Sena Device Manager (please refer to section 4.6.1, “Sena Device Manager”). Please visit Sena Bluetooth website at www.sena.com to check the latest software downloads.
17 TROUBLESHOOTING 17.1 Intercom Failure When you try to start an intercom conversation with an intercom friend who is unavailable within range or already having a conference intercom with other riders or a mobile phone call, you will hear a low tone double beep signifying an intercom busy signal. In this case, you have to try again later. 17.
18 OPERATION QUICK REFERENCE Type Basic Function Function Button Command LED Beep Power on Press the Phone Button and the Jog Dial for 1 second Solid blue Ascending beeps Power off Press the Phone Button and the Jog Dial Solid red Descending beeps Volume adjustment Rotate the Jog Dial - - Mobile phone pairing Press the Phone Button for 5 seconds Blue & red alternatively flashing High tone multiple beeps Press the Jog Dial for 8 seconds Red flashing Multiple beeps Second mobile phone
FM radio on/off Press the Phone Button for 1 second - Mid-tone double beeps Select preset Tap the Phone Button - Mid-tone single beep Seek stations Rotate the Jog Dial while pressing - High tone triple beeps Scan up FM band Double tap the Phone Button - - Stop scanning Double tap the Phone Button - High tone double beeps Save preset while scanning Tap the Phone Button - High tone double beeps Press the Phone Button for 12 seconds Solid red High tone double beeps - - FM radio Fa
CERTIFICATION AND SAFETY APPROVALS FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Bluetooth License ® The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license. Other trademarks and trade names are those of their respective owners.
● In some regions, it is prohibited by law to ride motorcycles or bicycles while wearing headsets. Therefore be certain to comply with all relevant laws in the region before using the product. ● Use of the product at a high volume for a long period of time may damage your eardrums or hearing ability. Keep the volume at a modest level. ● Do not cause impact to the product or touch it with sharp tools as this may damage the product.
Limited Warranty Limited Warranty Sena Technologies, Inc. (“Sena”) guarantees the product quality based on the technical specification stated in the product manual, and data regarding product warranty. Here, product warranty extends to the product only. Sena will not be liable for any loss, damage of human life, or loss of property which may result from using the product beyond defective parts or flaws that occur due to problems in manufacture.
ATVs, or quad-bikes (hereinafter called as "transportation means"), you must take complete caution regardless of the location of such operation. ● Use of the product on the road may cause such risks as fracture, serious disability, or death. ● Risk factors, which may occur when you use the product, may be due to errors of the manufacturer, its agents, or third parties which are involved in the manufacturing. ● Risk factors, which may occur when you use the product, may be unforeseeable.
which occur due to the following events. In the event the product is misused or used for purposes other than its intended purposes. In the event the product is damaged because the user does not follow the content of the product manual. In the event the product is damaged because it has been left unattended or has undergone any other accident. In the event the product is damaged because the user has used any parts or software which are not provided by the manufacturer.
1.0.0 CERTIFICATION ET HOMOLOGATION EN TERMES DE SÉ CURITÉ Déclaration de conformité FCC Cet appareil est en conformité avec la partie 15 de la réglementation FCC. L'exploitation est autorisée aux deux conditions suivantes : (1) Cet appareil ne doit pas créer d’interférences préjudiciables et (2) Cet appareil doit accepter toutes les interférences reçues, y compris celles qui pourraient entraver son bon fonctionnement.
Déclaration de conformité IC (Industrie Canada) Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) Cet appareil ne doit pas créer d'interférences. (2) Cet appareil doit accepter toutes les interférences reçues, y compris celles qui pourraient entraver son bon fonctionnement.
Utilisation du produit ● Dans certaines régions, la loi interdit le port d'écouteurs en étant à moto ou à vélo. Assurez-vous donc de respecter toutes les lois correspondantes dans la région avant d'utiliser le produit. ● L'utilisation du produit à volume élevé pendant une période prolongée peut endommager les tympans ou la capacité auditive. Garder le volume sonore à un niveau modéré. ● Ne pas heurter le produit ou le toucher avec des outils tranchants car cela pourrait l'endommager.
● Ne jamais utiliser un chargeur endommagé. Il pourrait exploser et/ou causer des accidents. ● La durée de vie de la batterie dépend des conditions, des facteurs environnementaux, des fonctions en cours d'utilisation du produit et des appareils utilisés conjointement. Garantie limitée Garantie limitée Sena Technologies, Inc. (« Sena ») garantit la qualité du produit sur la base des caractéristiques techniques énoncées dans le manuel du produit et les données concernant la garantie du produit.
● Sena, en collaboration avec les employés, responsables, partenaires, filiales, représentants, agents, entreprises et fournisseurs impliqués, seuls vendeurs de Sena (collectivement désignés comme « l'entreprise ») vous recommandent, avant d'utiliser le produit et des appareils similaires de différentes marques y compris leurs modèles dérivés, de recueillir à l'avance toutes les informations pertinentes et d'être entièrement préparé quant aux conditions météorologiques et routières ainsi qu'à l'état de la
POUR LE PRODUIT PAR L'ACHETEUR. Exonération de responsabilités Outre les dommages pouvant survenir en raison de l'utilisation du produit, Sena n'est pas tenu responsable des dommages du produit survenant en raison des situations suivantes. ● Dans le cas où il est fait mauvais usage du produit ou qu'il est utilisé dans un but autre que celui prévu. ● Dans le cas où le produit est endommagé car l'utilisateur ne suit pas le contenu du manuel du produit.
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. « Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.