User Manual

ManualsBrandsSena ManualsAccessoriesSena 20S-01 Motorcycle Bluetooth 4.1 Communication System with HD Audio and Advanced Noise Control (Single)

Table Of Contents

1 INTRODUCTION
2 PACKAGE CONTENTS
3 INSTALLING THE 20S ON YOUR HELMET
- 3.1 Helmet Installation
- 3.2 Glued Surface Mounting Adapter
- 3.3 Switching the Microphone
4 GETTING STARTED
- 4.1 Charging
- 4.2 Low Battery Warning
- 4.3 Checking the Battery Level
- 4.4 Powering On and Off
- 4.5 Volume Adjustment
- 4.6 Software
5 PAIRING THE 20S WITH BLUETOOTH DEVICES
- 5.1 Mobile Phone Pairing
- 5.2 Second Mobile phone Pairing
- 5.3 Bluetooth Stereo Device Pairing
- 5.4 Bluetooth GPS Navigation Pairing
- 5.5 Pairing with the Sena SR10, Bluetooth Two-way Radio Adapter
6 PAIRING WITH SELECTIVE PROFILE: A2DP STEREO OR HANDSFREE
7 MOBILE PHONE CALL MAKING AND ANSWERING
- 7.1 Mobile Phone Call Making and Answering
- 7.2 Speed Dialing
- 7.3 Intercom and Mobile Phone Call
8 STEREO MUSIC
- 8.1 By Stereo Audio Cable
- 8.2 By Bluetooth Wireless Stereo
- 8.3 Music Sharing
9 GPS NAVIGATION
10 SENA SR10, TWO-WAY RADIO ADAPTER
11 FM RADIO
- 11.1 FM Radio On / Off
- 11.2 Preset Stations
- 11.3 Seek and Save
- 11.4 Scan and Save
- 11.5 Temporary Preset
- 11.6 Region Selection
12 AMBIENT MODE
13 VOICE COMMAND
14 INTERCOM PAIRING
- 14.1 Pairing with Other 20S Headsets for Intercom Conversation
- 14.2 Pairing with Other Sena Headset Models for Intercom Conversation
15 TWO-WAY & MULTI-WAY INTERCOM
- 15.2 Multi-way Intercom
- 15.3 Intercom Failure
- 15.4 Intercom Reconnection
16 THREE-WAY CONFERENCE PHONE CALL WITH INTERCOM PARTICIPANT
17 GROUP INTERCOM
18 UNIVERSAL INTERCOM
- 18.1 Universal Intercom Pairing
- 18.2 Two-way Universal Intercom
- 18.3 Three-way Universal Intercom
- 18.4 Four-way Universal Intercom
19 FUNCTION PRIORITY
20 20S CONFIGURATION SETTING
- 20.1 Assigning Speed Dial
- 20.2 Enabling/Disabling Audio Multitasking
- 20.3 Setting Intercom-audio Overlay Sensitivity
- 20.4 Enabling/Disabling Navigation App Support
- 20.5 Enabling/Disabling Audio Boost
- 20.6 Setting Motion Sensor Sensitivity
- 20.7 Enabling/Disabling Voice Activated Phone Answering
- 20.8 Enabling/Disabling HD Intercom
- 20.9 Enabling/Disabling Eight-way Intercom
- 20.10 Enabling/Disabling Voice Prompts
- 20.11 Enabling/Disabling Sidetone
- 20.12 Enabling/Disabling Advanced Noise Control™
- 20.13 Delete All Bluetooth Pairing Information
- 20.14 Universal Intercom Pairing
- 20.15 Exit Voice Configuration Menu
21 RESET TO FACTORY DEFAULT SETTINGS
22 FAULT RESET
23 FIRMWARE UPGRADE
24 SENA BLUETOOTH CONNECTION CASE STUDIES
25 OPERATION QUICK REFERENCE
CERTIFICATION AND SAFETY APPROVALS
- FCC Compliance Statement
- FCC RF Exposure Statement
- FCC Caution
- CE Declaration of Conformity
- Industry Canada Statement
- Bluetooth License
- WEEE (Waste Electrical and Electronic Equipment)
SAFETY INFORMATION
- Product Storage and Management
- Product Use
- Battery
PRODUCT WARRANTY AND DISCLAIMER
- Limited Warranty
- Warranty Exclusions
- Warranty Service
- Return for Full Refund

20S

22 FAULT RESET

When the 20S is not working properly or is in faulty status for any

reason, you may reset by pushing the pin-hole reset button at the

back of the headset main unit. Insert a paper clip into the reset pin-

hole and press the reset button for a second with light pressure. The

20S will be switched off, and you have to turn the system back on and

try again. However, this will not restore the headset to factory default

settings.

23 FIRMWARE UPGRADE

The 20S supports rmware upgrade function. Please visit Sena

Bluetooth web site at www.sena.com to check the latest software

downloads.