. Bluetooth® Headset & Intercom for Scooters and Motorcycles www.sena.
© 1998-2015 Sena Technologies, Inc. All rights reserved. Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior notice. Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. 20S™, PRISM™, Snowtalk™, 3S™, SMH10™, SMH5™, SMH5-FM™, SPH10™, SPH10H-FM™, SMH10R™, SPH10S™, SPH10H™, SR10™, SR10i™, SMH10™, EXPAND™, Bluetooth Pack for GoPro® are trademarks of Sena Technologies, Inc. or its subsidiaries.
S CONTENTS 1. INTRODUCTION .................................................................................4 2. PACKAGE CONTENTS ........................................................................5 3. GETTING STARTED .............................................................................8 Installing the 3S on Your Helmet - Boom Microphone Type ......................... 8 Installing the 3S on Your Helmet - Wired Microphone Type .........................
3S 1. INTRODUCTION Thank you for choosing the Sena 3S, Bluetooth Headset and Intercom for Scooters and Motorcycles. With the 3S, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or GPS navigation voice instructions via Bluetooth, and have intercom conversations in full duplex with a passenger or other riders.
3S English 2.
3S Status LED Pin-hole Reset Button (+) Button (Phone, Music) USB Power & Data Cable Hook and Loop Fasteners for Speakers Hook and Loop Fastener for Microphone Double Sided Adhesive Tape Speakers (–) Button (Intercom) Microphone DC Power Charging & Firmware Upgrade Port Wired Microphone Type 6
3S Status LED English Pin-hole Reset Button (+) Button (Phone, Music) Attachable Boom Microphone USB Power & Data Cable Hook and Loop Fasteners for Speakers Hook and Loop Fastener for Microphone Microphone Sponges Double Sided Adhesive Tape Speakers Microphone connector (–) Button (Intercom) DC Power Charging & Firmware Upgrade Port Attachable Boom Microphone Type 7
3S 3. GETTING STARTED Installing the 3S on Your Helmet - Boom Microphone Type 1. Peel off the hook fasteners for the speakers and attach them on the back sides of the speakers. 2. Attach the loop fasteners for the speakers in the deep ear pockets of your helmet. 3. Place the speakers in the helmet along with the hook and loop fasteners, centered to your ear. 4. Locate the boom microphone as closely as possible to your mouth when wearing the helmet. 5.
3S 3 4 1. Peel off the hook fasteners for the speakers and attach them on the back sides of the speakers. 2. Attach the loop fasteners for the speakers in the deep ear pockets of your helmet. 3. Place the speakers in the helmet along with the hook and loop fasteners, centered to your ear. 4. Locate a suitable surface on the left side of your helmet to attach the unit, clean the location with a moistened towel, and allow to dry thoroughly. 5.
3S 1 3 4 2 10
3S 5 1. Peel off the hook fasteners for the speakers and attach them on the back sides of the speakers. 2. Attach the loop fasteners for the speakers in the deep ear pockets of your helmet. 3. Place the speakers in the helmet along with the hook and loop fasteners, centered to your ear. 4. Locate a suitable surface on the left side of your helmet to attach the unit, clean the location with a moistened towel, and allow to dry thoroughly. 5.
3S 1 3 4 2 12
3S Charging the 3S Note: Please make sure to take off your 3S-installed helmet while charging. Powering On Press and hold the (+) Button and the (–) Button at the same time for 1 second to power on. The blue LED turns on and you will hear ascending beeps and “Hello”. Powering Off Press the (+) Button and the (–) Button at the same time. The red LED turns on for about 2 seconds until it turns off completely and you will hear “Goodbye” and descending beeps.
3S Checking Battery Level You can check the battery level in two different ways when the headset is powering on. LED Indicator 7HEN THE HEADSET IS POWERING ON THE RED ,%$ mASHES RAPIDLY INDICATING the battery level. LED Wired Microphone Type Note: 1. The USB power & data cable is also used for firmware upgrade of the 3S. 2. The USB wall charger is not included in the package.
3S Adjusting the Volume Level You can easily adjust the volume by pressing the (+) Button or the (–) Button. You will hear a beep when the volume reaches maximum or minimum level. The volume is set and maintained independently at different levels for each audio source even when you turn off and on the headset. For example, once you set the volume for mobile phone handsfree, it will not change even if you adjust the volume when you hear Bluetooth MP3 music.
3S Function 4. OPERATION QUICK REFERENCE Function 5 sec. Operations 1 sec. 1 sec. 1 press + Power On/Off Volume Adjustment 1 press + Power On 1 press 1 press Bluetooth Pairing (Phone, MP3, GPS) Power Off 2) Select Sena 3S Sena 3S v1.1 or 3) Enter pairing A 1) 5 sec. 2) 1 sec. Intercom Pairing 16 Operations 1) B 5 sec. Start & End Intercom Conversation 1 sec. 10 sec.
3S Operations Function 1 press English Operations Function 1 sec. or Answer 2 sec. 2 sec. Music End Mobile Phone * 3 sec. 2 sec. Voice Dial * 3 sec. * You can use “Voice Dial” and “Redial” only in stand-by mode. 2 sec.
3S 5. PAIRING AND USING THE 3S WITH BLUETOOTH DEVICES Mobile Phone Pairing 1 Turn on the 3S and press and hold the (+) Button for 5 seconds until THE ,%$ mASHES RED AND BLUE ALTERNATELY AND YOU HEAR MULTIPLE BEEPS You will hear a voice prompt saying “Phone pairing”. 2. Search for Bluetooth devices on your mobile phone. Select the Sena 3S in the list of the devices detected on the mobile phone. 3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.
3S 1st Mobile Phone 2nd Mobile Phone HFP + A2DP HFP 3S Multipoint Mobile Phones Pairing Bluetooth Stereo Device Pairing Bluetooth GPS Navigation Pairing You can listen to voice instruction from Bluetooth GPS navigation.
3S Multipoint GPS Pairing If you use GPS only for turn-by-turn voice instructions, not for Bluetooth stereo music streaming, multipoint pairing is recommended for the GPS connection. Multipoint Bluetooth pairing allows the 3S to connect two (&0 DEVICES AT THE SAME TIME MOBILE PHONE AND '03 NAVIGATION &OLLOW the steps below to pair the GPS using the multipoint pairing. 1.
3S GPS Pairing as Mobile Phone Mobile Phone GPS Navigation English If GPS is not only used for turn-by-turn voice instructions but also is your preferred Bluetooth stereo music source, you can pair the GPS to the 3S by following the simple procedures in “Mobile Phone Pairing”. When you do this, the 3S thinks the GPS is a mobile phone. But the 3S can directly pair an additional mobile phone.
3S Mobile Phone Call Making and Answering 1. When you have an incoming call, simply press the (+) Button to answer the call. 2. You can also answer the incoming call by loudly speaking any word of your choice if Voice Activated Phone Answering, VOX phone is enabled. (Refer to “Enabling/Disabling Voice Activated Phone Answering” for details.) 3. To end a call, press and hold the (+) Button for 2 seconds until you hear a mid-tone single beep, or wait for the called person to end the call. 4.
3S Starting and Ending Intercom Conversation Pairing with Other 3S Headsets for Intercom Conversation 1. You can start an intercom conversation with your intercom friend by pressing and holding the (–) Button for 1 second. 2. To terminate an intercom conversation, press and hold the (–) Button for 1 second again. The 3S can be paired with another headset for Bluetooth intercom conversation. Intercom and Mobile Phone Call 1.
3S mobile phone call because intercom has lower priority than mobile call. You have to hang up the mobile phone call to make or receive an intercom call. Intercom Failure When you try to start an intercom conversation with an intercom friend who is already having a mobile phone call with another person, you will hear a low tone double beep signifying a busy signal. You will also hear a voice prompt saying “Intercom failed, try again later”. In this case, you have to try again later.
3S 4HE VOICE PROMPTS FOR EACH MENU ITEM ARE AS BELOW Voice Prompt Enabling/Disabling Voice Activated Phone Answering Voice Prompt “VOX phone” Factory Default Enable Enable / Disable Press the (–) Button If this feature is enabled, you can answer incoming calls by simply saying a word loudly enough, unless you are connected to intercom. For example, when you hear a series of beeps for an incoming call, you can answer the phone by saying “Hello” or any other word loudly.
3S Reset to Factory Default Setting Voice Prompt Factory Default Execute “Factory reset” N/A Press the (–) Button To restore factory default settings on the 3S, press and hold the (+) Button until you hear a voice prompt, “Factory reset”. Press the (–) "UTTON TO CONlRM 4HE 3 POWERS OFF WITH A VOICE PROMPT hHeadset reset, goodbye”.
3S English 8. FIRMWARE UPGRADE 4HE 3 SUPPORTS lRMWARE UPGRADE FUNCTION 0LEASE VISIT 3ENA "LUETOOTH web site at www.sena.com to check the latest software downloads.
3S CERTIFICATION AND SAFETY APPROVALS FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject TO THE FOLLOWING TWO CONDITIONS (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules.
3S WEEE (Waste Electrical and Electronic Equipment ) This device complies with Industry Canada license-exempt RSS STANDARD S /PERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
3S SAFETY INFORMATION • Do not store the product in humid environments, especially for long time storage. Please ensure that the product is properly used by observing the warnings and cautions below to prevent any risk and/or damage to property. Product Use Product Storage and Management • Keep the product free of dust. It may damage mechanical and electronic parts of the product.
3S • When using the product, be certain to conform to laws regarding the use of communications devices while riding. • Do not put the product where it may hamper the rider's vision or MANIPULATE IT WHILE RIDING 4HIS MAY CAUSE TRAFlC ACCIDENTS • Before riding, fasten the product to the helmet, and double-check that it is fastened. Separation of the product while riding may cause damage to the product or accidents. • If the product is damaged, stop using it immediately.
3S • Store the battery at temperatures of 15°C~25°C (59°F~77°F). Higher or lower temperatures may reduce the capacity and life of the battery, or may cause temporary non-operation. Do not use the product in sub-zero temperature, because it may cause serious reduction of the battery performance. • )F YOU APPLY HEAT TO THE BATTERY OR THROW IT INTO lRE IT MAY EXPLODE • Do not use the product with a damaged battery. It may explode and/or cause accidents. • Never use a damaged charger.
3S Notice and Waiver By buying and using this product, you relinquish considerable legal rights including any claim for compensation for damages. Therefore, be certain to read and understand the following terms and conditions before using the product. Use of this product will constitute consent to this agreement, and forfeiture of rights to all claims. If you do not consent to all the terms and conditions of this agreement, return the product for a refund. (Refer to the section “Return for Full Refund”.
3S • Risk factors, which may occur when you use the product, may be due to errors of the manufacturer, its agents, or third parties which are involved in the manufacturing. • Risk factors, which may occur when you use the product, may be unforeseeable. Therefore, you must take full responsibility for any damage or loss caused by all risk factors which may occur when using the product. • When you use the product, use good judgment; never use it under THE INmUENCE OF ALCOHOL 6.
3S Liabilities Disclaimer In addition to damages which may occur due to the use of the product, Sena will not be liable for damages of the product which occur due to the following events. • In the event the product is misused or used for purposes other than its intended purposes. • In the event the product is damaged because the user does not follow the content of the product manual. • In the event the product is damaged because it has been left unattended or has undergone any other accident.
3S Warranty Service To obtain product warranty service, send the defective product, at your expense, to the manufacturer or the seller along with proof of purchase (a RECEIPT THAT SHOWS THE PURCHASE DATE A PRODUCT REGISTRATION CERTIlCATE OF the Website, and other relevant information). Take necessary measures to protect the product. In order to get a refund or replacement, you must include the whole package as it was purchased.
1.1.2 www.sena.com User's Guide for Firmware v1.1.