www.senabluetooth.
SMH10 CONTENTS INTRODUCTION 3 • Intercom Reconnection 14 PACKAGE CONTENTS 4 • Stereo Music 14 INSTALLING THE SMH10 ON YOUR HELMET 5 • Function Priority 15 POWERING ON/OFF AND CHARGING 7 • RESET TO FACTORY DEFAULT SETTINGS 16 • Powering On 7 • FAULT RESET 16 • Powering Off 7 OPERATION QUICK REFERENCE 16 • Charging 7 BATTERY INFORMATION 17 • Low Battery Warning 8 MAINTENANCE AND CARE 17 8 DISPOSAL 18 • Mobile Phone Pairing 8 CERTIFICATION AND SAFETY APPROVALS 19 • Bluet
SMH10 English INTRODUCTION The SMH10 features: • Bluetooth hands-free for Bluetooth mobile phones • Bluetooth stereo headset for Bluetooth audio devices such as MP3 players Thank you for choosing the SENA SMH10, Bluetooth Stereo Headset and Intercom • Bluetooth headset or stereo headset for Bluetooth GPS navigations for motorcycles.
SMH10 • Speaker-Microphone Clamp Unit PACKAGE CONTENTS Speakers • Headset Main Unit DC Power Charging port Microphone Phone Button • Making and Answering a mobile phone call • Entering into Mobile Phone Pairing Mode • Entering into Bluetooth Audio Device Pairing • DC Power Charger Mode (MP3, GPS navigation) • Entering into Voice Activated Phone Answering Setting Mode Jog Dial • USB Power Cable • Cigarette Charger • Start and End an Intercom Conversation • Volume adjustment by rotating • Play and Pa
SMH10 • Microphone Sponges • Hex Key (Allen Wrench) English • Velcro Pads INSTALLING THE SMH10 ON YOUR HELMET 1. Insert the back plate of the Speaker-Microphone clamp unit between the internal padding and external shell of the helmet. Please make sure that the microphone is located properly close to your mouth when you wear the helmet. Insert 2. Please adjust the direction of the microphone so that the triangular mark on the microphone is pointing towards your mouth.
SMH10 3. If you have any problem to clamp the Speaker-Microphone unit on the helmet for any reason, you may use the glued surface mounting adaptor to attach the Speaker-Microphone unit on the external surface of the helmet. • Remove the back plate of the Speaker-Microphone clamp unit by loosening the two screws with the enclosed Hex Key. Warning: Sena recommends the clamp unit over the glued surface mounting adaptor.
SMH10 5. To remove the main headset from the Speaker-Microphone clamp unit, hold the POWERING ON/OFF AND CHARGING English lower part of the Speaker-Microphone clamp unit with your thumb and gently press down the hook on the upper part of the headset main unit with your index finger until it clicks out. You may have to do this to charge up or to carry the headset To power on and off the headset, you don’t need to press and hold any button for main unit. several seconds.
SMH10 • Low Battery Warning When the battery is low, the blinking blue LED in stand-by mode turns to red PAIRING THE SMH10 WITH BLUETOOTH DEVICES and you will hear mid-tone triple beeps. Before using the SMH10 Bluetooth headset with any of Bluetooth devices for the first time, you need to do the pairing operation. It can be paired with Bluetooth mobile phones, Bluetooth audio devices such as MP3 or GPS, and with other SMH10 Bluetooth headsets.
SMH10 4. Press and hold the Jog Dial of the headset B for 5 seconds until red LED starts 1. The procedure is the same with the procedure of “Mobile Phone Pairing”, except to flash rapidly. the SMH10 must be paired as Stereo Headset. 5. Simply tap the Jog Dial of any one of the two headset A or B (It doesn’t matter 2.
SMH10 A B A C B D A C B D Pairing A & C C D Pairing A & D Pairing C & D 7. Then, you can also make other pairings between the headsets B, C and D by 8. Four headsets are completely multi-paired so that four persons can have Intercom following the same procedure as above. (Headset B is paired with Headset C and conversations with each other. D, and also Head C is paired with Headset D) 9.
SMH10 Headset B st Headset C st st Headset D USING THE SMH10 English Headset A st isof 1A isof 1B isof 1C of 1 D D D C is D 2Cnd isof A 2Cnd isof B 2Bnd isof C 2 nd of • Volume Adjustment You can easily adjust the volume by rotating the Jog Dial. You will hear a beep when the volume reaches maximum or minimum level. The volume is set and maintained separately at different levels for each function even when you turn off and on the A 3 3 B 3 1 2 2 3 1 2 headset.
SMH10 4. To transfer a call between the mobile phone and the headset, tap the Jog Dial 1. Press and hold the Phone Button for 8 seconds until the red LED is rapidly during the phone conversation. You will hear a short/long beep when the call is flashing. When you do this, after first 5 seconds you press the button, you will see transferred to the phone/headset. the headset enters into the Mobile Phone Pairing sequence, but you have to keep 5.
SMH10 2. To enable, tap the Jog Dial, then the blue LED flashes for 2 seconds and you connection with any Intercom Friend will be terminated by a single tapping. A will hear double beeps. double or triple tapping will do nothing in this case. 3. To disable, tap the Phone button, then the red LED flashes for 2 seconds and you will hear a single beep.
SMH10 • Intercom Failure • Stereo Music When you try to start an intercom conversation with an Intercom Friend who is You can listen to stereo music in either way: with the enclosed stereo audio cable already having an intercom conversation or a mobile phone call with another person, or by Bluetooth wireless stereo. you can’t make it and will hear low tone double beep as a busy signal. In this case, you have to try again later. 1.
SMH10 • To track forward or track back, rotate while pressing the Jog Dial clockwise or control music playback. So, you may not only adjust the volume but also use the counter clockwise. English Bluetooth audio device also supports the AVRCP, you can use the SMH10 to remotely functions such as play, pause, next track and previous track. • To adjust the volume, rotate the Jog Dial.
SMH10 • RESET TO FACTORY DEFAULT SETTINGS 1. To restore the SMH10 to factory default settings, press and hold the Phone Button OPERATION QUICK REFERENCE for 12 seconds until the LED shows solid red and you hear double beeps. 2. Then within 5 seconds, press the Jog Dial to confirm reset. The headset will be Button Description Duration LED Beep restored to factory setting and switched off automatically.
SMH10 MAINTENANCE AND CARE English BATTERY INFORMATION The SMH10 has an internal, non-removable, rechargeable battery. Do not attempt to The SHM10 should be treated with care and the following suggestions will help you remove the battery from the device as you may damage the device. The battery protect your warranty coverage. can be charged and discharged hundreds of times, but it will eventually wear out. Recharge the battery only with SENA approved chargers designated for this 1.
SMH10 7. Do not paint the device. Paint can clog the moving parts and prevent proper operation. DISPOSAL These suggestions apply equally to the headset main unit, speaker-microphone The crossed-out wheel bin symbol on the product, literature, or clamp unit, or power charger. packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life.
SMH10 English CERTIFICATION AND SAFETY APPROVALS interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. • FCC Compliance Statement - Connect the equipment into an outlet on a circuit different from that to which the This device complies with part 15 of the FCC Rules. Operation is subject to the receiver is connected.
SMH10 requirements and other relevant provisions of Directive 1999/5/EC. For further information please consult http://www.senabluetooth.com. Please note that this WAIVER AND GENERAL RELEASE product uses radio frequency bands not harmonized within EU.
SMH10 1. You, your heirs, legal representatives, successors or assigns, hereby voluntarily the Device while actively involved in traffic.
SMH10 strains, fractures, partial and/or total paralysis, death or other ailments that could This warranty is limited to the repair and/or replacement, at SENA’s discretion, of cause serious disability; (b) these risks and dangers may be caused by the negligence defective or non-conforming Product, and SENA shall not be responsible for the of the manufacturers or its agents or any third party involved in designing or manufacturing failure of the Product to perform specified functions, or any other non-
SMH10 SHALL BE LIABLE FOR ANY OTHER DAMAGES, INCLUDING BUT NOT LIMITED WARNING English TO DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION IN CONTRACT OR TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY), SUCH AS, BUT NOT LIMITED TO, LOSS OF ANTICIPATED SENA informs that using this device in public traffic may not be authorized by PROFITS OR BENEFITS RESULTING FROM, OR ARISING OUT OF, OR IN CONNECTION the law.
www.senabluetooth.com V1.0.