Bluetooth® Headset & Intercom for Scooters and Motorcycles www.SenaBluetooth.
SMH3 CONTENTS 1. INTRODUCTION ..................................................................................3 2. PACKAGE CONTENTS ........................................................................4 3. GETTING STARTED .............................................................................5 Installing the SMH3 on Your Helmet ............................................................. 5 Powering On ..............................................................................................
SMH3 1. INTRODUCTION Thank you for choosing the Sena SMH3, Bluetooth Headset and Intercom for Scooters and Motorcycles. With the SMH3, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or GPS navigation voice instructions via Bluetooth, and have intercom conversations in full duplex with a passenger or other riders. The SMH3 is compliant with the Bluetooth specification 3.
SMH3 2. PACKAGE CONTENTS 2.
SMH3 3. GETTING STARTED English 3. GETTING STARTED Installing the SMH3 on Your Helmet 1. Place the speaker-microphone unit in the helmet along with the velcro pads, centered to your ear, in the ear pockets of the helmet. Locate the boom microphone as closely as possible to your mouth when wearing the helmet. 2. Hide the wire under the helmet padding after the installation.
SMH3 Powering On Press and hold the (+) Button and the (-) Button at the same time for 1 second to power on. The blue LED turns on and you will hear ascending beeps and “Hello”. 3 Powering Off Press the (+) Button and the (-) Button at the same time. The red LED turns on for about 2 seconds until it turns off completely and you will hear “Goodbye” and descending beeps.
SMH3 You can check the battery level in two different ways when the headset is powering on. LED Indicator When the headset is powering on, the red LED flashes rapidly indicating the battery level. LED Note: 1. The USB power & data cable is also used for firmware upgrade of the SMH3. 2. The USB wall charger is not included in the package. Any 3rd party USB charger can be used with Sena products if the charger is approved by either FCC, CE, IC, or other locally approved agencies that Sena accepts.
SMH3 Low Battery Warning When the battery is low, the blinking blue LED in stand-by mode turns to red and you will hear mid-tone triple beeps and a voice prompt saying “Low battery”. Adjusting the Volume Level You can easily adjust the volume by pressing the (+) Button or the (-) Button. You will hear a beep when the volume reaches maximum or minimum level. The volume is set and maintained independently at different levels for each audio source even when you turn off and on the headset.
SMH3 4. Sena SMH3 OPERATION QUICK REFERENCE 1) 5 sec. Sena SMH3 v1.0 Operations Function 1 sec. 1 sec. + 1 press Volume Adjustment English 4. OPERATION QUICK REFERENCE Power On/Off Operations Function Bluetooth Pairing (Phone, MP3, GPS) 1 press or 1) 5 sec. 2) 1 sec. Intercom Pairing Sena SMH3 Sena SMH3 v1.0 Sena SMH3 v1.0 3) Enter pairing A 2) Select Sena SMH3 B 5 sec. Start & End Intercom Conversation PIN 1 sec. 10 sec.
SMH3 Operations Function Operations Function 1 press 1 sec. or Answer 2 sec. 2 sec. Music End Mobile Phone 3 sec. Voice Command 3 sec. 2 sec. Reject 10 2 sec.
SMH3 5. PAIRING AND USING THE SMH3 WITH BLUETOOTH DEVICES Mobile Phone Pairing 1 Turn on the SMH3 and press and hold the (+) Button for 5 seconds until the LED flashes red and blue alternately and you hear multiple beeps. You will hear a voice prompt saying “Phone pairing”. 2. Search for Bluetooth devices on your mobile phone. Select the Sena SMH3 in the list of the devices detected on the mobile phone. 3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN. 4.
SMH3 1st Mobile Phone 2nd Mobile Phone Note: 1. If Bluetooth connection between the headset and a mobile phone is disconnected, press and hold the (+) Button for 3 seconds to recover the Bluetooth connection immediately. 2. If Bluetooth connection between the headset and a media player is disconnected, press and hold the (+) Button for 1 second to recover the Bluetooth connection and play.
SMH3 Multipoint GPS Pairing 1. Turn on the headset and press and hold the (-) Button for 5 seconds until the red LED is rapidly flashing and you hear multiple beeps. 2. Within 2 seconds, press and hold the (+) Button for 1 second, then the LED turns to blue flashing and the beeps turn to high tone double beeps. You will hear a voice prompt saying “Multipoint pairing”. 3. Search for Bluetooth devices on the GPS navigation screen. Select the Sena SMH3 in the list of the devices detected on the GPS. 4.
SMH3 GPS Pairing as Mobile Phone Mobile Phone GPS Navigation If GPS is not only used for turn-by-turn voice instructions but also is your preferred Bluetooth stereo music source, you can pair the GPS to the SMH3 by following the simple procedures in “Mobile Phone Pairing”. When you do this, the SMH3 thinks the GPS is a mobile phone. But the SMH3 can directly pair an additional mobile phone.
SMH3 1. When you have an incoming call, simply press the (+) Button to answer the call. 2. You can also answer the incoming call by loudly speaking any word of your choice if Voice Activated Phone Answering, VOX phone is enabled. (Refer to “Enabling/Disabling Voice Activated Phone Answering” for details.) 3. To end a call, press and hold the (+) Button for 2 seconds until you hear a mid-tone single beep, or wait for the called person to end the call. 4.
SMH3 6. INTERCOM CONVERSATION 6. INTERCOM CONVERSATION Starting and Ending Intercom Conversation Pairing with Other SMH3 Headsets for Intercom Conversation 1. You can start an intercom conversation with your intercom friend by pressing and holding the (-) Button for 1 second. 2. To terminate an intercom conversation, press and hold the (-) Button for 1 second again. The SMH3 can be paired with another headset for Bluetooth intercom conversation. Intercom and Mobile Phone Call 1.
SMH3 Intercom Failure When you try to start an intercom conversation with an intercom friend who is already having a mobile phone call with another person, you will hear a low tone double beep signifying a busy signal. You will also hear a voice prompt saying “Intercom failed, try again later”. In this case, you have to try again later. On the other hand, the intercom friend will hear 4 high tone beeps alerting them that there is an incoming intercom call.
SMH3 The voice prompts for each menu item are as below: (1) VOX phone (2) Voice prompt (3) Delete all pairings (4) Factory reset Voice Prompt Enabling/Disabling Voice Activated Phone Answering Voice Prompt “VOX phone” Factory Default Enable Enable / Disable Press the (-) Button If this feature is enabled, you can answer incoming calls by simply saying a word loudly enough, unless you are connected to intercom.
SMH3 Voice Prompt Factory Default Execute “Factory reset” N/A Press the (-) Button To restore factory default settings on the SMH3, press and hold the (+) Button until you hear a voice prompt, “Factory reset”. Press the (-) Button to confirm. The SMH3 powers off with a voice prompt, “Headset reset, goodbye”.
SMH3 8. FIRMWARE UPGRADE 8. FIRMWARE UPGRADE The SMH3 supports firmware upgrade function. Please visit Sena Bluetooth web site at www.SenaBluetooth.com to check the latest software downloads. BATTERY INFORMATION The product has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery from the device as you may damage the device. The battery can be charged and discharged hundreds of times, but it will eventually wear out.
SMH3 DISPOSAL The product should be treated with care and the following suggestions will help you protect your warranty coverage. The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies to the European Union and other locations where separate collection systems are available.
SMH3 CERTIFICATION AND SAFETY APPROVALS FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
SMH3 Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference. (2) this device must accept any interference, including interference that may cause undesired operation of the device. Bluetooth License The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license.
SMH3 By way of purchasing this Device and not returning it for a full refund (see below), you are irrevocably releasing, indemnifying from any liability, loss, claim and expense (including attorney’s fees) and holding Sena harmless for any bodily injuries, harm or death as well as losses or damages in goods, to any Vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Device under any circumstances or conditions and irrespecti
SMH3 Two-year Limited Warranty Sena Technologies, Inc. (“Sena”) warrants that this product (“Product”) shall conform to and perform in accordance with published technical specifications and the accompanying written materials, and shall be free of defects in materials and workmanship, for a period of two (2) year from the date of purchase by the first consumer purchaser of the Product.
SMH3 Return for Full Refund WARNING IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS, YOU MAY RETURN THIS DEVICE TO SENA FOR A FULL REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 14 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING SO, PLEASE REFER TO THIS SECTION.
1.0.0 www.SenaBluetooth.com User's Guide for Firmware v1.
