USER’S GUIDE Table of Contents: Introduction..........................2-3 Precautions...............................3 Overview.................................. 4 MC24-ES (Short) Powering the. Microphone.............................. 5 Installing the Battery . (MC24-EL only)...................... 6 MC24-EL (Long) Mounting the. Microphone.............................. 7 MC24-ES/EL CONDENSER SHOTGUN MICROPHONE The High-Pass Filter............. 7 Troubleshooting................. 8-9 Specifications........
Thank you for choosing Senal. The Senal MC24-EL and MC24-ES are shotgun microphones that deliver broadcast-quality sound in the studio or on location. They are thoughtfully designed and engineered for demanding video productions, ENG, and broadcast applications. These professional microphones feature a high-grade condenser transducer that captures detailed and accurate sound.
A foam windshield is included to minimize wind noise and to protect the microphone from dust and debris, and a mic clip is included for boom pole or mic stand mounting. Whether in the studio or in the field, the MC24-EL and MC24-ES microphones will deliver proquality, defined, and rich sound for any ENG, outdoor, or broadcast production. Precautions ▪ Please read and follow these instructions and keep this manual in a safe place. ▪ Keep this product away from water and flammable gases or liquids.
Overview High-pass filter switch Grille Battery compartment (MC24-EL only) Microphone ports XLR connector Mic clip Foam windscreen Carry pouch 1/4″-20 to 3/8″-16 bushing 4 ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ Overview
Powering the Microphone The MC24-EL and MC24-ES require power to operate. Both microphones can operate with 48 V phantom power supplied by most professional video cameras, mixing consoles, or recording devices. To power the MC24-EL or MC24-ES, connect an XLR cable to the microphone and activate phantom power on your source.
Installing the Battery (MC24-EL only) The MC24-EL can also run on a single AA battery. To install the battery, follow these steps: 1. Unscrew the base of the microphone and slide it down to expose the battery compartment. Note: The battery compartment cover does not come off. Do not try to force it off of the microphone. 2. Insert the bottom of the battery into the battery compartment according to the orientation on the diagram. 3. Press the top of the battery down into place in the compartment. 4.
Mounting the Microphone A mic clip is included for mounting your microphone on a mic stand or boom pole with a 3/8″ or 5/8″ stud. An adapter bushing comes installed in the mic stand. For mounting on a 5/8″ stud, remove the bushing from the mounting socket of the mic clip with a screwdriver or a coin. Make sure to mount the microphone so that the mic clip is not blocking the side ports of the microphone.
Troubleshooting Problem Solution No sound is being recorded. Make sure your mixer or amplifier is turned on. Make sure phantom power is engaged. (EL only) If using battery power, make sure a fresh battery is installed. Your preamp gain may be turned all the way down. Gradually turn it up until a satisfactory input level is reached. Make sure the microphone is properly connected, and that connections are secure. Check your cable to make sure it’s reliable. Try replacing it with another cable.
Problem Solution Activate the high-pass filter. Too much lowfrequency noise or rumble is being recorded. Turn off air conditioners, fans, heaters, or other devices that might be interfering with your recording. Fit an Auray windscreen (available separately) over the microphone to minimize noise from wind.
Specifications MC24-EL MC24-ES Transducer Condenser Condenser Polar Pattern Hypercardioid Hypercardioid Frequency Response 40 Hz to 20 kHz 40 Hz to 20 kHz Sensitivity 48 V: -32 dB ±2 dB. (1 dB=1 V/Pa at 1 kHz). 48 V: -35 dB ±3 dB. (1 dB=1 V/Pa at 1 kHz) 1.5 V: -36 dB ±2 dB. (1 dB=1 V/Pa at 1 kHz) 10 Output Impedance 48 V: 500 Ω ±20% (at 1 kHz). 1.5 V: 600 Ω ±20% (at 1 kHz) 48 V: 500 Ω ±20% (at 1 kHz) Max. Input SPL 48 V: 130 dB (THD ≤1% at 1 kHz). 1.
MC24-EL MC24-ES Weight 5.2 oz. (148 g) 3.6 oz. (103 g) Length 11.2″ (28.5 cm) 7.1″ (18 cm) Diameter 0.8″ (2.1 cm) 0.8″ (2.
Two-Year Limited Warranty This Senal product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of two (2) years from the original purchase date or thirty (30) days after replacement, whichever occurs later.