User's Manual
Table Of Contents
- Contents
- Chapter 1: Regulatory Compliance Statements
- Federal Communications Commission (FCC) Compliance Notices
- Class B Interference Statement
- FCC Caution
- RF Radiation Exposure and Hazard Statement
- Non-Modification Statement
- Deployment Statement
- Outdoor operating restrictions
- Dynamic Frequency Selection (DFS) in the 5.0 GHz UNII bands
- Canadian IC Statements
- European Union and European Free Trade Association (EFTA) Regulatory Compliance
- Declaration of Conformity
- European Community Declaration of Conformity
- Countries of Operation and Restrictions of Use in the European Community
- Operation Using the 2.400 to 2.4835 GHz Channels in the European Community
- Operation Using the 5.15 to 5.25 GHz, 5.25 to 5.35 GHz, and 5.470 to 5.725 GHz Channels in the European Community
- Russia, Belarus, and Kazakhstan Requirement
- Antenna Statement
- Chapter 2: Devices with detachable antennas
- Chapter 3: English
- Kapitel 4: Deutsch
- Einführung
- Sicherheitsmaßnahmen
- Installation des WLAN-AP 8120-O
- Hardware
- Kabelanschlüsse
- Abdichten des Ethernet-UTP-Kabels
- Mounten eines WLAN-AP 8120-O an einem vertikalen Mast
- Mounten eines WLAN-AP 8120-O an einem horizontalen Mast
- Mounten eines WLAN-AP 8120-O an einer Wand
- Installation des Ethernet-Überspannungsableiters
- Installation des Power over Ethernet-Injektors
- Sicherheitshinweise
- Capítulo 5: Español
- Introducción
- Precauciones de seguridad
- Instalación del WLAN AP 8120-O
- Hardware
- Requisitos de cableado
- Impermeabilización del cable UTP Ethernet
- Instalación del WLAN AP 8120-O en un poste vertical
- Montaje del WLAN AP 8120-O en un poste horizontal
- Instalación del WLAN AP 8120-O en una pared
- Instalación del disipador de sobretensiones Ethernet
- Instalación del inyector Power over Ethernet
- Advertencias de seguridad
- Chapitre 6 : Français
- Capítulo 7: Português do Brasil
the building. In the event of a local strike, the Ethernet surge arrester instantaneously limits
sudden voltage surges across the cable.
Note:
The Avaya-provided series indoor Ethernet surge arrester is not rated for outdoor use. You
must only install the device indoors.
Warning:
You are required to have a rated surge protector for any cable exiting the building. The
required components must be rated and approved for use in the intended application.
Complete the following general safety guidelines when installing the Avaya Ethernet surge
arrester:
• Mount the Ethernet surge
arrester indoors close to the Ethernet cable exit point from the
building. The cables must exit the building through a customer-provided access, possibly
through the drilled hole where there are communications pipes.
• For best results, install the Ethernet surge arrester indoors in close proximity to a low-
resistance ground at a point where the Ethernet cable exits the building.
• Install the Ethernet surge arrester in an indoor accessible location that allows for periodic
inspection. Provide drip loops in the cables to prevent water from entering the building.
• To connect the Ethernet surge arrester to ground, use the shortest and most direct run
possible with #8 solid copper wire (or equivalent).
See,
Installing the Ethernet surge arrester on page 39 for specifications and installation
instructions for the Ethernet surge arrester.
You can view
, download, and print an expanded version of this document including translations
into French, German, Spanish, and Portuguese from the support portal at http://
www.avaya.com/support . You can also download the complete WLAN 8100 documentation
suite from this location.
©
2012 Avaya Inc.
Installing the WLAN AP 8120-O
This section describes how to:
• mount the WLAN AP 8120-O on a vertical pole
• mount the WLAN
AP 8120-O on a horizontal pole
• mount the WLAN AP 8120-O on a wall
• install an Ethernet surge arrester
• waterproof an outdoor Ethernet cable end plug
• install a Power over Ethernet (PoE) injector
Installing the WLAN AP 8120-O
Avaya WLAN 8100 Regulatory Information — WLAN AP 8120-O February 2012 21