Use and Care Manual

ManualsBrandsSenco ManualsKitchen15-Gauge Angled Finish Nailer

NFD84G Issued Dec. 4, 2006

Les consignes pour l’utilisation en toute sécurité de cet outil se

trouvent dans ce manuel.

Los avisos para el uso seguro de esta herramienta están incluidos

en este manual.

Warnings for the safe use of this tool are included in this manual.

Operating Instructions

Instrucciones de Operacion

Mode d'Emploi

Senco Products, Inc.

8485 Broadwell Road

Cincinnati, Ohio 45244

Questions? Comments?

call SENCO’s toll-free Action-line: 1-800-543-4596

or e-mail: toolprof@senco.com

www.senco.com

FinishPro

42XP

Summary of content (8 pages)

PAGE 1
FinishPro 42XP ® Operating Instructions Instrucciones de Operacion Mode d'Emploi Senco Products, Inc. 8485 Broadwell Road Cincinnati, Ohio 45244 Questions? Comments? call SENCO’s toll-free Action-line: 1-800-543-4596 or e-mail: toolprof@senco.com www.senco.com © 2006 by Senco Products, Inc. Warnings for the safe use of this tool are included in this manual. Los avisos para el uso seguro de esta herramienta están incluidos en este manual.
PAGE 2
English Espanol TABLA DE MATERIAS TABLE OF CONTENTS Tool Use Maintenance Troubleshooting Specifications Options Accessories 1 5 6 6 7 7 EMPLOYER’S RESPONSIBILITIES Employer must enforce compliance with the safety warnings and all other instructions which accompany this tool as shipped from the manufacturer. Keep this manual available for use by all people assigned to the use of this tool. For personal safety and proper operation of this tool, read and understand all of these instructions carefully.
PAGE 3
Tool Use English  With a Contact-Actuation(Dual- Action) trigger, nails can be driven two ways: a) Position workpiece contact (safety element) against work surface and pull trigger...“Trigger Fire”. 1 2 3 4 5 6 7 b) To drive a nail, pull trigger and push workpiece contact (safety element) against work surface. Each time the workpiece contact is pushed against the work surface a nail will be driven.
PAGE 4
Tool Use English  Release E-Z Clear latch and open door. Remove jammed fastener. Close door and latch.  A No-Mar Pad (HF0079) can be added to the bottom of the workpiece contact (safety element) in an effort to help prevent scuffs or damage to the work surface. This pad is marked to indicate the exit point of the nail, making alignment easier.  To adjust the depth of the fas- tener drive, first disconnect the air supply.
PAGE 5
Maintenance English Read and understand “SAFETY INSTRUCTIONS” manual shipped with this tool before using tool.  All screws should be kept tight. Loose screws result in unsafe operation and parts breakage. Maintenimiento Entretien Espanol Francais Antes de usar la herramienta lea y comprenda el manual “INSTRUCCIONES DE SEGURIDAD” despachado con ella.  Todos los tornillos tienen que mantenerse apretados. Los tornillos sueltos pueden producir una operación no segura y quebraduras de partes.
PAGE 6
Troubleshooting Identificación de Fallas Dépannage English Espanol Francais WARNING Repairs other than those described here should be performed only by trained, qualified personnel. Contact SENCO for information at 1-800-543-4596.  Read and understand “SAFETY INSTRUCTIONS” manual shipped with this tool before using tool. AVERTISSEMENT ALERTA Las reparaciones, fuera de aquellas descritas aquí, deben de ser llevadas a cabo solamente por personal entrenado y calificado.
PAGE 7
English TECHNICAL SPECIFICATIONS Minimum to maximum operating pressure Air Consumption (60 cycles per minute) Air Inlet Maximum Speed (cycles per second) Weight Fastener Capacity Tool size: Height Tool size: Length Tool size: Width: Main Body 70–120 psi 3.87 scfm 1 /4 in. NPT 4 4.7 lbs. 104 11 1/4 in. 13 in. 3 1/2 in.
PAGE 8
Limited Warranty SENCO® Pneumatic, DuraSpin®, Cordless Tools & Compressors Senco Products, Inc. (“SENCO”) designs and constructs its products using the highest standards of material and workmanship.