FinishPro™15 FinishPro™18 FinishPro™25XP © 2000, 2002 by Senco Products, Inc.
English Espanol Francais TABLE OF CONTENTS TABLA DE MATERIAS TABLE DES MATIERÈS Tool Use Maintenance Options Troubleshooting Specifications Uso de la Herramienta Mantenimiento Opciones Identificación de Fallas Especificaciones 2 7 8 9 10 Keep this manual available for use by all people assigned to the use of this tool. For personal safety and proper operation of this tool, read and understand all of these instructions carefully.
Tool Use LS1 AZ13 A Uso de la Herramienta Utilisation de l’Outil English Espanol Francais ● Set magazine height adjustment lever (A) before loading fasteners. ● Coloque en posición correcta la palanca de ajuste de la altura del cargador antes de cargarlo con clavos. ● Positionnez le levier de réglage de hauteur du magasin avant chargement des projectiles. ● Set magazine height adjustment lever (A) before loading fasteners.
Tool Use Uso de la Herramienta Utilisation de l’Outil Espanol English FinishPro™10 / LS FinishPro™15/18/25XP SLP20 FinishPro™25XP Turbo Setting Standard Setting For 30% more Power For most jobs ● Position tool against work surface and pull the trigger. ● Coloque la herramienta contra la superficie de trabajo y apretar el gatillo. Francais ● Position l’appareil contre la surface de travail et presser sur la gâchette.
Tool Use Uso de la Herramienta Utilisation de l’Outil Espanol Francais 1.) Disconnect the air from the tool. If the air is not removed from the tool, the adjustment cannot be made. 2.) Using wrenches provided with the tool, insert in hole and move to the desired setting (forward - Turbo Setting) or (back - Standard Setting). 1.) Desconecte la alimentacíon de aire a la herramienta. Si la alimentacíon de aire no se quita de la herramienta, no se puede efectuar el ajuste. 2.
Tool Use Uso de la Herramienta Utilisation de l’Outil Espanol English ● Keep the tool pointed away from yourself and others and connect air to tool. FinishPro™25XP SLP20 & FinishPro™25XP ● Mantenga la herramienta apuntada en la dirección opuesta de usted y de otros y conecte el aire a la manguera. ● To adjust the direction of the exhaust air, turn the exhaust deflector to the desired location.
™ FinishPro 10/15/18 & LS Maintenance Maintenimiento English Espanol ● Squirt Senco pneumatic oil (5 to 10 drops) into the air inlet twice daily (depending on frequency of tool use). Other oils may damage O-rings and other tool parts. ● Wipe tool clean daily and inspect for wear. Use non-flammable cleaning solutions only if necessary–DO NOT SOAK. Caution: Such solutions may damage O-rings and other tool parts.
SLP20 A A B/C B C Troubleshooting Identificación de Fallas Dépannage English Espanol Francais WARNING ALERTA Repairs other than those described here should be performed only by trained, qualified personnel. Contact SENCO for information at 1-800-543-4596. Las reparaciones, fuera de aquellas descritas aquí, deben de ser llevadas a cabo solamente por personal entrenado y calificado. Póngase en contacto con SENCO para información 1-800-543-4596.
Specifications Especificaciones Specifications English Espanol Francais TECHNICAL SPECIFICATIONS SLP20 Minimum to maximum operating pressure Air Consumption (60 cycles per second) Air Inlet Maximum Speed (60 cycles per second) Weight Fastener Capacity Tool size: Height Tool size: Length Tool size: Width: Main Body 70–120 psi 1.92 scfm 1 ⁄4 in. NPT 5 2.3 lbs. 110 8 1⁄4 in. 9 1⁄2 in. 2 in.
FinishPro™15/18 FinishPro™25XP Specifications Especificaciones Specifications English Espanol Francais MODEL: 760002N 1T0001N / 1U0001N MODEL: 760002N A A .050 in. 1,27 mm AY10 AY11 AY13 AY15 AY17 AY18 LS .050 in.
SHP10 FinishPro™10 Specifications Especificaciones Specifications English Espanol Francais MODEL: 2C0001N MODEL: 550001N A A .025 in. ,64 mm .025 in. ,64 mm CZ08 (JS12) CZ10 (JS15) CZ11 (JS18) SLP20 A Code A Code (Europe) mm 12 15 18 Inches 1 ⁄2 5 ⁄8 3 ⁄4 A100509 A100629 A100759 A101009 Inches 1 ⁄2 5 ⁄8 3 ⁄4 1 MODEL: 430001N MODEL: 430001N A A .050 in. 1,27 mm AY10 AY11 AY12 .050 in.
SENCO TOOL & PARTS WARRANTY This tool has been designed and constructed using the highest standards of material and workmanship. TOOL AND PARTS WARRANTYThe length of this guarantee is two years [During the applicable period for XtremePro (XP) Series tools] or one year [During the applicable period for most other Senco tools/see pertinent literature for these tools] from date of purchase by the original retail purchaser. During this period, Senco Products, Inc.
